Kangaroo Wallaby II Bedienungsanleitung
SEW IN COMFORT. SEW LONGER.™
ASSEMBLY INSTRUCTIONS
Wallaby II
ITEM NO.: K8405 Teak
K8411 White Ash
2
Wallaby II Assembly Instructions
Read the instructions carefully before starting. Please open and inspect the contents of boxes to
see that all parts are included. You will need a Phillips head and a flat head screwdriver. A power
screwdriver or cordless drill is preferable. Ensure that the Phillips head fits neatly and fully engages
the screw to avoid damage to the screws. Make sure that you tighten all screws securely and tap
wooden dowels all the way in.
Use and Care
Your cabinet normally requires a minimum amount of maintenance; however, the following points are
worth noting:
Cleaning – To remove marks and enhance the surface, wipe with general purpose cleaner.
Caution – Do not use ammonia-based cleaning agents. Do not use harsh chemicals or abrasive
cleansers. The surface can be wiped with a damp cloth but should be dried quickly.
Electrical and Hydraulic Lifts – Require annual lubrication.
180°
Screw cam bolts flush as
illustrated.
Press cam Into hole until flush with
surface. The arrow direction must
be in the direction of the hole!
Insert bolt through pre-drilled
hole in edge of panel.
Understanding How the Cam Fastener Works
Turn clockwise to lock cam with bolt.
3
Wallaby II Assembly Instructions
Parts List
ITEM DESCRIPTION QT Y. PACK.
ATop Panel 1 1 of 4
BRight Leaf 1 1 of 4
CLeft Leaf 1 1 of 4
A5 Platform Cover 1 1 of 4
GBottom Panel 1 1 of 4
DBack Panel 1 2 of 4
ZRight Side Panel 1 2 of 4
A1 Quilt Extension Panel 1 2 of 4
V1 Left Door Panel 1 2 of 4
V2a Right Main Door Panel 1 3 of 4
XLeft Side Panel 1 3 of 4
YPartition 1 3 of 4
FFixed Shelf 1 3 of 4
ITEM DESCRIPTION QT Y. PACK.
V2b Right Door Edge Panel 1 3 of 4
LDrawer Front 1 3 of 4
L1 Drawer Side Left 1 3 of 4
L2 Drawer Side Right 1 3 of 4
L3 Drawer Back 1 3 of 4
L4 Drawer Bottom 1 3 of 4
OInsert Holder 1 3 of 4
01 Gate Leg 1 3 of 4
K1 Door Bin Front Panel 1 3 of 4
K2 Door Bin Bottom Panel 1 3 of 4
K3 Door Bin Sides 2 3 of 4
K4 Fixed Shelf On Door 3 3 of 4
A4 Platform 1 3 of 4
Lift & Rails 1 4 of 4
K3
K3
K1
K2
K4
K4
K4
V2a
V2b
Z
A
C
B
A5
A1
O1
D
A4
O
G
X
V1
F
Y
L3
L1
L4
L
L2
4
Wallaby II Assembly Instructions
Parts List
6x35 Cam Bolt x35
3.5x14 Screw x52 3x14 Screw x28 3x20 Screw x4
Wrench x1 Handle x2 Door Plate x2 14mm Spanner x1
Stay Arm x1
Cam
6x25 Cam Bolt x25
5⁄8“ Cam Cover x60 6x50 Dowel Pin x33
Alignment Pin x1
Flap Hinge x3
Caster x3 Locking Plate Caster x5
Butt Hinge x2 Flush Hinge x6
Lock x1 Magnet x1
Lock plate x1 Catch plate x1Key x2
8x16 Fix Bolt x20 4x20 Fix Bolt x4
Pre-installed parts
ITEM DESCRIPTION QT Y.
c1 6x35 Cam Bolt 35
c3 6x25 Cam Bolt 25
d1 8x30 Dowel Pin 36
d2 6x50 Dowel Pin 33
c2 5⁄8“ Cam Cover 60
t2 Locking Plate Caster 5
aWrench 1
s2 3x14 Screw 28
SStay Arm 1
r3 14mm Spanner 1
d3 Door Plate 2
s5 Alignment Pin 1
ITEM DESCRIPTION QT Y.
s3 3.5x35 Screw 4
hHandle 2
h3 Flap Hinge 3
h2 Flush Hinge 6
b2 4x20 Fix Bolt 4
b1 8x16 Fix Bolt 20
s1 3.5x14 Screw 52
mMagnet, Catch Plate 1
LLock, Lock Plate, Keyx2 1
t1 Caster 3
h1 Butt hinge 2
s4 3x20 Screw 4
d2
s5
b2
s2
s4
h
d3
r3
h1
h2
L
m
t1
t2
Drawer RunnersCaster Bracket
8x30 Dowel Pin x12
d1
3.5x35 Screw x4
c1
c3
h3
b1
s1
a
s
c2
c5
s3
Wallaby II 5Assembly Instructions
3.5x14 Screw x23
Stay Arm x1
8x30 Dowel Pin x12
Magnet x1
Lock Plate x1
Catch Plate x1
d1
r3
L
m
t1
Step 1. Preparation Panels A, A1, Z, X, F and O1
1. Insert cams bolts c1 into panels A, Xand Zas illustrated below.
2. Insert dowel pins d1 to panels X, Zand Fas illustrated below..
3. Fix Stay Arm susing Screws s1 to panel Aas illustrated below.
4. Fix Lock Plate using Screws s1 to panel Aas illustrated below. Orient the flat face of lock plate Ltowards front edge of
panel A.
5. Fix Magnet musing Screw s1 to panels A1 as illustrated below.
6. Fix Flap Hinge h3 using Screw s1 to panels A1 as illustrated below.
7. Fix Butt hinges h1 using Screws s1 as shown on Panel O1. Insert the Alignment pin s5.
8. Insert the caster t1 into the pre-installed caster bracket on panel O1 and tighten with spanner r3.
9. Fix Catch plate mto panel O1 using screws s1.
h3
Flap Hinge x3
14mm Spanner x1
Caster x1
6x35 Cam Bolt x15
Butt Hinge x2
Alignment Pin x1
c1
c1
c1
h3
s1
s1
s1
s1
s1
s
s
Z
A
O1
A1
X
F
L
m
t1
r3
s5
s1
s1
h1
c1
m
h1
s5
6x25 Cam Bolt x25
c3
4x20 Fix Bolt x4
b2
Wallaby II 6Assembly Instructions
3.5x14 Screw x4
Step 2. Preparation Panels Y, D, 0, V1, V2a, V2b, K1, K3, K4, L, L3 and L2
1. Insert cam bolts c1 into panels Yand V2a and Las illustrated below.
2. Insert cam bolts c3 into panels V2a, K1 and K3 as illustrated below.
3. Insert dowel pins d1 into edges of panels Y, D, V2b, L1 and L2 using glue as illustrated below.
4. Insert dowel pins d2 into top of panels K4 using glue to secure.
5. Fix Lock mechanism Linto corner of V2a using s4 screws. Add trim ring to exterior end of lock.
6. Fix Door plate d3 to panel V1 using screws s1.
7. Attach Flush Hinges h2 to panel V1 using s2 screws as shown.
8. Attach the screw-in caster to V1 and V2a panel caster bracket and tighten with spanner t1.
9. Attach door handles hto exterior of V1 and V2a using fix bolts b2 as shown.
14mm Spanner x1
Caster x2
x3
6x35 Cam Bolt x6
6x50 Dowel Pin x33
3x20 Screw x4
Lock x1
Key x2
Door Plate x2
Flush Hinge x3
3x14 Screw x6
Handle x2
8x30 Dowel Pin x12
c1
c1
c1
c1
c1
b2
h
h2
s1
s2
D
Y
L
L
s4
t1
r3
d3
c3
c3
c3
K3
K1
K4
V2a
V2b
O
V1
L
d3
h2
d1
r3
t1
c1
s1
d2
s4
L
s2
h
x2
L2
L1
Wallaby II 7Assembly Instructions
3.5x14 Screw x3
Step 3. Fix Lifter Rail (right) to Zpanel with s1 screws following predrilled holes as shown on the illustration below.
Step 4. Fix Lifter Rail (Left) to Ypanel with s1 screws following predrilled holes as shown on the illustration below.
Lifter Rail (Right) x1
Lifter Rail (Left) x1
3.5x14 Screw x3
Rail faces front of panel.
Detail beside shows the holes
on back as it attaches to panel.
s1
s1
s1
s1
Y
Z
Wallaby II 8Assembly Instructions
Step 5. Panels D, X, Z assembly.
Insert cam bolts c1 on panels Xand Zinto cams on panel Dand tighten in a clockwise direction as illustrated below. Apply
cam covers c2 over tightened cams.
Panel D has the cams facing
outside to the back of the
cabinet and will be covered
with stickers provided.
Step 6. Panel F and Y assembly.
Insert cam bolts c1 on panels Xand Yinto cams on panel Fand tighten in a clockwise direction as illustrated below. Apply
cam covers c2 over tightened cams.
Important Note:
We recommend doing this step
with panels upside down so
panels are in correct position for
Step 6 on page 8 and Step 8 on
page 9.
180°
180°
5⁄8“ Cam Cover x4
5⁄8“ Cam Cover x4
Z
Z
Y
F
D
D
X
X
c2
c2
c5
c5
180°
Wallaby II 9Assembly Instructions
Step 7. Panel G assembly.
1. Fix casters t2 to panel Gwith bolts b1 as illustrated below.
2. Flip panel Gover to top side. Install cam bolts c1 as illustrated below.
3. Attach insert holder Oby inserting cam bolts c1 on panel Ginto Oand tightening cams clockwise.
Step 8. Panel G assembly.
1. Remove the drawer runners from panels Xand Y.
2. Insert cam bolts c1 on panel G into cams on panels X, D, Yand Zand tighten in a clockwise direction as illustrated
below. Apply cam covers c2 over tightened cams.
3. Attach the drawer runners on panels Xand Y.
Locking Plate
Caster x5
8x16 Fix Bolt x20
6x35 Cam Bolt x11
Wrench x1
180°
5⁄8“ Cam Cover x9
1. 2.
3.
G
X
X
Y
X
Y
Y
Z
D
G
t2
t2
b1
b1
c1
a
O
G
c5
c2
c5
Wallaby II 10 Assembly Instructions
Step 10. Lifter Panel assembly.
Fix Lifter to A4 panel with s1 screws following predrilled holes as shown on the illustration below.
Note: Remove cable ties (do not remove wooden block).
Step 9. Flip cabinet over (right side up).
3.5x14 Screw x4
s1
Lifter x1
A4
s1
Andere Handbücher für Wallaby II
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Beliebte Nähmaschinenzubehör Handbücher anderer Marken
JUKI
JUKI IP-200 Benutzerhandbuch
Sullivans
Sullivans Sew & Go Bedienungsanleitung
Sailrite
Sailrite ULTRAFEED 120931 Bedienungsanleitung
Bernina
Bernina Spanish Hemstitch Equipment 47 Bedienungsanleitung
Brother
Brother ScanNCut DX Stamp Starter Kit Bedienungsanleitung
ELNA
ELNA 495-526-20 Bedienungsanleitung