Johnson 40-6250 Bedienungsanleitung

Machine Mountable Electronic Level

with Bluetooth

Model No. 40-6250

Instruction Manual

Congrat lations on yo r choice of this Machine Mo ntable Electronic

Level with Bl etooth. We s ggest yo read this instr ction man al

thoro ghly before sing the instr ment. Save this instr ction man al

for f t re se. Additional copies are available at

www.johnsonlevel.com.

Bluetooth is a trademark of Bluetooth SIG, Inc.

6657H-A _Manua s 1/28/13 1:45 PM Page 1

Table of Contents

1. Kit Contents

2. Features and Functions

3. Safety Instructions

4. Location of Parts/Components

5. Operating Instructions

6. Using the Remote

Control/Receiver

7. Technical Specifications

8. Care and andling

9. Product Warranty

10. Warranty Registration

1. Kit Contents

odel No. 40-6250 Qty.

Sensor/Slaver (includes 3 AA batteries) 1

Remote Control/Receiver (includes 3 AA batteries) 1

DC 5V adapter 1

Remote cable & PC cable 1

Instruction manual 1

Carrying case 1

2. Features and Functions

• Use for new machinery installation and relocation

• Measures level in X and Y axis to within a maximum accuracy of

0.01 degrees

• Operation range is ± 10 degrees of level

• Reads slope in %, mm/m, and in/ft

• Remote control features large LCD screen that reads in X or Y axis

• Green backlit screen reads digitally and graphically

• Reads via cable outlet or wireless Bluetooth

• Bluetooth supported operating range 32’

6657H-A _Manua s 1/28/13 1:45 PM Page 2

3. Safety Instructions

Please read and understand all of the following instructions, prior

to using this tool. Failure to do so, may void the warranty.

ATTENTION IMPORTANT

• Read all instructions prior to operating this tool. Do not remove any labels from tool.

• Always turn the tool off when not in use or left unattended for a period of time.

• Remove the batteries when storing the tool for an extended time (more than 3 months)

to avoid damage to the tool should the batteries deteriorate.

• Do not attempt to repair or disassemble the tool. If unqualified persons attempt

to repair this tool, warranty will be void.

• Use only original Johnson®parts and accessories purchased from your Johnson®

authorized dealer. Use of non-Johnson®parts and accessories will void warranty.

6657H-A _Manua s 1/28/13 1:45 PM Page 3

4. Location of Parts/Components

Red Power Light

Scan Channel Light

Data Transfer

Light

Data

Transfer Port

Out Supply

Port

Remote Control/Receiver Port

Sensor/Slaver

Link Light

Power Button Dust-proof

Lid Port

6657H-A _Manua s 1/28/13 1:45 PM Page 4

5. Operating Instructions

Sensor/Slaver

Battery Installation

The Sensor/Slaver requires 3 “AA”

alkaline batteries to operate. Locate

the battery door on bottom as shown in

photo. Loosen screws, remove cover and install the batteries with

correct polarity. Securely re-install battery door.

Power On and Off

old the power button for one second

to power on the Sensor/Slaver. An

audible beep and visual LED light will

confirm the power is on.

old the power button for one second

to power down the Sensor/Slaver. An audible beep and visual LED

power light will confirm the power is off.

Remote Control/Receiver

Battery Installation

The Remote Control/Receiver requires 3 “AA” alkaline batteries to

operate. Locate battery door, remove cover and install the batteries

with correct polarity. Securely re-install battery door.

6657H-A _Manua s 1/28/13 1:45 PM Page 5

6. Using the Remote Control/Receiver

Remote Display

1. Power Button (POW)

a. old for one second to power up Sensor/Slaver with beep.

b. old for two seconds to turn off Remote Control/Receiver

with beep.

2. easure Button ( EAS)

a. Push button to enable measuring and lock control pad

with beep and visual LED is lit.

b. Push button again to disable measuring and unlock control

pad with beep and visual LED is off.

6657H-A _Manua s 1/28/13 1:45 PM Page 6

Note: All operation buttons will be non-responsive, except buttons 1,

2, & 7. Push the MEAS button again so light turns off to utilize

buttons 3, 4 and 5 below.

Begin measuring only after the link light of the Remote

Control/Receiver and Sensor/Slaver are illuminated. If there is a

delay in the illumination or the units are not connected, power down

and then power up again.

3. Resolution Button (SEN/DEG)

Pushing this button will switch resolutions

a. 0.002º - 0.01º - 0.1º - 1º - 0.002º

b. Degree - Minute - Second

4. Function Button (mm, m; in/ft; CHN)

Pushing this button will switch functions

a. Percentage of Slope (%)

b. mm / M

c. in / ft

d. Channel Select (A-B-A)

5. Absolute, Relative and Degree Button (ABS/REL, WARN)

a. Absolute and Relative: switch between absolute and

relative value

b. Degree Alert Set-Up

1. When degrees stop to X1 and Y1, press MEAS to

pause measure.

2. Press and hold this button until 3 beeps are heard to set

alarm mode for 1 degree, LCD will display “1”.

6657H-A _Manua s 1/28/13 1:45 PM Page 7

3. Then press MEAS and move sensor to another

desired X2 and Y2.

4. Pause MEAS again and hold same button until 3

beeps are heard for set degree 2, LCD will display “2”.

5. Remote Control/Receiver will beep when Sensor/Slaver is

out of range (1 and 2).

6. To disable alert, press this button to enable 1 and 2.

Note: X & Y axis must be set independently. Preset minimum and

maximum alarm prior to setting on surface to be leveled.

6. Lock and Quiet Button (LOCK/QUIET)

a. Lock: to lock control pad

b. Quiet: to disable beeper

Note: All operation buttons will be non-responsive, except buttons

1 & 6 - locking button.

7. Select Axis, Backlight and Calibration Button

(X/Y BACKLED)

a. Select Axis: press to switch display between X, Y, X n Y

b. Backlight: hold for 2 seconds to turn on/off backlight

c. Calibration: if this function is not working, please do not

operate, it could cause level displacement. If the precision

of the instrument is not correct and cannot be corrected,

please send it back to Johnson Level & Tool for test and

maintenance.

6657H-A _Manua s 1/28/13 1:45 PM Page 8

Calibration Procedure:

1. Put sensor on a flat plate (±3°)

2. Power up sensor and remote. Red LED power light is on both

devices.

3. old the X/Y back LED icon for 5 seconds to enter

calibration mode. There will be five beeps.

4. The LCD screen is flashing except for the number 1. This

means you have entered calibration step 1.

5. Press the X/Y back LED icon again to enter calibration

step 2. First beep acknowledges the button press. The three

additional beeps indicate it has entered the 2nd stage of

calibration.

6. Rotate the sensor 180°, then press the X/Y back LED icon

button again (see below illustration).

7. The “2” will disappear and calibration is finished.

Rotate 180º Clockwise

Johnson

40-6250

Johnson

40-6250

6657H-A _Manua s 1/28/13 1:45 PM Page 9

7. Technical Specifications

Operation Range -10º to +10º

Axis X axis, Y axis

Resolution 0.002º, 0.01º, 0.1º, 1º

Repeatability < 0.005º (2δ)

Absolute Accuracy (25ºC) < 0.01º(±3º) < 0.04º (±10º)

Temperature Drifting < 1” / ºC (0º) < 1.5” / ºC (±3º)

Response Time < 2S

Operation Temperature 14ºF to 122ºF (-10ºC to +50ºC)

Storage Temperature -4ºF to 140º F (-20ºC to +60ºC)

Weight 1.575 lbs (0.714kg)

Dimension 5.25” x 2.75” x .95”

134mm x 70mm x 24mm

Communication from Electronic Level - Remote Control -

Electronic Level to Bluetooth Output *1 - Cable Output *2

Remote Control or Bluetooth Output *1 -

Cable Output *1 - PC Output *1

Power Supply Remote Control/Receiver: 3 AA batteries

Sensor/Slaver: DC 5V or 3 AA batteries

Range for Bluetooth 32ft (10m)

LCD Backlight Color Green

Battery Life Remote Control/Receiver: 8 hours

Sensor/Slaver: 8 hours

Ro S Compliance, EU Instruction 91/338/EEC,

EU Instruction 94/62/EC, WEEE for EU/EG/EE, Chinese Ro S

6657H-A _Manua s 1/28/13 1:45 PM Page 10

Andere Handbücher für 40-6250

Inhaltsverzeichnis

Sprachen:

Andere Johnson Laser-Nivelliergerät Handbücher

Johnson

Johnson JLX LEVEL UP 40-6681 Bedienungsanleitung

Johnson

Johnson 40-6584 Bedienungsanleitung

Johnson

Johnson 40-6926 Bedienungsanleitung

Johnson

Johnson 40-6028 Bedienungsanleitung

Johnson

Johnson 40-6692 Bedienungsanleitung

Johnson

Johnson 40-6250 Bedienungs- und Wartungsanleitung

Johnson

Johnson 40-0915 Bedienungsanleitung

Johnson

Johnson 40-6065 Bedienungsanleitung

Johnson

Johnson HOT SHOT 9105/40-0910 Bedienungsanleitung

Johnson

Johnson 40-6680 Bedienungsanleitung

Johnson

Johnson 40-6674 Bedienungsanleitung

Johnson

Johnson 1880-2400 Bedienungsanleitung

Johnson

Johnson 40-6551 Bedienungsanleitung

Johnson

Johnson 40-6641 Bedienungsanleitung

Johnson

Johnson 40-6688 Bedienungsanleitung

Johnson

Johnson 40-6060 Bedienungsanleitung

Johnson

Johnson 1888-0700 Bedienungsanleitung

Johnson

Johnson 40-6174 Bedienungsanleitung

Johnson

Johnson 40-6936 Bedienungsanleitung

Johnson

Johnson 40-6650 Bedienungsanleitung

Johnson

Johnson 40-6601 Bedienungsanleitung

Johnson

Johnson 40-6515 Bedienungsanleitung

Johnson

Johnson 9100 Bedienungsanleitung

Johnson

Johnson 40-6502 Bedienungsanleitung

Beliebte Laser-Nivelliergerät Handbücher anderer Marken

Nedo

Nedo ET-5 Bedienungsanleitung

geo-FENNEL

geo-FENNEL Maxi-Liner FL 65 HP Bedienungsanleitung

LaserLiner

LaserLiner X2-Laser Bedienungsanleitung

Spectra

Spectra LL300N Bedienungsanleitung

geo-FENNEL

geo-FENNEL Selection PRO FLG 40-PowerCross GREEN SP Bedienungsanleitung

Nedo

Nedo Crossliner 4 Bedienungsanleitung

Lasertec

Lasertec FX360G Bedienungsanleitung

Flex

Flex ALC 8 Bedienungsanleitung

Black & Decker

Black & Decker LZR5 Bedienungsanleitung

Cocraft

Cocraft HL 20-SG Bedienungsanleitung

Zircon

Zircon iLine Bedienungsanleitung

HWH

HWH 310 SERIES Bedienungsanleitung

Leica

Leica iCON robot 60 Bedienungsanleitung

LaserLiner

LaserLiner SuperCross-Laser SCL 2 Bedienungsanleitung

LaserLiner

LaserLiner ActiveFinder XP Bedienungsanleitung

DeWalt

DeWalt DW082 Bedienungsanleitung

imex

imex EL20 Bedienungsanleitung

Fixturlaser

Fixturlaser NXA D I-0912 Bedienungsanleitung