JVC Serial No. Bedienungsanleitung

ENGLISHESPAÑOLFRANÇAIS

CD RECEIVER

RECEPTOR CON CD

RÉCEPTEUR CD

For canceling the display demonstration, see page 7.

Para cancelar la demostración en pantalla, consulte la página 7.

Pour annuler la démonstration des affichages, référez-vous à la page 7.

For installation and connections, refer to the separate manual.

Para la instalación y las conexiones, refiérase al manual separado.

Pour l’installation et les raccordements, se référer au manuel séparé.

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

GET0576-001A

[J]

For customer Use:

Enter below the Model

No. and Serial No. which

are located on the top or

bottom of the cabinet. Retain

this information for future

reference.

Model No.

Serial No.

KD-R400

Cover_KD-R400[J]_f.indd 1Cover_KD-R400[J]_f.indd 1 9/10/08 3:35:50 PM9/10/08 3:35:50 PM

ENGLISH

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best

possible performance from the unit.

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Caution:

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to

qualified service personnel.

3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.

(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with

optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

[European Union only]

Warning:

If you need to operate the unit while driving, be sure to

look around carefully or you may be involved in a traffic

accident.

For safety...

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold

weather, wait until the temperature in the car becomes

normal before operating the unit.

EN02-09_KD-R400[J]_f.indd 2EN02-09_KD-R400[J]_f.indd 2 9/10/08 3:33:21 PM9/10/08 3:33:21 PM

ENGLISH

How to reset your unit

• Your preset adjustments will also be erased.

How to forcibly eject a disc

• You can forcibly eject the loaded disc even if the disc is

locked. To lock/unlock the disc, see page 9.

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

CONTENTS

Detaching the control panel......................... 3

Attaching the control panel ......................... 3

How to reset your unit ................................. 3

How to forcibly eject a disc........................... 3

OPERATIONS

Basic operations........................................... 4

• Using the control panel............................... 4

• Using the remote controller (RM-RK50)...... 6

Preparation.................................................. 7

Listening to the radio................................... 8

Disc operations............................................. 9

Listening to the USB device.......................... 10

EXTERNAL DEVICES

Listening to the other external

components.............................................. 11

SETTINGS

Selecting a preset sound mode .................... 12

Title assignment .......................................... 13

Menu operations.......................................... 14

Color settings............................................... 17

REFERENCES

More about this unit .................................... 18

Troubleshooting........................................... 21

Maintenance................................................ 23

Specifications............................................... 24

Detaching the control panel

Attaching the control panel

Caution on volume setting:

Digital devices (CD/USB) produce very little noise

compared with other sources. Lower the volume before

playing these digital sources to avoid damaging the

speakers by sudden increase of the output level.

This mark is used to indicate...

Turn the control dial to make a

selection, then press to confirm the

selection.

EN02-09_KD-R400[J]_f.indd 3EN02-09_KD-R400[J]_f.indd 3 14/10/08 2:33:01 PM14/10/08 2:33:01 PM

ENGLISH

Basic operations

Using the control panel

9Select the sound mode.

pDetach the panel.

qChange the display information.

w• FM/AM: Search for station.

• CD/USB: Select track.

eReturn to the previous menu.

rRemote sensor

tAUX (auxiliary) input jack

yUSB (Universal Serial Bus) input jack

*1Also known as “Control dial” in this manual.

*2You cannot select these sources if they were disabled

in the Menu (see “SRC SELECT” in “Menu

operations” on page 16).

*3You cannot select “CD” as the playback source if no

disc is in the unit.

*4You can still adjust the volume during pause when

the selected source is CD/USB.

Before resume playback, check to be sure that you

have not raise the volume level too much.

1• FM/AM: Select preset station.

• CD/USB: Select folder.

2• Turn on the power.

• Attenuate the sound (if the power is on).

• Turn off the power [Hold].

3Select the source.

FM =AM*2=CD*3=USB =AUX IN*2=

(back to the beginning)

4• Enter list operations.

• Enter Menu setting [Hold].

5• Control the volume*4or select items [Turn].

• Confirm the selection [Press].

• FM: Enter SSM preset mode [Hold].

• CD/USB: Enter playback mode [Hold].

Pause/resume playback*4[Press].

6Loading slot

7Display window

8Eject disc.

You can change the display and button illumination (see “COLOR” on page 15).

EN02-09_KD-R400[J]_f.indd 4EN02-09_KD-R400[J]_f.indd 4 9/10/08 3:33:26 PM9/10/08 3:33:26 PM

ENGLISH

5OPERATIONS

Display window

1Tr (track) indicator

2Source display / Track number / Folder number /

Time countdown indicator

3DISC indicator

4Sound mode indicators—CLASSIC, HIP HOP, JAZZ,

ROCK, POPS, USER

5Playback mode / item indicators—RND (random),

(disc), (folder), RPT (repeat)

6EQ (equalizer) indicator

7LOUD (loudness) indicator

8Disc information indicators—

TAG (Tag information), (track/file), (folder)

9Main display

pTuner reception indicators—ST (stereo),

MO (monaural)

EN02-09_KD-R400[J]_f.indd 5EN02-09_KD-R400[J]_f.indd 5 9/10/08 3:33:28 PM9/10/08 3:33:28 PM

ENGLISH

Installing the lithium coin battery (CR2025)

For USA-California Only:

This product contains a CR Coin Cell Lithium Battery

which contains Perchlorate Material—special

handling may apply.

See www.dtsc.ca.gov/hazardouswaste/perchlorate

Caution:

• Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

• Battery shall not be exposed to excessive heat such as

sunshine, fire, or the like.

If the effectiveness of the remote controller

decreases, replace the battery.

Before using the remote controller:

• Aim the remote controller directly at the remote

sensor on the unit.

• DO NOT expose the remote sensor to bright light

(direct sunlight or artificial lighting).

This unit is equipped with the steering wheel

remote control function.

• See the Installation/Connection Manual (separate

volume) for connection.

1• Turns the power on if pressed briefly or

attenuates the sound when the power is on.

• Turns the power off if pressed and held.

2• Changes the preset stations.

• Changes the folder of the MP3/WMA.

3Adjusts the volume level.

4Selects the sound mode.

5Selects the source.

6• Searches for stations if pressed briefly.

• Fast-forwards or reverses the track if pressed and

held.

• Changes the tracks if pressed briefly.

Warning (to prevent accidents and damage):

• Do not install any battery other than CR2025 or its

equivalent.

• Do not leave the remote controller in a place (such

as dashboards) exposed to direct sunlight for a long

time.

• Store the battery in a place where children cannot

reach.

• Do not recharge, short, disassemble, heat the battery,

or dispose of it in a fire.

• Do not leave the battery with other metallic

materials.

• Do not poke the battery with tweezers or similar

tools.

• Wrap the battery with tape and insulate when

throwing away or saving it.

Remote sensor

Using the remote controller (RM-RK50)

EN02-09_KD-R400[J]_f.indd 6EN02-09_KD-R400[J]_f.indd 6 10/24/08 9:11:25 AM10/24/08 9:11:25 AM

ENGLISH

7OPERATIONS

Preparation

Canceling the display demonstration and setting the clock

• See also page 14.

1Turn on the power.

[Turn] =[Press]

Cancel the display demonstrations

Select “DEMO,” then “DEMO OFF.”

Set the clock

Select “CLOCK” =“CLOCK SET.”

Adjust the hour, then press control dial once to proceed to adjust

the minute.

• To return to the previous menu, press BACK.

Changing the display information

When the power is turned off: The current clock time is displayed if “CLOCK DISP” is set to “CLOCK OFF,”

(see page 14).

When the power is turned on: The display information of the current source changes as follows:

FM/AM Frequency =Clock =Station name*1=(back to the beginning)

CD/USB

Audio CD/CD Text: Disc title/performer*2=Track title*2=Current track number with the

elapsed playing time =Current track number with the clock time =

(back to the beginning)

MP3/WMA: Album name/performer (folder name)*3=Track title (file name)*3=

Current track number with the elapsed playing time =Current track

number with the clock time =(back to the beginning)

*1If no title is assigned to a station, “NO NAME” appears. To assign a title to a station, see page 13.

*2If the current disc is an audio CD, “NO NAME” appears.

*3If an MP3/WMA file does not have Tag information or “TAG DISPLAY” is set to “TAG OFF” (see page 14),

folder name and file name appear.

Press and hold until

the main menu is

called up.

• Repeat this

procedure.

EN02-09_KD-R400[J]_f.indd 7EN02-09_KD-R400[J]_f.indd 7 9/10/08 3:33:29 PM9/10/08 3:33:29 PM

ENGLISH

Listening to the radio

1Select “FM” or “AM.”

2Search for a station to listen—Auto Search.

When a station is tuned in, searching stops. To stop searching, press the same

button again.

• You can also search for a station manually—Manual Search. Hold either one of

the buttons until “M” flashes on the display, then press it repeatedly.

• When receiving an FM stereo broadcast with sufficient signal strength, the ST

indicator lights up on the display.

Improving the FM reception

When an FM stereo broadcast is hard to receive,

activate monaural mode for better reception.

• See also page 15.

Reception improves, but stereo effect will be lost.

• The MO indicator lights up on the display.

To restore the stereo effect, repeat the same

procedure to select “MONO OFF.” The MO indicator

goes off.

Storing stations in memory

Automatic presetting (FM)—SSM (Strong-

station Sequential Memory)

You can preset up to 18 stations for FM.

1While listening to a station...

2Select the preset number range you want to

store.

Local FM stations with the strongest signals are

searched and stored automatically.

• To stop searching, press 4/¢.

To preset other 6 stations, repeat from step 1again.

[Turn] =[Press]

EN02-09_KD-R400[J]_f.indd 8EN02-09_KD-R400[J]_f.indd 8 9/10/08 3:33:30 PM9/10/08 3:33:30 PM

ENGLISH

9OPERATIONS

Continued on the next page

Selecting preset station

[Turn] =[Press]

Manual presetting (FM/AM)

You can preset up to 18 stations for FM and 6 stations

for AM.

Ex.: Storing FM station of 92.50 MHz into preset

number “04.”

2Select preset number “04.”

Disc operations

1Turn on the power.

2Insert a disc.

All tracks will be played repeatedly until you change

the source or eject the disc.

Stop playing and ejecting the disc

• “NO DISC” appears. Press SRC to listen to another

playback source.

Prohibiting disc ejection

To cancel the prohibition, repeat the same

procedure.

Selecting a track/folder

• For MP3/WMA discs, select the desired folder,

then the desired track by repeating the control dial

procedures.

• To return to the previous menu, press BACK.

[Turn] =[Press]

EN02-09_KD-R400[J]_f.indd 9EN02-09_KD-R400[J]_f.indd 9 9/10/08 3:33:31 PM9/10/08 3:33:31 PM

ENGLISH

10 OPERATIONS

Pressing (or holding) the following buttons allows you

to...

[Press]Pause/resume playback.

MP3/WMA: Select folder

[Press]Select track

[Hold] Reverse/fast-forward track

Selecting the playback modes

You can use only one of the following playback modes

at a time.

REPEAT

TRACK RPT : Repeats current track

FOLDER RPT : MP3/WMA: Repeats current folder

RANDOM

FOLDER RND : MP3/WMA: Randomly plays all

tracks of current folder, then

tracks of next folders

ALL RND : Randomly plays all tracks

[Turn] =[Press]

REPEAT ÔRANDOM

[Turn] =[Press]

• To cancel repeat play or random play, select

“RPT OFF” or “RND OFF.”

• To return to the previous menu, press BACK.

Listening to the USB

device

This unit can play MP3/WMA tracks stored in a USB

device.

All tracks will be played repeatedly until you change the

source or detach the USB device.

If a USB device has been attached...

Playback starts from where it has been stopped

previously.

• If a different USB device is currently attached,

playback starts from the beginning.

USB input jack

USB memory

EN10-15_KD-R400[J]_f.indd 10EN10-15_KD-R400[J]_f.indd 10 9/10/08 3:23:55 PM9/10/08 3:23:55 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere JVC Autoempfänger Handbücher

Beliebte Autoempfänger Handbücher anderer Marken

Motorola

Motorola VWA63 Bedienungsanleitung

Nextar

Nextar D3201 Bedienungsanleitung

Alpine

Alpine CDE-163BT Bedienungsanleitung

Pioneer

Pioneer DEH-P645R Bedienungsanleitung

Axxera

Axxera XDMA7600 Betriebsanleitung

XM OnyX Bedienungsanleitung

Sound Storm

Sound Storm STM93R Bedienungsanleitung

Soundstream

Soundstream VIR-5000 Bedienungsanleitung

Avson

Avson MKT Platform Bedienungsanleitung

Sony

Sony MEX-1HD - Audio Library System Bedienungsanleitung

Pioneer

Pioneer DVH-P500UB Bedienungsanleitung

Blaupunkt

Blaupunkt SANTIAGO CR 87 Bedienungsanleitung

Sony

Sony CDX-4160 - Cd Receiver Bedienungsanleitung

XFIRE AUDIO

XFIRE AUDIO BMW42S Bedienungsanleitung

VDO

VDO CD 2253 Bedienungsanleitung

Volvo

Volvo 13 84 580 Bedienungsanleitung

ZENEC

ZENEC ZE-160DVD Bedienungsanleitung

Medion

Medion Car Audio Bedienungsanleitung