JVC KD-SV3704 Bedienungsanleitung

For installation and connections, refer to the separate manual.

INSTRUCTIONS

LVT1954-001A

[UI]

VCD/CD RECEIVER

KD-SV3704

EN_KD-SV3704[UI].indb 1EN_KD-SV3704[UI].indb 1 08.12.12 2:33:23 PM08.12.12 2:33:23 PM

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best

possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to

qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical

instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

[European Union only]

Warning:

If you need to operate the unit while driving, be sure to

look around carefully or you may be involved in a traffic

accident.

For safety...

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold

weather, wait until the temperature in the car becomes

normal before operating the unit.

Caution on volume setting:

Discs produce very little noise compared with other

sources. Lower the volume before playing a disc to

avoid damaging the speakers by the sudden increase of

the output level.

To prevent accidents and damage

• DO NOT install any unit in locations where;

– it may obstruct the steering wheel and

gearshift lever operations.

– it may obstruct the operation of safety

devices such as air bags.

– it may obstruct visibility.

• DO NOT operate the unit while driving.

• If you need to operate the unit while

driving, be sure to look around carefully.

• The driver must not watch the monitor

while driving.

If the parking brake is not engaged,

“PARKING” flashes on the display, and

no playback picture will be shown on the

monitor.

– This warning appears only when the

parking brake wire is connected to the

parking brake system built in the car

(refer to the Installation/Connection

Manual).

EN_KD-SV3704[UI].indb 2EN_KD-SV3704[UI].indb 2 08.12.12 2:33:26 PM08.12.12 2:33:26 PM

CONTENTS

Detaching/attaching control panel .............. 3

How to reset your unit ................................. 3

OPERATIONS

Basic operations........................................... 4

• Using the control panel............................... 4

• Using the remote controller (RM-RK121).... 5

• Changing the display information .............. 7

Preparation.................................................. 7

Listening to the radio................................... 8

Disc operations............................................. 9

Listening to the other external components

... 14

SETTINGS

Sound and monitor settings......................... 15

REFERENCES

More about this unit .................................... 16

Troubleshooting........................................... 18

Maintenance................................................ 20

Specifications............................................... 21

Detaching/attaching control panel

Detaching...

Attaching...

How to reset your unit

• Your preset adjustments will also be erased.

In this manual, operations using the control panel

are mainly explained; however, you can use the

buttons and controls on the remote control if they

have the same (or similar) name and marks.

EN_KD-SV3704[UI].indb 3EN_KD-SV3704[UI].indb 3 08.12.12 2:33:26 PM08.12.12 2:33:26 PM

Basic operations

Using the control panel

67 89p

o; sadwe tryuiq

12345

tActivate/deactivate the loudness setting.

yPreset the station automatically [Hold].

uPlays/pauses.

iChange playback mode—INT, RPT, RND.

o• Select preset station.

• Preset a station manually [Hold].

;Change the color system.

aChange the VCD audio channel.

sAUX (auxiliary) input jack

dChange the tuner reception mode.

• Select stereo or monaural reception.

• Select local or distance-extreme reception

[Hold].

*1While the sound is attenuated, no operations are

available. To operate the unit, deactivate the sound

attenuation by pressing ATT again.

*2You cannot select this source if no disc is inserted.

1Select folder.

2• Turn on the power.

• Turn off the power.

3Select the FM/AM band.

4• Control the volume or select items [Turn].

• Confirm the selection.

• Adjust the sound settings.

5Remote sensor

6Loading slot

7Display window

8Eject disc.

9Attenuate the sound.*1

p• Change the display information.

• Enters the clock setting mode [Hold].

qDetach the panel.

wSelect the source.

Tuner =Disc*2=AUX IN =(back to the

beginning)

e• Tuner: Search for station.

• Disc: Select track.

rSelect the sound mode.

EN_KD-SV3704[UI].indb 4EN_KD-SV3704[UI].indb 4 08.12.12 2:33:27 PM08.12.12 2:33:27 PM

5OPERATIONS

Before using the remote controller:

• Aim the remote controller directly at the remote

sensor on the unit.

• DO NOT expose the remote sensor to bright light

(direct sunlight or artificial lighting).

Installing the lithium coin battery (CR2025)

Caution:

• Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

• Battery shall not be exposed to excessive heat such as

sunshine, fire, or the like.

If the effectiveness of the remote controller

decreases, replace the battery.

Display window

1Preset number / track (F), folder (d) indication

2Tuner reception indicators—ST (stereo), MONO

(monaural)

3LOUD (loudness) indicator

4Playback mode indicators—INT (intro),

RPT (repeat), RND (random)

5LO (local) indicator

6Disc type—CD, MP3, VCD

7Tr (track) indicator

8Main display

9EQ (equalizer) indicator and sound mode

indicators—ROCK, POPS, CLASSIC, FLAT

Using the remote controller (RM-RK121)

Continued on the next page

Remote sensor

12 3 4 5

67 98

EN_KD-SV3704[UI].indb 5EN_KD-SV3704[UI].indb 5 08.12.12 2:33:27 PM08.12.12 2:33:27 PM

1Attenuate the sound.

2• Turn on the power.

• Turn off the power.

3Play repeatedly.

4Turn on and off the OSD (On-Screen Display) on the

monitor.

5• Audio CD/VCD: Select a track.

• VCD: Select the desired position.

6Make selection/settings.

7• Play/pause.

• Confirm the selection.

8• Tuner: Select the FM/AM band.

• VCD: Change the color system.

9Select the sound mode.

pSelect the sound setting item.

q• Enter numbers. (See also “How to use number

buttons” on the right column.)

• Tuner:

– Select preset station (1 – 6).

– Preset a station manually (1 – 6) [Hold].

wActivate/deactivate the PBC (Playback Control)

function.

eSelect the source.

Tuner =Disc * =AUX IN =(back to the

beginning)

rChange the VCD audio channel.

t• Adjust the volume level.

• Adjust the sound settings.

yActivate/deactivate the loudness setting.

uStop playback.

i• Tuner: Search for station.

• Disc: Select track.

oReverse/Forward search.

;Display the program screen.

*You cannot select this source if no disc is inserted.

Warning (to prevent accidents and damage):

• Do not install any battery other than CR2025 or its

equivalent.

• Do not leave the remote controller in a place (such

as dashboards) exposed to direct sunlight for a long

time.

• Store the battery in a place where children cannot

reach.

• Do not recharge, short, disassemble, heat the battery,

or dispose of it in a fire.

• Do not leave the battery with other metallic

materials.

• Do not poke the battery with tweezers or similar

tools.

• Wrap the battery with tape and insulate when

throwing away or saving it.

;

How to use number buttons

• For selecting track number/item number on PBC

menu:

To select 5:

To select 15: ==

To select 125:

====

• For selecting program number and specifying

time to start playback:

To select 5:

To select 15: =

EN_KD-SV3704[UI].indb 6EN_KD-SV3704[UI].indb 6 08.12.12 2:33:28 PM08.12.12 2:33:28 PM

7OPERATIONS

Preparation

Setting the clock

On the Unit ONLY:

1Turn on the power.

2Change the source to tuner.

Press the button repeatedly until the tuner frequency is

displayed.

[Turn] =[Press]

[Hold] Adjust the hour.

[Turn]

Adjust the minute.

• You can go back to the adjustment of the hour by pressing the

button.

5Finish the procedure.

• To display the clock, press DISP repeatedly until the clock is displayed (see “Changing the display information”

above).

Changing the display information

On the Unit ONLY:

• When the power is turned on: The display information of the current source changes as follows:

Tuner Frequency and the band (F1, F2, F3, A1 or A2) =Clock =(back to the beginning)

Disc • Audio CD/WMA/VCD:

Current track number with the elapsed playing time =Clock =(back to the beginning)

• MP3:

Album name/performer (folder name)* =Track title (file name)* =Current track number

with the elapsed playing time =Clock =(back to the beginning)

AUX IN Source name (AUX IN) =Clock =(back to the beginning)

*If an MP3 le does not have Tag information, folder name and le name appear.

EN_KD-SV3704[UI].indb 7EN_KD-SV3704[UI].indb 7 08.12.12 2:33:28 PM08.12.12 2:33:28 PM

Listening to the radio

1Change the source to tuner.

Press the button repeatedly until the tuner frequency is displayed.

2Select the band.

F(FM) 1 F2 F3

A(AM) 1

3Search for a station to listen—Auto Search.

When a station is tuned in, searching stops. To stop searching, press the same

button again.

• You can also search a station manually—Manual Search. Hold either one of

the buttons until “M” appears on the display, then press it repeatedly.

• When receiving an FM stereo broadcast with sufficient signal strength, the ST

indicator lights up on the display.

Improving the FM reception

When an FM stereo broadcast is hard to receive,

activate monaural mode for better reception.

On the Unit ONLY:

Reception improves, but stereo effect will be lost.

• The MONO indicator lights up on the display.

To restore the stereo effect, repeat the same

procedure to select “MONO OFF.” The MONO

indicator goes off.

To tune in FM stations only with

strong signals—LO/DX (Local/

Distance-extreme)

If received signals are weak, you may only hear

noises. You can make this unit detect only stations

with sufficient signal strength while searching for FM

stations.

On the Unit ONLY:

Only stations with sufficient signal strength will be

detected.

• The LO indicator lights up on the display.

To tune in to all receivable stations, repeat the

same procedure to select “DX.”

• The LO indicator goes off.

MONO ON

LOCAL

[Hold]

EN_KD-SV3704[UI].indb 8EN_KD-SV3704[UI].indb 8 08.12.12 2:33:29 PM08.12.12 2:33:29 PM

9OPERATIONS

Storing stations in memory

You can preset 6 stations for each band.

Automatic presetting —SSM (Strong-station

Sequential Memory)

On the Unit ONLY:

1Select the band you want to store into.

Local stations with the strongest signals are searched

and stored automatically.

[Hold]

Manual presetting

Ex.: Storing FM station of 92.50 MHz into preset number

“4.”

1Tune in to the station you want to preset.

Selecting preset station

Disc operations

1Turn on the power.

2Insert a disc.

All tracks will be played repeatedly until you change the source or eject

the disc.

• If a disc menu appears on the monitor while playing a VCD with PBC,

see page 10.

Before performing any operations, make sure the following...

• Turn on the monitor and select the appropriate monitor input before playing a VCD.

• If you turn on the monitor, you can also control the MP3/WMA playback by referring to the monitor screen

(see page 12).

• Select the color system suitable for your monitor (see page 15).

F(FM) 1 F2 F3

A(AM) 1

[Hold]

92.50 F1

Preset number

EN_KD-SV3704[UI].indb 9EN_KD-SV3704[UI].indb 9 08.12.12 2:33:29 PM08.12.12 2:33:29 PM

Selecting a track

On the Unit:

On the Remote:

• For audio CD, MP3 disc* or VCD without PBC only

• For details about using number buttons, see page 6.

• You can also use 4/ ¢to select a track.

*You can specify the tracks in the current folder.

Selecting the next or previous folders (only

for MP3 or WMA discs)

• For MP3/WMA discs, see also “MP3/WMA control

screen operations” on page 12.

Playback Control (PBC) operations

On the Remote ONLY:

1While playing a VCD...

The current setting is shown on the monitor.

ON: You can play the disc interactively using

the menu.

OFF: Cancels.

• A menu may be a list of items, submenus, or

some moving pictures.

Stop playing and ejecting the disc

On the Unit ONLY:

The disc is ejected and the source is changed to the

previous source.

Stop playing

On the Remote ONLY:

• The unit memorizes the position where the playback

has been stopped, and when you start playback again

by pressing 6, it starts from the position where

you have stopped—Resume Play.

To clear the memorized position, press 7twice.

Pause playing

• Press the button again to start playback.

Fast-forwarding or reversing the track

On the Unit:

On the Remote:

[Hold]

OFF

EN_KD-SV3704[UI].indb 10EN_KD-SV3704[UI].indb 10 08.12.12 2:33:30 PM08.12.12 2:33:30 PM

Andere Handbücher für KD-SV3704

Inhaltsverzeichnis

Andere JVC Autoempfänger Handbücher

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung