Johnson Level & Tool 40-6005 Bedienungsanleitung

Laser Dista ce Measure

Model No. 40-6005

Instruction Manual

Congratulations on your choice of this Laser Distance Measure. We

suggest you read this instruction manual thoroughly before using the

instrument. Save this instruction manual for future use.

This is a Class II laser tool and is manufactured to comply with CRF 21,

parts 1040.10 and 1040.11 as well as international safety rule IEC 285.

The laser also complies with EMC Test according to EN61000-6-3;

2001+A11:2004, EN 6100-6-1:2011, EN 6100-4-2, EN 61000-4-3,

EN 60825, FCC Test according to PART 15.

4533H-English_Manuals 4/1/11 10:49 AM Page 1

Table of Contents

1.Kit Contents . . . . . . . . . pg. 2

2.Safety Information . . . pg. 2-3

3.Location/Content of

Warning Labels . . . . . . . pg. 3

4.Location of Parts/

Components . . . . . . . pg. 4-5

5.Start Up - Battery Installation

Instructions . . . . . . . . . . pg. 7

6.Using the Product . . pg. 8-19

Technical Specifications

pg. 20

8.Product Warranty. . . . . pg. 21

9.Product Registration . . pg. 22

1. Kit Contents

Description for Model 40-6005 Qty.

Laser Distance Measure

Protection Cover 1

Wrist Strap 1

“AA” Alkaline Batteries 2

Instruction Manual 1

Soft-Sided Pouch 1

2. Safety Instructions

Please read and understand all of the following instructions, prior

to using this tool. Failure to do so, may result in bodily injury.

CAUTION!

Class II Laser Product

Max. Power Output: ≤1mW

Wavelength: 640-660nm

THIS TOOL EMITS LASER RADIATION.

DO NOT STARE INTO BEAM.

AVOID DIRECT EYE EX OSURE.

4533H-English_Manuals 4/1/11 10:49 AM Page 2

ATTENTION IMPORTANT

• Read all instructions prior to operating this laser tool. Do not remove any labels from tool.

• Do not stare directly at the laser beam.

• Do not project the laser beam directly into the eyes of others.

• Do not set up laser tool at eye level or operate the tool near a reflective surface as

the laser beam could be projected into your eyes or into the eyes of others.

• Do not place the laser tool in a manner that may cause someone to unintentionally

stare into the laser beam. Serious eye injury may result.

• Do not operate the tool in explosive environments, i.e. in the presence of gases or

flammable liquids.

• Keep the laser tool out of the reach of children and other untrained persons.

• Do not attempt to view the laser beam through optical tools such as telescopes as

serious eye injury may result.

• Always turn the laser tool off when not in use or left unattended for a period of time.

• Remove the battery when storing the tool for an extended time (more than 3 months) to

avoid damage to the tool should the batteries deteriorate.

• Do not attempt to repair or disassemble the laser tool. If unqualified persons attempt

to repair this tool, warranty will be void.

3. Location/Content of Warning Labels

4533H-English_Manuals 4/1/11 10:49 AM Page 3

4. Location of art/Components

1. LCD Display

2. Add/Unit of Measure

3. Measure Button

4. Measure Function

Area

Volume

Stake-Out

5. Countdown Measure/

Memory Recall

6. Wrist Strap Bracket

7. Laser Emitting Window

8. Subtract/Back-Light

9. Indirect Measurement/Pythagoras

10. Power Button/Clear/Escape

11. Measuring Reference Position/

Continuous Laser Mode

12. Receiver Window

13. Battery Cover

14. Corner Measurement

Extension Piece

4533H-English_Manuals 4/1/11 10:49 AM Page 4

1. Active Laser Indicator

2. Indirect Measuring

Single Pythagoras

Double Pythagoras

(Partial Height)

3. Measuring Function

Area Measuring

Volume Measuring

4. Measurement Reference Position

5. Add and Subtract

6. Maximum Display

7. Minimum Display

8. Stake Direction Indicator

9. Main Screen and

Units of Measure

10. Countdown Measuring Timer

11. Memory Counter

12. Battery Status

13. Sub-Screen and Units

of Measure

4533H-English_Manuals 4/1/11 10:49 AM Page 5

Measuring Reference

Range

Range is specified between a minimum 2-inches to a maximum of

230-feet with an accuracy of 1/16”. Longer ranges will be found by the

instrument but a variance in the accuracy may exist. At night or dusk

the range may be greater than during daylight or if the target has poor

reflective properties.

Target Surfaces

Measuring errors may occur when aiming at surfaces composed

of colorless liquids (e.g. water), glass, Styrofoam or similar semi-

permeable surfaces. Aiming at high gloss surfaces may deflect the

laser beam and lead to measurement errors.

Hazards of Use

Be aware that errors in distance measurements may occur if the

instrument is defective or has been dropped, been misused or

modified.

Note

Conduct periodic test measurements to ensure the instrument is

measuring accurately and consistently. This is most important if the

instrument has been exposed to abnormal use. Always confirm

accuracy before and during important measurements. Keep the laser

distance measure optic clean and inspect for damage.

4533H-English_Manuals 4/1/11 10:49 AM Page 6

5. Start Up - Battery Installation

1. Remove battery compartment lid.

2. Insert 2-“AA” batteries observing

correct polarity.

3. Close battery compartment lid.

4. Battery status will be shown in start

up screen.

5. When the icon appears there are

approximately 1,000 measurements

remaining.

6. Replace batteries when the icon flashes on the screen.

7. Remove old batteries and replace with new “AA” alkaline batteries

following steps 1-3 above.

Note

Use only alkaline batteries. If the instrument will not be used for an

extended time, remove the batteries to protect against corrosion.

ower Button

Press Power Button to power up.

Press and hold Power Button to power off.

Automatic Shutoff

Laser will turn off after 30 seconds

Unit will turn off after 3 minutes of inactivity

4533H-English_Manuals 4/1/11 10:49 AM Page 7

6. Using the roduct

Measuring

Measuring Modes

Your Laser Distance Measure has four

measuring modes:

Length

Area/Square

Volume/Cube

Indirect/Pythagoras

Units of Measure

This instrument has five units of measure. The desired unit of measure

can be set by pressing and holding for two seconds. The main

screen will display square feet/square meters or cubic feet/cubic

meters in a decimal format when calculating area and volume.

The following units can be set:

Distance Area Volume

1. 0.000 m 0.000 m20.000 m3

2. 0.00 ft 0.00 ft20.00 ft3

3. 0’0” 1/32 0.00 ft20.00 ft3

4. 0.00 in 0.00 ft20.00 ft3

5. 0 1/32 in 0.00 ft20.00 ft3

4533H-English_Manuals 4/1/11 10:49 AM Page 8

Measurement Reference osition

Be sure to adjust the measuring reference position prior to engaging a

measuring calculation mode. Press and release to scroll through

the reference point options

Front

Rear

Corner Extension Piece

Single Distance Measuring

Press to turn power on.

Direct Laser Beam to Target.

Press and release .

Keep unit still until measurement has been

recorded. Laser beam will shut off once

measurement has been recorded.

Recorded measurements (up to 20 measurements will be stored

automatically and available for recall, see Memory Recall page 18).

Press and release to clear screen.

Press and hold to power down unit

4533H-English_Manuals 4/1/11 10:49 AM Page 9

Measuring with Countdown Timer

Press and release .

icon will appear on screen with

default setting of three second

countdown timer.

Press and release to activate

laser (if inactive.)

Direct the laser beam towards the target and hold steady.

Press and release to activate the countdown timer.

Measurement will be recorded on screen.

Repeat these steps for each measurement. Countdown measuring may be

used during any measuring function (e.g. Pythagorean, area, volume, etc).

To extend the time from three seconds press and release until

you reach desired time. Timer can be set up to 15 seconds.

Adding or Subtracting

Press and release the button to activate laser.

Press and release the button to record first measurement.

Press and release (first measurement moves to sub value position

on screen and a “+” sign temporarily appears).

Press and release the button to activate laser. (If inactive.)

Press and release the button to record second measurement.

Press and release to add measurement 1 (stored in sub value

position) and measurement 2 together.

4533H-English_Manuals 4/1/11 10:49 AM Page 10

Inhaltsverzeichnis

Andere Johnson Level & Tool Messgerät Handbücher

Johnson Level & Tool

Johnson Level & Tool 1750-1000 Bedienungsanleitung

Johnson Level & Tool

Johnson Level & Tool JLX 40-6590 Bedienungsanleitung

Johnson Level & Tool

Johnson Level & Tool 40-6601 Bedienungsanleitung

Johnson Level & Tool

Johnson Level & Tool 40-6603 Bedienungsanleitung

Johnson Level & Tool

Johnson Level & Tool 1886-0300 Bedienungsanleitung

Johnson Level & Tool

Johnson Level & Tool 1887-0000 Bedienungsanleitung

Johnson Level & Tool

Johnson Level & Tool 1889-0600 Bedienungsanleitung

Johnson Level & Tool

Johnson Level & Tool LDM330 Bedienungsanleitung

Johnson Level & Tool

Johnson Level & Tool 40-6645 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung