JVC KD-LH2000R Bedienungsanleitung

SERVICE MANUAL

CD RECEIVER

No.49753

Jun. 2002

KD-LH2000R

Contents

Safety precaution

Preventing static electricity

Important for laser products

Disassembly method

Adjustment method

1-2

1-3

1-4

1-5

1-20

Flow of functional

operation unit TOC read

Maintenance of laser pickup

Replacement of laser pickup

Description of major ICs

1-21

1-23

1-24~51

Area Suffix

EX Continental Europe

Central Europe

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-2

KD-LH2000R

!Burrs formed during molding may be left over on some parts of the chassis. Therefore,

pay attention to such burrs in the case of preforming repair of this system.

Safety precaution

!Please use enough caution not to see the beam directly or touch it in case of an

adjustment or operation check.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-3

KD-LH2000R

CD mechanism

control board

CD mechanism ass’y

Pickup unit

Soldering

Preventing static electricity

1.Grounding to prevent damage by static electricity

Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged,

can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.

2.About the earth processing for the destruction prevention by static electricity

Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as CD players.

Be careful to use proper grounding in the area where repairs are being performed.

2-1 Ground the workbench

Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over

it before placing the traverse unit (optical pickup) on it.

2-2 Ground yourself

Use an anti-static wrist strap to release any static electricity built up in your body.

3. Handling the optical pickup

1. In order to maintain quality during transport and before installation, both sides of the laser diode on the

replacement optical pickup are shorted. After replacement, return the shorted parts to their original condition.

(Refer to the text.)

2. Do not use a tester to check the condition of the laser diode in the optical pickup.The tester's internal power

source can easily destroy the laser diode.

4.Handling the traverse unit (optical pickup)

1. Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.

2. Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup.For specific

details, refer to the replacement procedure in the text. Remove the anti-static pin when replacing the traverse

unit. Be careful not to take too long a time when attaching it to the connector.

3. Handle the flexible cable carefully as it may break when subjected to strong force.

4. It is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it

Attention when traverse unit is decomposed

1.Solder is put up before the card wire is removed from connector on

the CD substrate as shown in Figure.

(When the wire is removed without putting up solder, the CD pick-up

assembly might destroy.)

2.Please remove solder after connecting the card wire with

when you install picking up in the substrate.

*Please refer to "Disassembly method" in the text for pick-up and how to

detach the substrate.

(caption)

Anti-static wrist strap

Conductive material

(conductive sheet) or iron plate

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-4

KD-LH2000R

Important for laser products

1.CLASS 1 LASER PRODUCT

2.DANGER : Invisible laser radiation when open and inter

lock failed or defeated. Avoid direct exposure to beam.

3.CAUTION : There are no serviceable parts inside the

Laser Unit. Do not disassemble the Laser Unit. Replace

the complete Laser Unit if it malfunctions.

4.CAUTION : The compact disc player uses invisible

laserradiation and is equipped with safety switches

whichprevent emission of radiation when the drawer is

open and the safety interlocks have failed or are de

feated. It is dangerous to defeat the safety switches.

5.CAUTION : If safety switches malfunction, the laser is able

to function.

6.CAUTION : Use of controls, adjustments or performance of

procedures other than those specified herein may result in

hazardous radiation exposure.

VARNING : Osynlig laserstrålning är denna del är öppnad

och spårren är urkopplad. Betrakta ej strålen.

VARO : Avattaessa ja suojalukitus ohitettaessa olet

alttiina näkymättömälle lasersäteilylle.Äläkatso

säteeseen.

ADVARSEL : Usynlig laserstråling ved åbning , når

sikkerhedsafbrydere er ude af funktion. Undgå

udsættelse for stråling.

ADVARSEL : Usynlig laserstråling ved åpning,når

sikkerhetsbryteren er avslott. unngåutsettelse

for stråling.

REPRODUCTION AND POSITION OF LABELS

WARNING LABEL

DANGER : Invisibie laser radiation

when open and interlock or

defeated.

AVOID DIRECT EXPOSURE TO

BEAM (e)

VARNING : Osynlig laserstrålning är

denna del är öppnad och spårren är

urkopplad. Betrakta ej strålen. (s)

VARO : Avattaessa ja suojalukitus

ohitettaessa olet alttiina

näkymättömälle lasersäteilylle.Älä

katso säteeseen. (d)

ADVARSEL :Usynlig laserstråling

ved åbning , når

sikkerhedsafbrydere er ude af

funktion. Undgåudsættelse for

stråling. (f)

CLASS 1

LASER PRODUCT

!CAUTION Please use enough caution not to

see the beam directly or touch it

in case of an adjustment or operation

check.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-5

KD-LH2000R

Press the release switch and remove the front panel

unit in the direction of the arrow.

Disassembly method

Removing the front panel unit (See Fig.1)

Turn the body upside down.

Insert a screwdriver to the two joints a and two joints

bon both sides of the body and the joint con the

back of the body, then detach the bottom cover from

the body.

Removing the bottom cover (See Fig.2,3)

When disengaging the joint cusing a

screwdriver, do not damage or break the

board.

CAUTION:

Prior to performing the following procedure, remove

the bottom cover.

Remove the two screws Aattaching the front

chassis.

Remove the two screws B on each side of the body.

Release the two joints dand the two joints eon the

sides. remove the front chassis toward the front.

Removing the front chassis (See Fig.4,5)

Fig.4

Fig.1

Fig. 5

Front panel unit

Front chassis

Joint d

Joint d Joint e

Joint e

Fig. 2

Bottom cover

Joint a

Joint b

Joint c

Fig. 3

Bottom cover

Joint a

Joint b

Joint c

Front chassis

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-6

KD-LH2000R

Remove the four screws C attaching the heat sink

on the left side of the body, and remove the heat

sink.

Removing the heat sink (See Fig.6)

Prior to performing the following procedure, remove

the front chassis, the heat sink, bottom cover and the

rear panel.

Remove the two screws Fattaching the main

amplifier board assembly on the top cover.

Disconnect connector CN601 on the main amplifier

board assembly from the cassette mechanism

assembly.

Removing the main amplifier board assembly

(See Fig.8)

Prior to performing the following procedure, remove

the front chassis, the heat sink and bottom cover.

Remove the six screws D attaching the rear panel

and one screw E attaching the pine jack on the back

of the body.

Removing the rear panel (See Fig.7 )

Heat sink

Fig. 6

Fig. 8

Main board assembly CN601

Fig. 7

Rear panel

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-7

KD-LH2000R

Prior to performing the following procedure, remove

the top cover.

Disconnect the wire from connector CN601on the

MP3 board.

Remove the five screws Gand the MP3 board,

releasing the joint fand g.

Removing the MP3 board (See Fig.9)

Prior to performing the following procedure, remove

the front chassis, the heat sink, bottom cover and the

main amplifier board assembly.

Remove the three screws H attaching the cassette

mechanism assembly from the top cover.

Removing the CD mechanism assembly

(See Fig.10)

Fig.9

CN601

MP3 board

CD mechanism assembly

Top cover

Fig. 10

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-8

KD-LH2000R

Removing the (LCD & key) control switch

board (See Fig.11 ~ 13)

Prior to performing the following procedure, remove

the front panel assembly.

Remove the four screws Iattaching the rear cover

on the back of the front panel assembly.

Unjoint the nine joints hwith the front panel and the

rear cover.

Remove the control switch board on the back of the

front panel.

Fig. 11

Fig. 13

Fig. 12

LCD & Key control board

Joint h

Joint h Joint h

Joint h

Front panel

Rear cover

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-9

KD-LH2000R

Remove the two screws Aon each side of the body.

Lift the front side of the top cover and move the

cover backward to release the two joints a.

Removing the top cover (See Fig.1 and 2)

Remove the screw Bfixing the connector board.

Solder the short-circuit point on the connector board.

Disconnect the flexible wire from the pickup.

Move the connector board in the direction of the

arrow to release the two joints b.

Unsolder the wire on the connector board if

necessary.

Removing the connector board

(See Fig.3 to 5)

Before disconnecting the flexible wire

from the pickup, solder the short-circuit

point on the pickup. No observance of

this instruction may cause damage of

the pickup.

CAUTION:

Unsolder the short-circuit point after

reassembling.

CAUTION:

Fig.1

Fig.2

Fig.3

Fig.4Fig.5

Joints a

Top cover

Connector board

DET switch

Pickup

Short-circuit

Joints b

Short-circuit point

(Soldering)

Flexible wire

Connector board

Frame

< CD mechanism section >

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-10

KD-LH2000R

Extend the two tabs cof the feed sw. holder and pull

out the switch.

Unsolder the DET switch wire if necessary.

Removing the DET switch

(See Fig.3 and 6)

Prior to performing the following procedure, remove

the top cover and the connector board.

Remove the two suspension springs (L) and (R)

attaching the chassis unit to the frame.

Removing the chassis unit

(See Fig.7 and 8)

The shape of the suspension spring (L)

and (R) are different. Handle them with

care.

CAUTION:

When reassembling, make sure that the

three shafts on the underside of the

chassis unit are inserted to the dampers

certainly.

CAUTION:

Fig.3

Fig.6

Fig.8Fig.7

Connector board

DET switch

Pickup

Short-circuit

Joints b

Tab c

Feed sw. holder

Tab c

Suspension spring (L)

Suspension spring (R)

Chassis unit

Frame

Shafts

Shaft

Damper

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

Andere Handbücher für KD-LH2000R

Inhaltsverzeichnis

Andere JVC Autoempfänger Handbücher

JVC

JVC EXAD KD-LHX551 Leitfaden

JVC

JVC KD-AR400 Bedienungsanleitung

JVC

JVC KW-XG500J, KW-XG504UI Bedienungsanleitung

JVC

JVC KW-AVX716 Bedienungsanleitung

JVC

JVC KD-LX50R Bedienungsanleitung

JVC

JVC KW-TC410 Bedienungsanleitung

JVC

JVC KD-AVX40 - DVD Player With LCD monitor Leitfaden

JVC

JVC KD-HDR61 Bedienungsanleitung

JVC

JVC KD-G120 - Radio / CD Player Administratorhandbuch

JVC

JVC KD-AR5500 Bedienungsanleitung

JVC

JVC KD-R901 Bedienungsanleitung

JVC

JVC KD-DV4406 Bedienungsanleitung

JVC

JVC KD-R890BT Bedienungsanleitung

JVC

JVC KD-R801 Leitfaden

JVC

JVC KD-G425 Bedienungsanleitung

JVC

JVC KD-BT11 - Radio / CD Leitfaden

JVC

JVC KD-DV4406 Leitfaden

JVC

JVC KD-MX3000J Bedienungsanleitung

JVC

JVC KD-S656R Bedienungsanleitung

JVC

JVC KS-FX210 Leitfaden

JVC

JVC KD-R80BT Bedienungsanleitung

JVC

JVC GET0140-001A Bedienungsanleitung

JVC

JVC KDA605 - KD Radio / CD Leitfaden

JVC

JVC KD-R681 Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung