Johnson Controls Tyco PowerSeries Pro HS3032 Bedienungsanleitung

PowerSeries Pro Reference Manual

HS3032 / HS3128 / HS3248

This manual contains information on limitations regarding product use, function and information on the limitations as to liability of the

manufacturer. Carefully read the entire manual.

Contents

1.0 Safety instructions 4

Section 1: Introduction 5

1.1 About the system 5

Section 2: Installation 11

2.1 Before installing the equipment 11

2.2 Overview of installation process 11

2.3 Alarm controller installation 11

2.4 General wiring instructions 18

2.5 Installing modules 36

Section 4: Configuration 54

4.1 Basic configuration steps 54

4.2 Using the keypad 54

4.3 Enrollment 55

4.4 Working with partitions 56

4.5 Trouble indicators 57

4.6 Keypad partition setup 57

4.7 Alternate communicator setup 59

4.8 Local firmware upgrade 60

4.9 Testing the system 60

Section 5: System operation 61

5.1 Arming and disarming 61

5.2 Partition vs. global keypad 61

5.3 Labels 62

5.4 Annunciation 63

5.5 Keypad function keys 63

5.6 Language selection 66

5.7 [*] Commands 66

5.8 Visual verification 79

Section 6: Programming 81

6.1 How to program 81

6.2 Programming methods 81

6.3 Programming descriptions 84

Section 7: Programming Worksheets 161

7.1 Label Programming 161

7.2 Zone Setup 170

7.3 End Of Line Resistance 173

7.4 System Times 173

7.5 Access Codes 177

7.6 PGM Programming 177

7.7 System Lockout 201

7.8 System Options 202

7.9 Auto arm/disarm 206

7.10 Partition and Zone Assignment 218

7.11 Communications 232

7.12 Call Directions 240

7.13 DLS Programming 248

7.14 Virtual Inputs 249

7.15 Schedule Programming 249

7.16 Audio Module Programming 254

7.17 Wireless Programming 262

7.18 Alternate Communicator 262

7.19 Keypad Programming 270

7.20 Template Programming 272

7.21 System Information 272

- 2 -

7.22 Module Programming 273

7.23 Wireless Placement Testing 274

7.24 Battery Settings 276

7.25 Restoring Factory Defaults 277

Section 8: Troubleshooting 278

8.1 Testing 278

8.2 Troubleshooting 278

Appendix 1: Reporting codes 288

1.1 Contact ID 288

1.2 SIA Format - Level 2 (Hard Coded) 288

1.3 Contact ID & SIA Zone Alarm/Restore Event Codes 294

Appendix 2: Word library 296

Appendix 3: Template programming tables 297

3.1 Digit 1 – Zones 1-8 Definition Options 297

3.2 Digit 2 – System EOL Configuration Options 297

3.3 Digit 3 – Reporting Code Communication Options 297

3.4 Digit 4 – Reporting Code Configuration Options 299

3.5 Digit 5 - DLS Connection Options 301

Appendix 4: ASCII Characters 303

Appendix 5: Regulatory approvals 304

5.1 FCC COMPLIANCE STATEMENT 304

5.2 Innovation, Scientific and Economic Development Canada (ISED) Statement 305

5.3 UL/ULC Installations 305

5.4 SIA False Alarm Reduction Installations: Quick Reference 309

5.5 European EN50131 Compliance Statement 311

5.6 UK Compliance Statement 313

Appendix 6: UL/ULC Wiring Diagram 315

6.1 HS3032, HS3128, and HS3248 UL/ULC wiring diagram (North America only) 315

Appendix 7: Specifications 316

Appendix 8: Locating detectors and escape plan 319

8.0 Locating detectors and escape plan 319

8.1 Smoke Detectors 319

8.2 Fire Escape Planning 320

8.3 Carbon Monoxide Detectors 320

Appendix 9: New Features Listing 321

- 3 -

1.0 Safety instructions

Read the safety information before you install the equipment.

Important: This equipment must be installed by a skilled person only. A skilled person is an installer with appropriate technical

training. The installer must be aware of potential hazards during installation and measures available to minimize risks to the

installer and other people.

lBefore you install this equipment disconnect all power sources (for example mains, battery, and telephone line) connected to

the alarm panel.

lInstall the equipment indoors in a non-hazardous environment where the following conditions are met:

- Pollution degree - Maximum 2

- Over voltages - Category II

lInternal wiring must be routed to prevent

- strain on wire and terminal connections

- loose terminal connections

- damage to conductor insulation.

Note: Instruct the user that there are no user serviceable parts in this equipment. All equipment must be serviced by a skilled person.

Warning: This equipment has no mains on/off switch. The plug of the direct plug in versions of this equipment is intended to serve as

the disconnecting device. It is imperative that access to the mains plug and associated mains socket/outlet is never obstructed. For

permanently connected versions of this equipment the fuse in the connector block is the disconnect device. If the neutral wire cannot

be identified, then this equipment must be connected to a mains source that comes from a disconnect device that simultaneously

disconnects both poles (Line and Neutral).

- 4 -

Section 1: Introduction

1.1 About the system

The PowerSeries Pro alarm panel is a feature-rich, scalable alarm system designed for commercial use. The alarm panel supports

both hardwired and wireless devices. This section lists the features of the alarm panel, available models, and compatible devices.

The following symbols are used to indicate features or methods of operation that are only available in a particular market. No symbol

indicates the feature or operation is available for all markets unless noted specifically otherwise.

CP-01

- North America

- Europe

NFA2P

- France

- United Kingdom

Features

The following features are available on the PowerSeries Pro alarm controller.

Zones, wireless keypads, wireless keys, panic pendants, and proximity tags

The system supports the following devices:

l32 or 128 wireless zones or 32, 128, or 248 wired zones. This includes the 8 wired zones available on the controllers.

l41 zone types and 15 programmable zone attributes.

l8, 16, or 32 separate keypads supported.

l32 separate wireless keys supported.

l72 or 1000 separate proximity tags supported.

Access codes

lUp to 1002 access codes: 1000 (level 2-EN) including one system master code (level 2-EN). In addition, one installer code

(level 3-EN), and one maintenance code are available.

Note: EN50131-1 compliant systems using more than 100 access codes shall set the access code to 8 digits (section [041],

option 02).

lProgrammable attributes for each user code (see "Access code attributes" on page 74)

Programmable outputs (PGMs)

lUp to 4 programmable outputs (PGM) on the alarm controller with 50 available options.

l44, 166, or 180 maximum programmable outputs for HS3032, HS3128, HS3248.

System supervision features

The PowerSeries Pro continuously monitors a number of possible trouble conditions and provides audible and visual indication at

the keypad. Trouble conditions include:

lAC power failure

lZone trouble

lFire trouble

lTelephone line trouble

lCommunicator trouble

lLow battery condition

lRF jam

lAUX power supply fault

lFailure to communicate

lModule fault (supervisory or tamper)

lBell trouble

lCorbus troubles

lPower unit trouble

- 5 -

Section 1: Introduction

Available models

The following alarm controller models are available:

lHS3032

lHS3128

lHS3248

Model comparison

The table below lists the features of each alarm system model.

Table 1-1: Model comparison

Features HS3032 HS3128 HS3248

On board

Zones 8 8 8

PGMs 4 4 4

2-way audio interface 1 1 1

Cellular plug-in interface 1 1 1

On-board ethernet connection 1 1 1

PC-link interface 1 1 1

USB connectors 2 2 2

PC- Link 1 1 1

Expansion

Zones 32 128 248

Low current PGMs 32 128 128

High current PGMs 4 16 16

Relay output PGMs 4 32 32

Partitions 4 8 32

Keypads 8 16 32

Users 72 1000 1000

Standard event buffer 500 1000 1000

Priority event buffer 2000 2000 2000

Alarm buffer 100 100 100

Arming buffer 100 100 100

Wireless device expansion

Wireless zones 32 128 128

Panic pendant zones 32 32 32

Wireless keys 32 32 32

Sirens 8 16 16

Repeaters * 8 8 8

Module expansion

PowerG transceiver - HSM2HOST or LCD keypad with prox

and host (HS2LCDRFPROx) **

111

8-zone expander - HSM2108 *** 3 15 30

8-zone expander - HSM3408 *** 3 15 30

PGM expander - HSM2208 4 16 16

3A power supply - HSM3350 3 4 4

1A power supply - HSM2300 3 4 4

Power supply with 4 outputs - HSM2204 1 4 4

2-way audio module - HSM2955 1 1 1

Corbus repeater - HSM3204CX 1 8 16

Plug-in cellular module - XX9080 1 1 1

- 6 -

Section 1: Introduction

Features HS3032 HS3128 HS3248

LCD Keypad with Prox - HS2LCDPRO 8 16 32

Touchscreen with Prox - HS2TCHPRO(BLK) 8 16 32

Wire-free Keypad with Prox - HS2LCDWFPROx 8 16 16

Wire-free Keypad Prox and Voice - HS2LCDWFVPROx 8 16 16

* For UL installations, 2 wireless repeaters must be installed for proper signal routing.

** Only one PowerG transceiver can be enrolled on a PowerSeries Pro panel. The PowerG transceiver can be an HSM2HOST or an

LCDkeypad with host (HS2LCDRFPROx).

*** The HSM3408 and HSM2108 can be enrolled on the system at the same time, but each take up 1-zone expander module slot.

The maximum combined zone expander modules slots are 3 on the HS3032, 15 on the HS3128, and 30 on the HS3248.

- 7 -

Section 1: Introduction

Compatible devices

The following wireless devices and modules are compatible with this alarm controller. In the table below and throughout this

document, x in the model number represents the operating frequency of the device as follows: 9 (912-919 MHz), 8 (868MHz), 4

(433MHz). Only models operating in the band 912-919 MHz are UL/ULC listed where indicated.

Note: Only UL approved devices are to be used with UL/ULC listed systems.

Note: PowerSeries Pro supports v1.40 or higher keypad versions only. Neo keypads (keypad versions less than 1.40) are not

compatible with PowerSeries Pro panels.

Note: For ULC-s559 listed applications the HS2TCHPRO(BLK) touchscreen keypad is for supplementary use only.

Table 1-2: Compatible devices

Modules

UL/ULC Listed EN50131 Grade 2

certified

EN50131 Grade

certified

HS2LCDWFPROx wireless keypad HS2LCDWFPRO9 HS2LCDWFPRO8 _

HS2LCDWFVPROx wireless keypad with voice HS2LCDWFVPRO9 HS2LCDWFVPRO8 _

HS2LCDRFPROx hardwired keypad with PG transceiver HS2LCDRFPRO9 HS2LCDRFPRO8 _

HS2LCDPRO hardwired keypad HS2LCDPRO _ HS2LCDPRO

HS2TCHPRO touchscreen keypad (white enclosure) HS2TCHPRO _ HS2TCHPRO

HS2TCHPROBLK touchscreen keypad (black enclosure) HS2TCHPROBLK _ HS2TCHPROBLK

HSM2HOSTx 2-way PowerG wireless transceiver HSM2HOST9 HSM2HOST8 _

HSM2108 8-zone expander HSM2108 HSM2108 _

HSM2208 8-zone, low-current output expander HSM2208 HSM2208 _

HSM3408 8-zone expander with diagnostics HSM3408 _ HSM3408

HSM2204 4-zone, high-current output expander HSM2204 HSM2204 _

HSM2955(R) audio verification module HSM2955(R) HSM2955(R) _

HSM3204CX power supply/relay output/corbus repeater module HSM3204CX _ HSM3204CX

HSM2300 1A power supply HSM2300 HSM2300 _

HSM3350 3A power supply HSM3350 _ HSM3350

HSM3WIFI USB to WiFi adapter _ _ _

3G9080 Alternate communicator 3G9080 _ _

LE9080 Alternate communicator LE9080 _ _

3G9080-EU Alternate communicator _ _ 3G9080-EU

TL880LT Alternate communicator TL880LT _ _

TL8803G Alternate communicator TL8803G _ _

TL880LE Alternate communicator TL880LE _ _

PowerG wireless devices

PGx862 Ceiling mount detector with temperature monitoring - short range PG9862 PG8862 _

PGx872 Ceiling mount detector with temperature monitoring - long range PG9872 PG8872 _

PGx902 Outdoor curtain PIR PG9902 PG8902 _

PGx904(P) PIR motion detector with optional animal resistance PG9904(P) PG8904(P) _

PGx914(P) PIR motion detector with temperature monitoring PG9914(P) PG8914(P) _

PGx924 Curtain PIR motion detector PG9924 PG8924 _

- 8 -

Section 1: Introduction

PGx934(P) PIR motion detector with camera PG9934(P) PG8934(P) _

PGx944 Outdoor PIR motion detector with camera and anti-masking PG9944 PG8944 _

PGx974(P) Mirror optic PIR motion detector PG9974(P) PG8974(P) _

PGx984(P) Dual technology (PIR and MW) with anti-masking PG9984(P) PG8984(P) _

PGx994 Outdoor PIR motion detector with anti-masking PG9994 PG8994 _

PGx307 Recessed door/window contact PG9307 PG8307 _

PGx312 Outdoor contact with aux input, temperature monitoring and anti-

mask

PG9312 PG8312 _

PGx945 Door/window contact with auxiliary input PG9945 PG8945 _

PGx975 Vanishing door/window contact PG9975 PG8975 _

PGx912 Glassbreak detector PG9912 PG8912 _

PGx922 Glassbeak detector PG9922 PG8922 _

PGx935 Shock detector with auxiliary input PG9935 PG8935 _

PGx985 Flood detector PG9985 PG8985 _

PGx905 Temperature detector PG9905 PG8905 _

PGTEMP-PROBE Temperature probe extender (requires PGx905) PGTEMP-PROBE _ _

PGx913 CO detector (US only) PG9913 PG8913 _

PGx933 CO detector with temperature monitoring PG9933 PG8933 _

PGx936 Smoke/heat detector with temperature monitoring PG9936 PG8936 _

PGx901 Indoor siren PG9901 PG8901 _

PGx911 Outdoor siren PG9911 PG8911 _

PGx920 Wireless repeater PG9920 PG8920 _

PGx938 one-button panic key PG9938 PG8938 _

PGx949 two-button panic key PG9949 PG8949 _

PGx929 four-button panic key PG9929 PG8929 _

PGx939 four-button panic key PG9939 PG8939 _

PGx303 Magnetic contact PG9303 PG8303 _

PGx309 Commercial magnetic contact

Note: The PGx309 is supported with HSMHOST version 1.33 or

higher.

PG9309 PG8309 _

Central station receivers

SG-System I, II, III, IV, 5 SG-System I, II, III, IV,

_ _

Hardwired devices

- 9 -

Section 1: Introduction

2-wire smoke detector: x = A, B, or C

A = ULC listed models

B = UL listed models

C = European and Australian models

L = Remote LED output

R = Auxiliary form C relay

S = Sounder

T = Temperature sensor

FSA-210xUL

FSA-210xTUL

FSA-210xSUL

FSA-210xSTUL

FSA-210xLSTUL

FSA-210xRUL

FSA-210xRTUL

FSA-210xRSUL

FSA-210xRSTUL

FSA-210xLRSTUL

4-wire smoke detector: x = A, B, or C

A = ULC listed models

B = UL listed models

C = European and Australian models

L = Remote LED output

R = Auxiliary form C relay

S = Sounder

T = Temperature sensor

FSA-410xUL

FSA-410xTUL

FSA-410xSUL

FSA-410xSTUL

FSA-410xLSTUL

FSA-410xRUL

FSA-410xRTUL

FSA-410xRSUL

FSA-410xRSTUL

FSA-410xLRSTUL

CO detector CO-12/24UL

12-24SIRUL

FW-CO12UL

FW-CO1224UL

CO1224UL

Enclosures

The PowerSeries Pro main board can be installed in the metal enclosures listed below. Tamper protection switches can be installed

on all enclosures, including door opening protection and/or removal from the mounting position. Doors can be secured using screws

or a keylock.

HSC3010C (with hinged door) 18 Ga steel, white, dimensions 372 mm x 412 mm x 114

mm, weight: 9.75 lb or 4.2 kg

HSC3010CR (with hinged door) 18 Ga steel, red, dimensions 372 mm x 412 mm x 114 mm,

weight: 10.0 lb or 4.5 kg

HSC3030CAR (with hinged door) 18 Ga steel (base) and 16Ga (door), white, dimensions 375

mm x 412 mm x 114 mm, weight: 11.45 lb or 5.2 kg

HSC3020C (with removable door) 18 Ga steel, white, dimensions 459 mm x 414 mm x 103

mm, weight: 4.3 kg (no batteries)/12 kg (17Ah)

HSC3020CP (with removable door) PC-ABS, white, dimensions 368 mm x 489 mm x 108 mm,

weight: 2.3 kg (no batteries)/7.7 kg (17Ah)

For EN50131-1 Grade 2 or Grade 3 compliant installations, all holes on the side of the cabinets shall be covered (plugged) if

unused. The equipment enclosure must be secured to the building structure before operation. Use four screws (appropriate for the

wall material on which it is attached) inserted through the four mounting holes provided in the back of the enclosure base.

- 10 -

Andere Handbücher für Tyco PowerSeries Pro HS3032

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Johnson Controls Sicherheitssystem Handbücher

Johnson Controls

Johnson Controls Qolsys IQ Remote PowerG Bedienungsanleitung

Johnson Controls

Johnson Controls tyco RAPID RESPONSE RCP-1 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco PowerSeries Pro Bedienungsanleitung

Johnson Controls

Johnson Controls IFI-WS Bedienungsanleitung

Johnson Controls

Johnson Controls METASYS PS12ADA Series Bedienungsanleitung

Johnson Controls

Johnson Controls P2000 Handbuch

Johnson Controls

Johnson Controls IQ Panel 4 Bedienungsanleitung

Johnson Controls

Johnson Controls P2000 Bedienungsanleitung

Johnson Controls

Johnson Controls P2000 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco WS900 UL Bedienungsanleitung

Johnson Controls

Johnson Controls IFC-1010 Handbuch

Johnson Controls

Johnson Controls Qolsys IQ Remote PowerG Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco PowerSeries Pro HS3032 Bedienungsanleitung

Johnson Controls

Johnson Controls Intelligent Fire Integrator NION-16C48M Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Johnson Controls

Johnson Controls Tyco PowerSeries Pro HS3032 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung

DSC

DSC PC 4010 Betriebsanleitung

UniPOS

UniPOS 6202L Bedienungsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Rondish

Rondish Nexus Bedienungsanleitung

Pego

Pego ECP APE03 Bedienungsanleitung