JVC GET0309-001A Bedienungsanleitung

GET0309-001A

[UI]

INSTRUCTIONS

CASSETTE RECEIVER

For installation and connections, refer to the separate manual.

??TH??

KS-FX384

Cover_KS-FX384[UI]f.p65 1/18/05, 9:03 AM1

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to

obtain the best possible performance from the unit.

CONTENTS

SOUND ADJUSTMENTS ................... 10

Adjusting the sound .................................. 10

Turning on/off the super bass function ...... 10

Selecting preset sound modes .................. 11

Storing your own sound adjustments ........ 11

DETACHING THE C0NTROL PANEL ...... 12

CD CHANGER OPERATIONS .............. 13

Playing CDs .............................................. 13

Selecting CD playback modes .................. 14

TROUBLESHOOTING ...................... 15

MAINTENANCE ............................. 16

SPECIFICATIONS ........................... 17

Temperature inside the car....

If you have parked the car for a long time in hot

or cold weather, wait until the temperature in the

car becomes normal before operating the unit.

How to reset your unit ............................... 2

LOCATION OF THE BUTTONS ............ 3

Control panel ............................................. 3

BASIC OPERATIONS ....................... 4

Turning on the power ................................ 4

Setting the clock ........................................ 5

RADIO OPERATIONS ...................... 6

Listening to the radio ................................. 6

Storing stations in memory ....................... 7

Tuning in to a preset station ...................... 8

TAPE OPERATIONS ........................ 9

Listening to a cassette .............................. 9

BEFORE USE

For safety....

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

How to reset your unit

While holding SEL (select), press (standby/on/attenuator) button for more than 2 seconds.

This will reset the built-in microcomputer.

Note:

Your preset adjustments—such as preset channels or sound adjustments—will also be erased.

(standby/on/attenuator)

SEL (select)

EN02-05_KS-FX384[UI]f.p65 1/18/05, 9:05 AM2

LOCATION OF THE BUTTONS

r4/¢buttons

t(control panel release) button

yCD-CH (CD changer) button

Display window

uFM band indicators

FM1, FM2, FM3

iAM band indicator

oCD-CH (CD changer) indicator

;Sound mode indicators

BEAT, SOFT, POP

aTuner reception indicators

MO (monaural), ST (stereo)

sRND (random) indicator

• Used only when connecting to a CD changer.

dS.BASS (super bass) indicator

fMain display

Control panel

1(standby/on/attenuator) button

2S BASS (super bass) button

30(eject) button

4Display window

5Cassette compartment

61/¡PROG (program) button

7SCM (sound control memory) button

8FM AM button

9+/– buttons

pSEL (select) button

qNumber buttons

wMO/RND (monaural/random) button

• Also functions as SSM buttons when pressed

together with DISP (display) button.

• RND (random) functions only when connecting

to a CD changer.

eDISP (display) button

• Also functions as SSM buttons when pressed

together with MO/RND (monaural/random)

button.

Display window

EN02-05_KS-FX384[UI]f.p65 1/18/05, 9:05 AM3

BASIC OPERATIONS

Turning on the power

Turn on the power.

Note on One-Touch Operation:

When you select a source in step

below, the

power automatically comes on. You do not have

to press this button to turn on the power.

Select the source.

To operate the tuner (FM or AM),

see pages 6 – 8.

To play a tape,

see page 9.

To operate the CD changer,

see pages 13 – 14.

To increase the volume

To decrease the volume

Adjust the volume.

Adjust the sound as you want.

(See pages 10 and 11.)

To drop the volume in a moment

Press briefly while listening to any

source. “AT T ”starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press the

button briefly again.

To turn off the power

Press and hold for more than one

second.

“SEE YOU”appears, then the unit turns off.

Volume level appears.

EN02-05_KS-FX384[UI]f.p65 1/18/05, 9:05 AM4

Setting the clock

Press and hold SEL (select) for more

than 2 seconds.

“CLOCK H”or “CLOCK M”

appears on the display.

Set the hour.

1Select “CLOCK H”(hour) if not shown on

the display.

2Adjust the hour.

Set the minute.

1Select “CLOCK M”(minute).

2Adjust the minute.

Finish the setting.

To check the current clock time or change the

display mode

Press DISP (display) repeatedly.

Each time you press the button,

the display mode changes as

follows:

• During tuner operation:

•During tape operation:

• During CD Changer operation:

EN02-05_KS-FX384[UI]f.p65 1/18/05, 9:05 AM5

To stop searching before a station is

received, press the same button you have

pressed for searching.

Searching for a station manually:

Manual search

Select the band (FM1 – 3, AM).

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

an FM broadcast.

Press and hold ¢or 4

until “M” (manual) starts flashing on

the display.

RADIO OPERATIONS

Listening to the radio

You can use either automatic searching or manual

searching to tune in to a particular station.

Note:

When a cassette is in the cassette compartment, you

cannot select the tuner. Be sure to eject the cassette

from the cassette compartment to listen to the radio.

Searching for a station automatically:

Auto search

Select the band (FM1 – 3, AM).

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to

an FM broadcast.

Start searching for a station.

When a station is received, searching stops.

Selected band appears.

Lights up when receiving an FM stereo

broadcast with sufficient signal strength.

To search for stations of

higher frequencies

To search for stations of lower frequencies

EN06-09_KS-FX384[UI]f.p65 1/18/05, 9:05 AM6

To tune in to stations of

higher frequencies

To tune in to stations of lower frequencies

MO (monaural) indicator

Tune in to a station you want while

“M” (manual) is still flashing.

• If you release your finger from the button,

the manual mode will automatically turns

off after 5 seconds.

• If you hold down the button, the frequency

keeps changing (in 50 kHz intervals for

FM and 9 kHz intervals for AM) until you

release the button.

When an FM stereo broadcast is hard to

receive:

Press MO/RND (monaural/random),

while listening to an FM stereo

broadcast.

Each time you press the button, the

MO indicator lights up and goes off

alternately.

When the MO indicator is lit on the display, the

sound you hear becomes monaural but the

reception will be improved.

To restore the stereo effect, press the same

button again.

Storing stations in memory

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM

band (FM1, FM2, and FM3).

Select the FM band (FM1 – 3) you

want to store FM stations into.

Press and hold both buttons for

more than 2 seconds.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2, or FM3).

These stations are preset in the number buttons

—No.1 (lowest frequency) to No.6 (highest

frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

“SSM” appears, then disappears when

automatic preset is over.

EN06-09_KS-FX384[UI]f.p65 1/18/05, 9:05 AM7

Notes:

• A previously preset station is erased when a new

station is stored in the same preset number.

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example,

during battery replacement). If this occurs, preset

the stations again.

Tuning in to a preset station

You can easily tune in to a preset station.

Remember that you must store stations first. If

you have not stored them yet, see “Storing

stations in memory” on pages 7 and 8.

Select the band (FM1 – 3, AM).

Select the number (1 – 6) for the

preset station you want.

Manual preset

You can preset up to 6 stations in each band

(FM1, FM2, FM3, and AM) manually.

Ex.: Storing FM station of 92.5 MHz into the

preset number 1 of the FM1 band.

Select the band (FM1 – 3, AM) you

want to store stations into (in this

example, FM1).

Tune in to a station (in this example,

of 92.5 MHz).

Press and hold the number button

(in this example, 1) for more than

2 seconds.

Repeat the above procedure to store

other stations into other preset

numbers.

Preset number flashes for a while.

To tune in to stations of

higher frequencies

To tune in to stations of lower frequencies

EN06-09_KS-FX384[UI]f.p65 1/18/05, 9:05 AM8

To stop play and eject the cassette

Press 0.

Tape play stops, the cassette automatically

ejects from the cassette compartment. The

source changes to the previously selected one.

• You cannot change the source if the cassette is

still in the cassette compartment.

To change the source, you must eject the

cassette first.

• You can also eject the cassette by pressing 0

while the unit is turned off.

To fast wind a tape

Press in ¡or 1.

The tape will be wound in the direction of the

arrows ( or ).

To restart playback, lightly press the other

button which is not pressed in (1or ¡).

TAPE OPERATIONS

Listening to a cassette

You can play back type I(normal) tapes.

Turn on the power.

Note on One-Touch Operation:

When a cassette is already in the cassette

compartment, tape play starts automatically.

However, it is not recommended to leave the

cassette in the compartment when turning off the

power. It may damage the tape head and the

cassette.

Insert a cassette into the cassette

compartment.

When one side of the tape

reaches its end during

play, the other side of the

tape automatically starts

playing. (Auto Reverse)

Select the tape direction.

Press both buttons at the

same time.

Each time you press both

buttons, the tape direction

changes alternately—

forward ( ) and

reverse ( ).

Tape direction

EN06-09_KS-FX384[UI]f.p65 1/18/05, 9:05 AM9

SOUND ADJUSTMENTS

Adjusting the sound

You can adjust the sound characteristics to your

preference.

Select the item you want to adjust.

Each time you press the

button, the adjustable

items change as follows:

Indication To do: Range

BAS Adjust the bass. –6 (min.)

(Bass) |

+6 (max.)

TRE Adjust the treble. –6 (min.)

(Treble) |

+6 (max.)

FAD*1Adjust the front R6 (Rear only)

(Fader) and rear speaker |

balance. F6 (Front only)

BAL Adjust the left L6 (Left only)

(Balance) and right speaker |

balance. R6 (Right only)

VOL*2Adjust the volume. 00 (min.)

(Volume) |

50 (max.)

*1If you are using a two-speaker system, set the fader

level to “00.”

*2Normally, the + and – buttons work as the volume

control buttons. So you do not have to select “VOL”

to adjust the volume level.

Adjust the level.

Repeat steps

and

to adjust the

other items.

Turning on/off the super bass

function

The super bass function allows you to maintain

the richness and fullness of the bass sound

regardless of how low you set the volume.

Each time you press the

button, the function turns on

and off alternately.

To decrease the level

To increase the level

Ex.: When you select “TRE” (treble)

S.BASS indicator

EN10-13_KS-FX384[UI]f.p65 1/18/05, 9:05 AM10

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JVC Autoempfänger Handbücher

JVC

JVC KD-A845BT Bedienungsanleitung

JVC

JVC KD-ADV5380 Bedienungsanleitung

JVC

JVC EXAD KD-SHX701 Bedienungsanleitung

JVC

JVC KD-AR800 Bedienungsanleitung

JVC

JVC GET0626-001A Bedienungsanleitung

JVC

JVC KD-AR870J Bedienungsanleitung

JVC

JVC KD-AVX11 - EXAD - DVD Player Bedienungsanleitung

JVC

JVC KD-PDR51 Kurzanleitung

JVC

JVC KD-R821BTEY Bedienungsanleitung

JVC

JVC KD-LH1150 Bedienungsanleitung

JVC

JVC KW-NSX1 Leitfaden

JVC

JVC KD-AVX12 Leitfaden

JVC

JVC KD-R401 Leitfaden

JVC

JVC KD-S31J Bedienungsanleitung

JVC

JVC KD-T92MBS Bedienungsanleitung

JVC

JVC KD-R460J Bedienungsanleitung

JVC

JVC KS-FX722R Bedienungsanleitung

JVC

JVC KD-S687 Bedienungsanleitung

JVC

JVC KS-RT650R Bedienungsanleitung

JVC

JVC KD-DV7300J Bedienungsanleitung

JVC

JVC KD-G120 - Radio / CD Player Bedienungsanleitung

JVC

JVC KD-G456 Leitfaden

JVC

JVC KW-R930BTS Bedienungsanleitung

JVC

JVC KD-A95BT Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung