JVC KD-S680 Bedienungsanleitung

ENGLISH

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

GET0058-001A

[J]

ESPAÑOL

FRANÇAIS

For customer Use:

Enter below the Model No. and

Serial No. which are located on

the top or bottom of the cabinet.

Retain this information for future

reference.

Model No.

Serial No.

For installation and connections, refer to the separate manual.

Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, se référer au manuel séparé.

COMPACT

DIGITAL AUDIO

KD-S7250/KD-S700/

KD-S680

CD RECEIVER

RECEPTOR CON CD

RECEPTEUR CD

KD-S7250

KD-S700

KD-S680

KD-S7250

KD-S700

RM-RK31

KD-S680

RM-RK31

COVER KD-S7250/700/680[J] 26/10/01, 8:44 AM3

ENGLISH

How to reset your unit

Press and hold both the SEL (Select) and

(Standby/On/ATT) buttons at the same time for several

seconds.

This will reset the built-in microcomputer.

NOTES: Your preset adjustments — such as preset channels

or sound adjustments — will also be erased.

If a CD is in the unit, it will eject when you reset the

unit. Pay attention not to drop the CD.

IMPORTANT FOR LASER PRODUCTS

Precautions:

1. CLASS 1 LASER PRODUCT

2. CAUTION: Invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure

to beam.

3. CAUTION: Do not open the top cover. There are no user-serviceable parts inside. Leave all servicing

to qualified service personnel.

4. CAUTION: This CD player uses invisible laser radiation, however, is equipped with safety switches to

prevent radiation emission when unloading CDs. It is dangerous to defeat the safety switches.

5. CAUTION: Use of controls, adjustments or performance of procedures other than those specified

herein may result in hazardous radiation exposure.

SEL (Select)

(Standby/On/ATT)

INFORMATION (For USA)

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one

or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

EN02-03 KD-S7250/700/680[J] 26/10/01, 9:07 AM2

ENGLISH

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

CONTENTS

BEFORE USE

*For safety....

• Do not raise the volume level too much, as this

will block outside sounds, making driving

dangerous.

• Stop the car before performing any complicated

operations.

*Temperature inside the car....

If you have parked the car for a long time in hot

or cold weather, wait until the temperature in the

car becomes normal before operating the unit.

How to reset your unit ................................. 2

LOCATION OF THE BUTTONS .............. 4

Control panel .................................................. 4

Remote controller ........................................... 5

Preparing the remote controller ...................... 6

BASIC OPERATIONS ......................... 7

Turning on the power ..................................... 7

RADIO BASIC OPERATIONS ................ 8

Listening to the radio ......................................

Storing stations in memory ............................. 9

Tuning into a preset station .......................... 10

Other convenient tuner functions ................. 10

CD OPERATIONS ............................11

Playing a CD ................................................ 11

Locating a track or a particular portion

on a CD .................................................... 12

Selecting CD playback modes ...................... 12

Prohibiting CD ejection ................................. 13

SOUND ADJUSTMENTS .................... 14

Adjusting the sound ...................................... 14

Turning on/off the loudness function ............ 14

Using the Sound Control Memory (SCM) ..... 14

Storing your own sound adjustments ........... 16

OTHER MAIN FUNCTIONS ................. 17

Setting the clock ........................................... 17

To Cancel Advanced SCM ........................... 1

Selecting the level display ............................ 1

Detaching the control panel .......................... 19

MAINTENANCE ..............................20

Handling CDs ............................................... 20

TROUBLESHOOTING ....................... 21

SPECIFICATIONS ............................ 22

EN02-03 KD-S7250/700/680[J] 26/10/01, 9:07 AM3

ENGLISH

riu

5 6

1 2 789 p

oag

d; sf

hjk l

LOCATION OF THE BUTTONS

Control panel

Display window

1(standby/on/attenuator) button

2Control dial

3LOUD (loudness) button

4DISP (display) button

5Display window

6Loading slot

7CD button

8FM button

90(eject) button

p4/¢buttons

•

Also functions as SSM buttons when pressed

together.

qSEL (select) button

wRemote sensor

eNumber buttons

rSCAN button

RPT (repeat) button

tMO (monaural) button

RND (random) button

ySCM (sound control memory) button

uAM button

i(control panel release) button

Display window

oVolume (or audio) level indicator

Equalization Pattern indicator

;Tuner reception indicators

MO (monaural), ST (stereo)

aRND (random) indicator

sRPT (repeat) indicatior

d“SCM” indicator

fLOUD indicator

gSound mode indicators

BEAT, SOFT, POP

hCD indicator

jBand indicators

FM1, FM2, FM3

kMain display

lCD-in indicator

EN04-06 KD-S7250/700/680[J] 26/10/01, 8:50 AM4

ENGLISH

RM-RK31

3•Functions as the PRESET button while

listening to the radio.

Each time you press the button, the preset

station number increases, and the selected

station is tuned into.

•Does not function as the DISC –button.

4Functions the same as the control dial on the

main unit.

NOTE:

These buttons cannot be used for the clock

(CLOCK H, CLOCK M), SCM LINK and

LEVEL (see pages 17 and 18).

5Selects the sound mode.

Each time you press the button, the mode

changes.

6Selects the source.

Each time you press the button, the source

changes.

7•Searches stations while listening to the radio.

•Fast-forwards or reverses the track if pressed

and held while listening to a CD.

•Skips to the beginning of the next track or goes

back to the beginning of the current (or

previous tracks) if pressed briefly while

listening to a CD.

Remote controller

1•Turns on the unit if pressed when the unit is

turned off.

•Turns off the unit if pressed and held until “SEE

YOU”appears on the display.

•Drops the volume level in a moment if pressed

briefly.

Press again to resume the volume.

2•Functions as the BAND button while listening

to the FM broadcast.

Each time you press the button, the band

changes.

•Does not function as the PROG/DISC

+ button.

EN04-06 KD-S7250/700/680[J] 26/10/01, 8:50 AM5

ENGLISH

Preparing the remote

controller

Before using the remote controller:

•Aim the remote controller directly at the remote

sensor on the main unit. Make sure there is no

obstacle in between.

•Do not expose the remote sensor to strong light

(direct sunlight or artificial lighting).

Installing the battery

When the controllable range or effectiveness

of the remote controller decreases, replace

the battery.

1. Remove the battery holder.

1) Push out the battery holder in the

direction indicated by the arrow using a

ball point pen or a similar tool.

2) Remove the battery holder.

2. Place the battery.

Slide the battery into the holder with the

+ side facing upwards so that the battery

is fixed in the holder.

Remote sensor

(back side)

3. Return the battery holder.

Insert again the battery holder pushing it

until you hear a clicking sound.

WARNING:

• Store the batteries in a place which children

cannot reach.

If a child accidentally swallows the battery,

immediately consult a doctor.

• Do not recharge, short, disassemble or heat the

batteries or dispose of in a fire.

Doing any of these things may cause the

batteries to give off heat, crack or start a fire.

• Do not leave the batteries with other metallic

materials.

Doing this may cause the batteries to give off

heat, crack or start a fire.

• When throwing away or saving the batteries,

wrap in tape and insulate; otherwise, it may

cause the batteries to give off heat, crack or

start a fire.

• Do not poke the batteries with tweezers or

similar tools.

Doing this may cause the batteries to give off

heat, crack or start a fire.

Lithium coin battery

(product number:

CR2025)

EN04-06 KD-S7250/700/680[J] 26/10/01, 8:50 AM6

ENGLISH

BASIC OPERATIONS

Adjust the sound as you want (see

pages 14 – 16).

To drop the volume in a moment

Press briefly while listening to any

source. “ATT” starts flashing on the display, and

the volume level will drop in a moment.

To resume the previous volume level, press the

button briefly again.

• If you turn the control dial clockwise, you can

also restore the sound.

To turn off the power

Press and hold until “SEE YOU”appears

on the display.

Note:

When you use this unit for the first time, set the built-in

clock correctly, see page 17.

CAUTION on Volume Setting:

CDs produce very little noise compared with other

sources. If the volume level is adjusted for the

tuner, for example, the speakers may be damaged

by the sudden increase in the output level.

Therefore, lower the volume before playing a disc

and adjust it as required during playback.

To increase the volume.

Volume level appears

To decrease the volume.

Turning on the power

Turn on the power.

Note on One-Touch Operation:

When you select a source in step 2 below, the power

automatically comes on. You do not have to press

this button to turn on the power.

Select the source.

To operate the tuner (FM or AM),

see pages 8 –10.

To operate the CD player,

see pages 11 –13.

Adjust the volume.

Volume or audio level (see page 18) indicator

EN07 KD-S7250/700/680[J] 26/10/01, 8:49 AM7

ENGLISH

RADIO BASIC OPERATIONS

To stop searching before a station is received,

press the same button you have pressed for

searching.

Searching a station manually:

Manual search

Select the band (FM1 – 3, AM).

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

Press and hold ¢or 4until

"M"(manual) starts flashing on the

display.

Listening to the radio

You can use either automatic searching or manual

searching to tune into a particular station.

Searching a station automatically:

Auto search

Select the band (FM1 – 3, AM).

Note:

This receiver has three FM bands (FM1, FM2,

FM3). You can use any one of them to listen to an

FM broadcast.

Start searching a station.

When a station is received, searching

stops.

Press ¢to search

stations of higher

frequencies.

Press 4to search

stations of lower

frequencies.

FM1 FM2 FM3

Selected band appears.

FM1 FM2 FM3

Selected band appears.

Audio (see page 18) or volume level

indicator

EN08-10 KD-S7250/700/680[J] 26/10/01, 8:49 AM8

ENGLISH

Tune into a station you want while“M”

is flashing.

• If you release your finger from the button,

the manual mode will automatically turn off

after 5 seconds.

• If you hold down the button, the frequency

keeps changing.

When an FM stereo broadcast is hard to

receive:

Press MO RND (monaural/random) while listening

to an FM stereo broadcast.

• Each time you press the button, the MO indicator

lights up and goes off alternately.

When the MO indicator is lit on the display, the

sound you hear becomes monaural but the

reception will be improved (the ST indicator goes

off).

To restore the stereo effect, press the same button

again.

Storing stations in memory

You can use one of the following two methods to

store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong-

station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM band

(FM1, FM2 and FM3).

Select the FM band (FM1 –3) you want

to store FM stations into.

• Each time you press the button, the FM

band changes as follows:

Press and hold both buttons for more

than 2 seconds.

Local FM stations with the strongest signals are

searched and stored automatically in the band

number you have selected (FM1, FM2 or FM3.)

These stations are preset in the number buttons —

No.1 (lowest frequency) to No.6 (highest

frequency).

When automatic preset is over, the station stored

in number button 1 will be automatically tuned in.

Lights up when receiving an

FM broadcast in stereo.

Press ¢to search

stations of higher

frequencies.

Press 4to search

stations of lower

frequencies.

“SSM” appears, then disappears when automatic

preset is over.

FM1 FM2 FM3

EN08-10 KD-S7250/700/680[J] 26/10/01, 8:49 AM9

ENGLISH

Manual preset

You can preset up to 6 stations in each band (FM1,

FM2, FM3 and AM) manually.

Ex: Storing an FM station of 88.3 MHz into the

preset number 1 of the FM1 band

Select the band (FM1 –3, AM) you

want to store FM stations into (in

this example, FM1).

• Each time you press the button, the FM

band changes as follows:

Tune into a station of 88.3 MHz.

Press and hold the number button (in

this example, 1) for more than 2

seconds.

Repeat the above procedure to store

other stations into other preset

numbers.

Notes:

• A previously preset station is erased when a new station

is stored in the same preset number.

• Preset stations are erased when the power supply to

the memory circuit is interrupted (for example, during

battery replacement). If this occurs, preset the stations

again.

Tuning into a preset station

You can easily tune into a preset station.

Remember that you must store stations first. If you

have not stored them yet, see “Storing stations in

memory” on page 9 and 10.

Select the band (FM1 –3, AM).

Select the number (1 –6) for the preset

station you want.

Other convenient tuner

functions

Scanning broadcast stations

When you press RPT SCAN while listening to the

radio, station scanning starts. Each time a

broadcast is tuned in, scanning stops for about 5

seconds (tuned frequency number flashes on the

display), and you can check what program is now

being broadcasted.

If you want to listen to that program, press the same

button again to stop scanning.

Press ¢to tune in

stations of higher

frequencies.

Press 4to tune in

stations of lower

frequencies.

“P1” flashes for a few

seconds.

FM1 FM2 FM3

EN08-10 KD-S7250/700/680[J] 26/10/01, 8:49 AM10

Andere Handbücher für KD-S680

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere JVC Autoempfänger Handbücher

JVC

JVC KD-T905BTS Bedienungsanleitung

JVC

JVC KD-R720 Bedienungsanleitung

JVC

JVC KD-S743R Bedienungsanleitung

JVC

JVC KW-XR611 Bedienungsanleitung

JVC

JVC KD-G335 Bedienungsanleitung

JVC

JVC KWAVX800 - EXAD - DVD Player Leitfaden

JVC

JVC KD-G301 Leitfaden

JVC

JVC KS-FX621 Leitfaden

JVC

JVC GET0143-001A Bedienungsanleitung

JVC

JVC KD-LX330R Bedienungsanleitung

JVC

JVC KD-S71R Bedienungsanleitung

JVC

JVC KD-SX911R Bedienungsanleitung

JVC

JVC KD-G735 Leitfaden

JVC

JVC KW-R520M Bedienungsanleitung

JVC

JVC CDA-5755 Bedienungsanleitung

JVC

JVC GET0114-001A Bedienungsanleitung

JVC

JVC KD-DV4401 Bedienungsanleitung

JVC

JVC KD-AR870J Bedienungsanleitung

JVC

JVC EXAD KD-AVX44 Bedienungsanleitung

JVC

JVC Pandora KD-A925BT Bedienungsanleitung

JVC

JVC KD-S700 Technisches Handbuch

JVC

JVC KS-F345 Bedienungsanleitung

JVC

JVC KS-FX460R Bedienungsanleitung

JVC

JVC KD-AVX1 Bedienungsanleitung

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung