JVC KD-G631E Bedienungsanleitung

SERVICE MANUAL

2007/1

CD RECEIVER

MA29220071SERVICE MANUAL

KD-G631E,KD-G631EX,KD-G631EU,

KD-G631EY,KD-G632E,KD-G632EX,

KD-G632EU,KD-G632EY,KD-G635U,

KD-G635UN,KD-G635UH,KD-G635UT,

KD-G634UI,KD-G638UF

Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)

Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)

TABLE OF CONTENTS

1 PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10

5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

(for europe)

1-2 (No.MA292)

SPECIFICATION

Design and specifications are subject to change without notice.

AUDIO AMPLIFIER SECTION

Maximum Power Output Front/Rear 50 W per channel

Continuous Power Output

(RMS)

Front/Rear 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total har-

monic distortion.

Load Impedance 4 Ω(4 Ωto 8 Ωallowance)

Tone Control Range Bass ±12 dB at 60 Hz

Mid-range ±12 dB at 1 kHz

Treble ±12 dB at 10 kHz

Frequency Response 40 Hz to 20 000 Hz

Signal-to-Noise Ratio 70 dB

Line-Out Level/Impedance 2.5 V/20 kΩload (full scale)

Output Impedance 1 kΩ

Other Terminals CD changer, Steering wheel remote input, USB input jack

TUNER SECTION

Frequency Range FM 87.5 MHz to 108.0 MHz

AM (for europe) MW: 522 kHz to 1 620 kHz

LW: 144 kHz to 279 kHz

AM (for asia) 531 kHz to 1 602 kHz

FM Tuner Usable Sensitivity 11.3 dBf (1.0 µV/75 Ω)

50 dB Quieting Sensitivity 16.3 dBf (1.8 µV/75 Ω)

Alternate Channel Selectivity (400 kHz) 65 dB

Frequency Response 40 Hz to 15 000 Hz

Stereo Separation 30 dB

MW Tuner (for europe) Sensitivity/Selectivity 20 µV/35 dB

LW Tuner (for europe) Sensitivity 50 µV

AM Tuner (for asia) Sensitivity 20 µV

Selectivity 35 dB

CD PLAYER / USB MEMORY SECTION

Type Compact disc player

Signal Detection System Non-contact optical pickup (semiconductor laser)

Number of Channels 2 channels (stereo)

Frequency Response 5 Hz to 20 000 Hz

Dynamic Range 96 dB

Signal-to-Noise Ratio 98 dB

Wow and Flutter Less than measurable limit

MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate : 320 kbps

WMA (Windows Media® Audio) Decoding Format Max. Bit Rate : 192 kbps

Playable USB memory Format FAT 12/16/32

Storage Less than 4 GB (1 partition type)

Playable Audio Format MP3/WMA

Max. Current Less than 500 mA

GENERAL

Power Requirement Operating Voltage DC 14.4 V (11 V to 16 V allowance)

Grounding System Negative ground

Allowable Operating Temperature 0°C to +40°C

Dimensions (W ×H ×D)

(approx.)

Installation Size 182 mm ×52 mm ×150 mm

Panel Size 188 mm ×58 mm ×12 mm

Mass 1.4 kg (excluding accessories)

(No.MA292)1-3

SECTION 1

PRECAUTIONS

1.1 Safety Precautions

!Burrs formed during molding may be left over on some parts of the chassis. Therefore,

pay attention to such burrs in the case of preforming repair of this system.

!Please use enough caution not to see the beam directly or touch it in case of an

adjustment or operation check.

1-4 (No.MA292)

1.2 Preventing static electricity

Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser

diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.

1.2.1 Grounding to prevent damage by static electricity

Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.

Be careful to use proper grounding in the area where repairs are being performed.

(1) Ground the workbench

Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the

traverse unit (optical pickup) on it.

(2) Ground yourself

Use an anti-static wrist strap to release any static electricity built up in your body.

(3) Handling the optical pickup

• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical

pickup are shorted. After replacement, return the shorted parts to their original condition.

(Refer to the text.)

• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily

destroy the laser diode.

1.3 Handling the traverse unit (optical pickup)

(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.

(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the

replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a

time when attaching it to the connector.

(3) Handle the flexible cable carefully as it may break when subjected to strong force.

(4) It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.

1.4 Attention when traverse unit is decomposed

*Please refer to "Disassembly method" in the text for the CD pickup unit.

• Apply solder to the short land before the flexible wire is disconnected from the connector on the CD pickup unit.

(If the flexible wire is disconnected without applying solder, the CD pickup may be destroyed by static electricity.)

• In the assembly, be sure to remove solder from the short land after connecting the flexible wire.

(caption)

Anti-static wrist strap

Conductive material

(conductive sheet) or iron plate

Wires Push switch

Pickup

Base board

Pickup

Connector

Flexible wire

Frame CD mechanism

assembly

(No.MA292)1-5

1.5 Important for laser products

REPRODUCTION AND POSITION OF LABELS and PRINT

WARNING LABEL and PRINT

(No.MA292)1-7

SECTION 3

DISASSEMBLY

3.1 Main body

3.1.1 Removing the Bottom cover

(See Fig.1)

(1) Disengage the five hooks aengaged Bottom cover.

Fig.1

3.1.2 Removing the Front chassis

(See Fig.2)

(1) Remove the two screws A(both side) attaching the Front

chassis.

(2) Disengage the two hooks b(both side) engaged the Front

chassis.

Fig.2

3.1.3 Removing the Rear bracket

(See Fig.3)

(1) Remove the one screw Battaching the remote cable. (only

for Europe models)

(2) Remove the one screw Cattaching the antenna jack.

(3) Remove the one screw Dattaching the LINE OUT jack.

(4) Remove the one screw Eattaching the CD-CH jack.

(5) Remove the one screw Fattaching the IC bracket.

(6) Remove the two screws Gattaching the 16pin connector

jack.

(7) Remove the three screws Hattaching the Rear bracket.

Fig.3

Hook aHook aHook a

Hook b

BEHHH

CD F GG

1-8 (No.MA292)

3.1.4 Removing the Heat sink

(See Fig.4)

(1) Remove the two screws Jand three screws Kattaching the

Heat sink.

Fig.4

3.1.5 Removing the Main board assembly

(See Fig.5)

(1) Remove the three screws Lattaching the Main board as-

sembly.

(2) Disconnect the connector CN501 connected the Main

board assembly and CD board assembly.

Fig.5

3.1.6 Removing the CD mechanism assembly

(See Fig.6)

(1) Remove the three screws Mattaching the CD mechanism

assembly.

Fig.6

JKK

CN501

MMM

(No.MA292)1-9

3.2 Front panel assembly

3.2.1 Removing the Rear cover

(See Fig.7)

(1) Remove the Volume knob from Front panel assembly.

(2) Remove the five screws Nattaching the Rear cover.

(3) Disengage the twelve hooks cengaged Rear cover.

Fig.7

3.2.2 Removing the Switch board assembly

(See Fig.8)

(1) Disengage the illumination lens from Front cover assem-

bly.

(2) Lift up the Switch board assembly and take out it.

CAUTION:

Detach knob and spring are easy to come off, do not lost them.

Fig.8

3.3 CD mechanism assembly

For CD mechanism, please refer mechanism manual TN2007-1010 (No.MY005, No.MY005B).

Hook

illumination lens

1-10 (No.MA292)

SECTION 4

ADJUSTMENT

4.1 Test instruments required for adjustment

(1) Digital oscilloscope (100MHz)

(2) Electric voltmeter

(3) Digital tester

(4) Tracking offset meter

(5) Test Disc JVC: CTS-1000

(6) Extension cable for check

EXTSH002-22P ×1

4.2 Standard measuring conditions

Power supply voltage : DC14.4V(10.5 - 16V)

Load impedance : 20KΩ(2 Speakers connection)

Output Level : Line out 2.0V (Vol. MAX)

4.3 Standard volume position

Balance and Bass & Treble volume : Indication "0"

Loudness : OFF

4.4 Dummy load

Exclusive dummy load should be used for AM, and FM. For FM

dummy load, there is a loss of 6dB between SSG output and an-

tenna input. The loss of 6dB need not be considered since direct

reading of figures are applied in this working standard.

4.5 How to connect the extension cable for adjustment

CAUTION :

Be sure to attach the heat sink and rear bracket onto the

power amplifier and regulator respectively, before supply the

power.

If voltage is applied without attaching those parts, the power

amplifier IC and regulator IC will be destroyed by heat.

Heat sink

Rear bracket

EXTSH002-22P

Extension cable

(No.MA292)1-11

SECTION 5

TROUBLESHOOTING

5.1 16 PIN CORD DIAGRAM (for Europe)

BL/WH

OR/WH

WH/BK

GN/BK

VI/BK

GY/BK

7 RD

16 YL

15 OR/WH

8 BK

6 BL/WH

13 BR

3 GN

11 GN/BK

2 VI

10 VI/BK

12 WH/BK

1 GY

9 GY/BK

RD 7

YL 4

4 WH

NC BR

NC YL

BL/WH

OR/WH

RD BK

VI/BK

GY/BK

WH/BK

GN/BK

Black

Red

Blue

White

Brown

GN Green

VI Violet

GY Gray

YL Yellow

OR Orange

RR Rear Right

FR Front Right

FL Front Left

RL Rear Left

REMOTE

Remote

ILL Illuminations Control

ANT

ACC

TEL

Auto Antenna

ACC Line

Telephone Muting

GND Ground

MEMORY

Memory Backup Battery+

RR+

RR-

RL+

RL-

FL+

FL-

FR+

FR-

ACC

MEMORY

ILL

GND

REMOTE

TEL

Andere Handbücher für KD-G631E

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JVC Autoempfänger Handbücher

JVC

JVC KD-G421 Bedienungsanleitung

JVC

JVC KD-T409 Bedienungsanleitung

JVC

JVC EXAD KW-AVX900 Bedienungsanleitung

JVC

JVC KD-BT11 - Radio / CD Leitfaden

JVC

JVC KD-G240 - MP3 FRONT AUX Handbuch

JVC

JVC KW-M740BT Bedienungsanleitung

JVC

JVC G320 - KD Radio / CD Bedienungsanleitung

JVC

JVC KD-G541 Bedienungsanleitung

JVC

JVC KD-R492M Bedienungsanleitung

JVC

JVC KD-S871R Bedienungsanleitung

JVC

JVC KD-R626 Bedienungsanleitung

JVC

JVC KD-G384 Leitfaden

JVC

JVC KD-S1501 Bedienungsanleitung

JVC

JVC KD-R80BT Bedienungsanleitung

JVC

JVC KD-DB52 Bedienungsanleitung

JVC

JVC KD-LH915 Leitfaden

JVC

JVC KD-SC900R Bedienungsanleitung

JVC

JVC KD-SR72 Bedienungsanleitung

JVC

JVC GET0117-001A Bedienungsanleitung

JVC

JVC KW-XC777 - Radio / CD Bedienungsanleitung

JVC

JVC KD-SX745 Bedienungsanleitung

JVC

JVC KD-R530 Bedienungsanleitung

JVC

JVC KD-R90BT Bedienungsanleitung

JVC

JVC KD-R321 Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung