Kendal Lighting AC11152P-ORB/WN Bedienungsanleitung

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Model: AC11152P-ORB/WN

2. PACKAGE CONTENTS

Unpack your fan and check the contents. You

should have the following items;

a. Blade set (5)

b. Hanger bracket

c. Canopy

d. Downrod

e. Coupling cover

f. Fan motor assembly

g. Set of blades bracket (5)

h. Switch housing

i. Package hardware

1) Mounting hardware :

wood screws (2), screws (2), lock washers (4),

washers (2), wire nuts (3), rubber gasket (2)

2) Blade attachment hardware:

screws (16), fiber washers (16)

3) Close-to-ceiling attachment hardware:

screws with lock washers (3)

4) Pull chain and fob

5) Balance Kit

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

1. TOOLS AND MATERIALS

REQUIRED

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local electrical

codes. Electrical installation should be

performed by a qualified licensed electrician.

3. CAUTION: Read all instructions and safety

information before installing your new fan.

Review accompanying assembly diagrams.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and lock

washers) provided with the outlet box for

mounting to the outlet box. Most outlet boxes

commonly used for the support of lighting

fixtures are not acceptable for fan support and

may need to be replaced, consult a qualified

electrician if in doubt.

5. The outlet box and support structure must be

securely mounted and capable of reliably

supporting a minimum of 50 pounds. Use only

CUL Listed outlet boxes marked "FOR FAN

SUPPORT".

6. The fan must be mounted with a minimum of 7

feet clearance from the trailing edge of the

blades to the floor.

7. Do not operate the reverse switch while the fan

blades are in motion. The fan must be turned

off and the blades stopped before reversing

the blades direction.

8. Avoid placing objects in the path of the blades.

9. To avoid personal injury or damage to the fan

and other items, be cautious when working

around or cleaning the fan.

10. Do not use water or detergents when cleaning

the fan or fan blades. A dry dust cloth or lightly

dampened cloth will be suitable for most

cleaning.

11. After marking electrical connections, spliced

conductors should be turned upward and

pushed carefully up into outlet box. The wires

should be spread apart with the grounded

conductor and the equipment-grounding

conductor on one side of the outlet box.

12. Electrical diagrams are reference only. Light kit

that are not packed with the fan must be CUL

Listed and marked suitable for use with the

model fan you are installing. Switches must be

CUL General Use Switches. Refer to the

Instructions packaged with the light kits and

switches for proper assembly.

3. SAFETY RULES

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT

FAN TO OUTLET BOX MARKED

"ACCEPTABLE FOR FAN SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS IN

THE PATH OF THE BLADES.

4. MOUNTING OPTIONS

If there isn't an existing CUL listed mounting box,

then read the following instructions. Disconnect the

power by removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and building

materials. The outlet box and its support must be

able to fully support the moving weight of the fan

(at least 50 lbs). Do not use plastic outlet boxes.

Figures 1,2 and 3 are examples of different ways to

mount the outlet box.

Note: You may need a longer downrod to maintain

proper blade clearance when installing on a steep,

sloped ceiling. (Fig. 3)

To hang your fan where there is an existing fixture

but no ceiling joist, you may need an installation

hanger bar as shown in Figure 4.

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Figure 1

Figure 3

Figure 4

Outlet box

Figure 2

Figure 7

Registration slot

5. HANGING THE FAN

Mounting screws

(supplied with

electrical box)

Hook

Ceiling

mounting

plate

CUL Listed

electrial

box

Figure 5

Figure 6

120V Wires

Washers

Downrod

Canopy

Set screws

Locking

Hanger pin

Coupling cover

REMEMBER to turn off the power. Follow the steps

below to hang your fan properly:

NOTE: This ceiling fan is supplied with two types of

hanging assemblies; the standard ceiling

installation using the downrod with ball and socket

mounting and the "close-to-ceiling" installation.

The "close-to-ceiling" installation is recommended

in rooms with less than 8-feet ceilings or in areas

where additional space is desired from the floor to

the fan blades.

STANDARD CEILING INSTALLATION

Step 1. Pass the 120-volt supply wires through the

center hole in the ceiling hanger bracket as shown

in Fig. 5.

Step 2. Secure the hanger bracket to the ceiling

outlet box with the screws and washers provided

with your outlet box.

Step 3. Remove the hanger pin, lock pin and set

screws from the top of the motor assembly.

Step 4. Route wires exiting from the top of the fan

motor through the couping cover, canopy and then

through the ball / downrod. (Fig. 6)

Step 5. Align the holes at the bottom of the

downrod with the holes in the collar on top of the

motor housing. Carefully insert the hanger pin

through the holes in the collar and downrod. Be

careful not to jam the pin against the wiring inside

the downrod. Insert the locking pin through the hole

near the end of the hanger pin until it snaps into its

locked position, as noted in the circle inset of Fig. 6.

Step 6. Tighten two set screws on top of the fan

motor firmly. (Fig. 6)

Step 7. Place the downrod ball into the hanger

bracket socket. (Fig. 7)

Figure 8

Figure 9

Figure 10

CLOSE-TO-CEILING INSTALLATION

1. Remove the decorative canopy bottom cover

from the canopy by depressing the three studs

(Fig. 8)

2. Pass the 120-volt supply wires through the

center hole in the ceiling hanger bracket as

shown in Fig. 5.

3. Secure the hanger bracket to the ceiling outlet

box with the screws and washers provided with

your outlet box.

4. Place the ceiling canopy over the collar at the

top of the motor. Align the mounting holes with

the holes in the motor and fasten using the

screws and lock washers provided (Fig. 9).

5. Tighten the mounting screws securely. (Fig. 9)

WARNING: Failure to completely tighten the three

screws in step 5 could result in fan loosening and

possibly falling.

6. Hang the fan on the hook of the hanger bracket.

Be certain that the canopy is fully locked into

hook as shown in Fig. 10. This will allow you to

make the electrical connections.

Canopy bottom cover

Hook

Screw and lock washer

Canopy

Collar

6. INSTALLATION OF

SAFETY SUPPORT

An additional safety support is provided to prevent

the fan from falling. Secure the safety cable to the

ceiling joist with screw and washer, as illustrated in

Figure 11.

7. MAKE THE ELECTRIC

CONNECTIONS

Remember to disconnect the power.

Follow the steps below to connect the fan to your

household wiring. Use the wire connecting nuts

supplied with your fan. Secure the connectors with

electrical tape. Make sure there are no loose

strands or connections.

Step 1 Connect the fan supply (black) wire and

light supply (blue) wire to the black household

supply wire as shown in Figure 12.

Step 2. Connect the neutral fan (white) wire to the

white neutral household wire.

Step 3 Connect the fan ground wire (green) to the

household ground wire.

Step 4 After connecting the wires, spread them

apart so that the green and white wires are on one

side of the outlet box and the black and the blue

wires are on the other side.

Step 5 Turn the connecting nuts upward and push

the wiring into the outlet box.

Figures 13 and 14 illustrate the wiring connections

for optional wall control (The wire color out of wall

control may vary, see wall control's installation

manual for correct wire connections.)

Hanger bracket Safety cable

Figure 11

Figure 12

Figure 13

BLK

WIRING

BOX

GROUND TO

MOUNTING

BRACKET

OR DOWNROD

POWER LINES 120V

BLUE

BLK

FAN

LIGHT

BLK

BLUE WH

LIGHT

SWITCH

GREEN GROUND

BLUE

BLK

GRN

WIRING

BOX

GROUND TO

MOUNTING

BRACKET

OR DOWNROD

BLUE

BLK WH

FAN

LIGHT

POWER LINES 120V

BLK

GREEN GROUND

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, OR OTHER PERSONAL

INJURY. MOUNT FAN ONLY ON AN OUTLET

BOX OR SUPPORTING SYSTEM MARKED

ACCEPTABLE FOR FAN SUPPORT.

8. FINISHING THE

INSTALLATION

STANDARD CEILING INSTALLATION

Slide canopy up to the ceiling as shown in Figure

15. Make sure you place the wires safely into the

outlet box. Secure the canopy to the hanger

bracket with the four screws with your fan.

CLOSE-TO-CEILING INSTALLATION

Remove the fan from the hook on the hanger

bracket. Secure the canopy to the hanger bracket

as shown in Figure 16 with four screws included

with your fan.

Figure 14

Figure 15

Figure 16

GROUND TO

MOUNTING

BRACKET

OR DOWNROD

POWER LINES 120V

GREEN

GROUND

WIRING

BOX

BLK

FAN

LIGHT

BLUE

BLK

LIGHT

FAN

Outlet box

Hanger

bracket

Canopy

Screws

Outlet box

Hanger

bracket

Canopy

Screws

Figure 17

Figure 18

9. ATTACHING THE FAN

BLADES

CAUTION: Remove 5 rubber packing mounts and

discard before installation.

Step 1 Attach the blade to the blade bracket using

the screws and fiber washers as shown in Figure

17. Start screw into bracket. Repeat for the two

remaining screws.

Step 2 Tighten each screw. Make sure the blade is

straight.

Step 3 Fasten blade assembly to motor using the

screws supplied. (Fig. 17)

10. INSTALLING THE

SWITCH HOUSING

NOTE: Before starting installation, disconnect

the power by turning off the circuit breaker or

removing the fuse at fuse box. Turning power

off using the fan switch is not sufficient to

prevent electric shock.

1. Remove the screws from the mounting plate

under the fan motor.

2. While holding the switch housing under

your fan, snap together the wire connection

plug. (Fig. 18)

3. Raise the switch housing to the mounting

plate until the holes in switch housing and

mounting plate line up. Reinsert screws to

secure in place. (Fig. 18)

Blade

Blades bracket

Screws

Fiber

washers

Screws

Switch

housing

Connection plug

Figure 19

Figure 20

11. OPERATING

INSTRUCTIONS

NOTE: Wait for fan to stop before changing the

setting of the slide switch.

Turn on the power and check the operation of your

fan.

1. 3-speed pull chain- it controls the fan speed as

follows: 1 pull- High, 2 pulls- Medium, 3 pulls-

Low, and 4 pulls- Off.

Speed settings for warm or cool weather depend

on factors such as the room size, ceiling height,

number of fans, and so on.

2. Light pull chain it controls the light in "ON" or

"OFF".

The slide switch controls directions: forward (switch

left ) or reverse (switch right ).

Warm weather - (Forward) A downward air flow

creates a cooling effect as shown in Figure 19.

This allows you to set your air conditioner on a

higher setting without affecting your comfort.

Cool weather - (Reverse) An upward airflow moves

warm air off the ceiling area as shown in Figure 20.

This allows you to set your heating unit on a lower

setting without affecting your comfort.

Inhaltsverzeichnis

Andere Kendal Lighting Lüfter Handbücher

Kendal Lighting

Kendal Lighting AC-22160 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-21750 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-24144 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-24060 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-21052 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-20070 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-21560 Bedienungsanleitung

Kendal Lighting

Kendal Lighting Lopro KENAC21352SN Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-22452 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-20152 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-22656 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-16652 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-30152 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-21454 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-22552 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-21852 Bedienungsanleitung

Kendal Lighting

Kendal Lighting Virtua Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-30552 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-20452 Bedienungsanleitung

Kendal Lighting

Kendal Lighting Triax AC-22352 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-30052 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-30952 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-23960 Bedienungsanleitung

Kendal Lighting

Kendal Lighting AC-23856 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung