JONARD TOOLS CMP-1226 Bedienungsanleitung
8 Point Connector Crimp Tool
CMP-1226
MANUAL
The CMP-1226 8 Point Crimp Tool is used for crimping wires (12-26 AWG) and contacts for electrical connectors. The CMP-
1226 is compatible with the M22520/1-01 tool. The CMP-1226 requires a turret head (sold separately to perform the crimping
operation. More info for the Turret Heads (CMP-3) can be found at www.jonard.com.
Before crimping, a positioning or turret head needs to be installed on the CMP-1226 crimping tool. In the installation instructions
below we will be using the Jonard Tools CMP-3 front release turret head.
INSTALLATION INSTRUCTIONS
1. Ensure the Turret is exposed by pressing the Release Leveler on the side of the Turret Head.
2. Insert the Turret Head into the crimper by aligning the pin on the bottom of the Turret Head with the pin hole on the
crimper.
3. Using a hex key, tighten the two captive screws on the top of the Turret Head to lock the head in place.
4. Use the chart below (also on the Turret Head) to determine which position of the selector knob is needed based on the size
of the wire being used:
CONTACT SIZE POSITIONING AND MATING
END COLOR
26 24 22 20 18 16 14 12 WIRE SIZE
20-20 RED 1 2 3 4
SELECTOR NO.
16-22
BLUE
123
16-20* 1 2 3 4
16-16 4
12-16
YELLOW
456
12-12 5 6 7 8
*M39029/1-101 USE RED MATING END COLOR
Pin Hole
Pin needs to be
inserted into hole
Captive
Screws
Release Lever
Turret
CMP-3 Turret Head (sold separately)
CMP-1226 Crimp Tool
Alignment Hole Selector
FEATURES
5. Select the corresponding wire size on the selector knob by aligning the selection number/wire size with the selection arrow
on the left side. To rotate the selector knob, remove the spring lock, pull the knob upward, rotate to the position needed,
and release. Make sure the handles of the crimper are not compressed and the turret is released before rotating the
selector knob.
6. Use the chart on the side of the Turret Head to determine which color insert to select on the turret based on the wire and
contact sizes. For example, if you have a wire size of 22 AWG and a size 20 contact, you will need to rotate the red insert
so that it’s aligned with the white mark on the top of the Turret Head.
Crimped Connector Sectional Views of Crimped Connectors
CONTACT SIZE:
RED: 20
BLUE: 16
YELLOW: 12
7. Push down on the Turret Head until you hear a click.
8. Insert the contact into the back of the crimper, then insert the corresponding wire into the contact. Make sure that the
handles of the crimper are not compressed while doing this.
9. Squeeze the handles together until the ratchet releases. The tool will return to it’s fully open position, and the wire will be
crimped. You can then insert the crimped cable into a connector shell or other desired apparatus.
Inhaltsverzeichnis
Andere JONARD TOOLS Crimpwerkzeuge Handbücher
Beliebte Crimpwerkzeuge Handbücher anderer Marken
Milwaukee
Milwaukee M18 Bedienungsanleitung
HOGERT
HOGERT HT1P169 Bedienungsanleitung
Textron
Textron ESG105L Bedienungsanleitung
Tyco Electronics
Tyco Electronics 90035-3 Bedienungsanleitung
Emerson
Emerson Klauke ES 20RMCCFB Bedienungsanleitung
Continental Refrigerator
Continental Refrigerator PC150HD Bedienungsanleitung