Kaba Simplex 1000 Series Installationsanleitung

Access Control - 1000 Series PBL FAQ

1000 Series FAQ

Resetting the Code / Combination

From a Lost Code

Important: There is no procedure for finding an unknown

combination from the front of the lock. A lost combination must be

cleared by removing the combination chamber from the lock

housing, then a new combination can be set.

1. Remove the back plate from the front lock housing by removing

the six back plate screws.

2. Lift the chamber linkage (A) off of the control shaft (B) by

prying up with a small flat blade screwdriver (see figure 1).

3. Remove the shaft bushing (C).

4. Remove the combination chamber (D) by removing the two

Phillips head screws (E) at each end of the combination chamber.

5. Remove the chamber cover (A) marked Ilco Unican (see figure

2) by gently tapping the lip of the chamber cover at the control

shaft end of the chamber (A) (see figure 3) with a screwdriver to

detach it from the staked joints (B).

6. Lay the chamber on its side as shown in figure 4.

7. With tweezers, or other tool, slide the "e" ring (B) off the

unlocking slide stud (A) (see figure 4), then gently lift the end of

the unlocking slide (C) over the unlocking slide stud (A).

Note: The unlocking slide (C) is under spring tension and will be

easier to lift if pushed to the left to ease tension. Swing the

unlocking slide (C) sufficiently to clear the gears (D), no further

than shown in figure 5.

8. Depress the lockout slide (E). The gears (D) are now free to

rotate (see figure 6).

9. Turn each gear (D) so that the gear pockets (F) are aligned as

in figure 6.

For a larger view

of these images,

click here

http://www.kaba-ilco.com/access_control/support/pbl_faq/resetting_code_combination/1000_series.asp (1 of 2) [5/21/2004 11:11:14 AM]

Access Control - 1000 Series PBL FAQ

10. Return the unlocking slide (C) over the unlocking slide stud

(A) while making certain the five toes (G) are engaged in the five

gear pockets (F). It may be necessary to adjust each gear slightly

to make proper alignment between toes and gear pockets (see

figures 6 & 7). Resecure the "e" ring (B) on the unlocking slide

stud (A). Your chamber will now resemble figure 7. and is ready

for reassembly into the lock housing.

REASSEMBLY

1. Resecure the chamber cover (A). Make sure the staked joints

(B) on both end plates fit through both slots on the back cover

(see figure 2).

2. Resecure the shaft bushing (C) with flat side facing up (see

figure 1).

3. Secure the combination chamber (D) with the two Phillips head

screws (E) you removed earlier (see figure 1).

4. Resecure the chamber linkage (A) onto the control shaft (B)

(see figure 1).

5. Resecure the back plate and secure it with the six back plate

screws.

SETTING THE COMBINATION

Do not attempt to set a combination until the complete unit has

been reassembled. Perform the following steps in the order shown.

1. Turn the outside knob once clockwise to the stop position and

then release.

2. Enter the new combination.

3. Turn the outside knob clockwise to the stop position, make sure

the latch is fully retracted, then release the knob.

4. Repeat steps 2 & 3 before closing your door to confirm code

setting.

PRINT THIS SECTION

http://www.kaba-ilco.com/access_control/support/pbl_faq/resetting_code_combination/1000_series.asp (2 of 2) [5/21/2004 11:11:14 AM]

Andere Handbücher für Simplex 1000 Series

Inhaltsverzeichnis

Andere Kaba Sperren Handbücher

Kaba

Kaba 52 Bedienungsanleitung

Kaba

Kaba SIMPLEX EE1000 Series Bedienungsanleitung

Kaba

Kaba KEYLESS ENTRY LOCK Bedienungsanleitung

Kaba

Kaba LA GARD 1947 Bedienungsanleitung

Kaba

Kaba E-730 Series Bedienungsanleitung

Kaba

Kaba X-09 Bedienungsanleitung

Kaba

Kaba SIMPLEX 7102 Series Bedienungsanleitung

Kaba

Kaba Generation E-760 AUTO DEADBOLT ASM Office Bedienungsanleitung

Kaba

Kaba Simplex 3000 Series Bedienungsanleitung

Kaba

Kaba Simplex 8100 Series Bedienungsanleitung

Kaba

Kaba E-Plex 5200 Bedienungsanleitung

Kaba

Kaba COMBOGARDPRO Bedienungsanleitung

Kaba

Kaba PowerPlex 2000 Series Bedienungsanleitung

Kaba

Kaba Quantum Series Bedienungsanleitung

Kaba

Kaba simplex 7106 series Bedienungsanleitung

Kaba

Kaba C-lever compact Bedienungsanleitung

Kaba

Kaba 7006 Series Bedienungsanleitung

Kaba

Kaba La Gard MECHANICAL Bedienungsanleitung

Kaba

Kaba 7004 Series Bedienungsanleitung

Kaba

Kaba E-Plex 5 Series Bedienungsanleitung

Kaba

Kaba E-PLEX 2000 Bedienungsanleitung

Kaba

Kaba E-Plex 5000 Bedienungsanleitung

Kaba

Kaba E-Plex 50 Series Bedienungsanleitung

Kaba

Kaba SILCA SW- VAG GROUP-L0 Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung