Kenmore 625.384450 Bedienungsanleitung

OWNER'S MANUAL

Deluxe Multi-Purpose

Water System

MODEL NO. 625.384450

Caution:

Read and follow all safety rules and operating

instructions before first use of this product.

Questions ?

Visit www.KenmoreWater.com

or call toll free 1-800-426-9345 (M - F, 7 AM - 6 PM CST)

Repair or Parts ?Call toll free 1-800-469-4663

See back cover for other Sears service numbers.

SAVE THIS MANUAL

•Warranty

•installation

• How It Works

• Care Of

• Specifications

• Repair Parts ®

Printed on recycled paper

Sears Brands Management Corporation, Hoffman

PRINTED IN U.S.A. www.KenmoreWater.com

Estates, IL 60179 U.S.A.

Part No. 7293890 (Rev. D 2/8/11)

ONE YEAR FULL WARRANTY ON THE

DELUXE MULTI-PURPOSE WATER FILTER

When installed, operated and maintained according to all instructions supplied with the product, if this

Deluxe Multi-Purpose Water Filter fails due to a defect in material or workmanship within one year from the

date of purchase, Sears will replace this Deluxe Multi-Purpose Water Filter free of charge.

This warranty does not include filter cartridges, which are expendable items.

This warranty is available by simply returning the Deluxe Multi-Purpose Water Filter to the nearest Sears

store throughout the United States.

This warranty applies only while this product is in use in the United States or Canada.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Sears Brands Management Corporation, Hoffman Estates, IL 60179

14-1/4"

5-1/4" 5-1/4"

Questions? Call The I<enmore Water Line 1-800-426-9345 or visit I<enmoreWater.com

Unpack and Check Shipment ...................................................................... 4

Plan Your Installation ............................................................................. 5

Typical Installations .............................................................................. 6

Installation ................................................................................... 7-9

Water Treatment Filter Cartridges .................................................................. 10

Filter Cartridge Life ............................................................................. 10

Filter Cartridge Replacement ...................................................................... 11

Adjustable Filter Wrench ......................................................................... 12

Specifications .................................................................................. 13

Exploded View & Parts List ....................................................................... 14

•Read this entire manual carefully before installing and

using your Deluxe Multi-Purpose Water Filter. Follow

all steps exactly to correctly install.

• Check with your local public works department for

plumbing and sanitation codes. You must follow their

guides as you install the system. Follow your local

codes if they differ with guides in this manual. In

Massachusetts, plumbing codes of Massachusetts shall

be adhered to. Consult with a licensed plumber.

• Maximum operating pressure: 100 psi.

• Maximum temperature: IO0°F.

• For cold water use only. Do not install on a hot water

line.

• Not to be used on water that is microbiologically

unsafe or of unknown quality without adequate disin-

fection before or after the system.

• Keep solvents and sprays away from the clear sump

housing material. Surface cracking and failure can

result.

• Do not install where pressure surges exceed 100 psi.

Install a pressure regulator before the filter if needed.

• Do not install outdoors in direct sunlight.

• Do not install where freezing may occur.

• Misapplication of clear housing voids your warranty.

• It is important to properly seat the o-ring in the groove

of the sump housing, or a water leak could occur.

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

INSPECT SHIPMENT

Your Deluxe Multi-Purpose Water Filter is shipped com-

plete in one carton. Remove all items from your shipping

carton.

Check all items against the packing list below. Note any

items lost or damaged in shipment. Note any damage to

the shipping carton. Refer to the exploded view and

parts list in the back of the manual for the part names

and numbers of missing or damaged items. If problems

exist, refer to the website or the toll free number listed

throughout this manual.

NOTE: Codes in the state of Massachusetts require instal-

lation by a licensed plumber.

If you live in the state of Massachusetts, review plumbing

code 248-CMR of the Commonwealth of Massachusetts

before proceeding with the installation.

Deluxe Multi-Purpose Water Filter,

including 25 micron Sediment Cartridge Adjustable Filter Wrench

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

INSTALLATION LOCATION

To filter sediments from all house water, locate the Deluxe

Multi-Purpose Water Filter on the main water supply pipe

(See Figure 1). Please ask your Sears associate about

products that will remove taste and odor from your water

throughout your home. You can also filter water to one

faucet. For example, install the filter under the kitchen

sink to filter the cold drinking water (See Figure 2).

PLANNING YOUR INSTALLATION

When planning the installation, first read the "Water

Treatment Filter Cartridges" section on Page 10 to deter-

mine where to locate the water filter housing. Then, use

the drawings on Page 6as a guide. There are many vari-

ables to consider as you plan. Some of these are:

• The Deluxe Multi-Purpose Water Filter inlet and outlet

internal threads are 3/4" NPT

• Existing plumbing type (copper, threaded, etc.) and

nominal size (1/2", 3/4", etc.)

• Tools you have, and your plumbing skills

• Space available for installing the Deluxe Multi-Purpose

Water Filter

Make a simple sketch of your proposed installation, and a

list of plumbing materials you will need. Obtain every-

thing you need before starting the installation.

Filtering All House Water

To Outside Faucets

Cold Water

to House

Faucets &

Water Heater Multi-Purpose

Water Filter

City Water Supply

Pressure

Tank

__ ell Water Supply

Well _

Pump t

Figure 1

Filtering Water to One Faucet

Kitchen Sink

Multi-Purpose

HOT COLD lil Ill Water Filter

LUJ Figure 2

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

A. INSTALLATION ON COPPER PLUMBING USING COMPRESSION FITTINGS

MATERIALS & TOOLS NEEDED

• 2 compression adaptors, 3/4" NPT x com-

pression end to fit existing copper pipe

• Teflon tape Optional

• Tubing cutter Shutoff

• Sandpaper or emery cloth Valve

• 2 wrenches, either open end or adjustable /

jaw, sized to fit compression adaptors f

Apply 4 wraps of Optional

Teflon Tape Shutoff Valve

INLET

WATER 3/4" NPT

NOTE: Be sure to allow a minimum space of 2" under the

filter for removing the sump (to change the cartridge).

Nut

Brass

Ferrule

Compression

Adaptor

WATER

OUT

Figure 3

B. SOLDERED COPPER INSTALLATION

WATER _ IN _ OUT _ WATER

IN "_ _ "_ OUT

Shutoff 3/4'Copper I H II_ ×Sweat(Apply

Valve (2) Pipe: as, I II I I 4 wraps of

requlrea _,___ Teflon Tape)

See Note in Figure 3 $ Figure 4

C. THREADED INSTALLATION

WATER _ IN.OUT c_ WATER

,N _@___i_[]i_ OUT

Optional 3/4" 3/4" Hex Union

• Jl II _ Nipple Fitting

Shutoff Nipple

Valve (2) (2) _ (2) (2)

See Note in Figure 3 , Figure 5

D. UNDERSINK INSTALLATION

(Filtering Water to One Faucet)

t ii ii

hut ve

NOTE: To change the filter

cartridge, refer to

the instructions on

Pages 11& 12 in this

manual• NOTE: Be sure to allow a

minimum space of

2" under the filter

for removing the

sump (to change

the cartridge).

Figure 6

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

A. WATER FILTER ON HOUSE MAIN WATER PIPE, TO FILTER ALL HOUSEHOLD WATER

USING COMPRESSION FITTINGS (See Figure 3 on Page 6)

INSTALLATION STEPS

1. Apply 4wraps of Teflon tape to the threads of both

compression fittings.

2. Carefully turn the compression fittings into the water

filter head inlet and outlet and tighten. Do not cross-

thread and damage the threads. Do not overtighten

and crack the head.

3. Remove the nut and brass ferrule from both compres-

sion fittings and set aside. Using a tape measure or

ruler, measure the distance "D" as shown in Figure 7).

Mark this dimension at right so you do not forget.

4. IMPORTANT: Turn off the water supply to the main

pipe. Open a high and low faucet in the water system

to drain the pipe.

5. On the main water pipe, where you will install the filter,

mark the dimension "D". You will remove this section

of pipe. Before you begin to cut, double-check your

measurement.

6. Use a tubing cutter to remove the section of pipe.

Remove all burrs and rough edges with the sandpaper

or emery cloth.

7. Place a nut and brass ferrule from compression fittings

onto both pipe ends (See Figure 8).

8. With the IN side of the water filter toward incoming

water, spread the pipes apart and fit both pipe ends

into the compression fittings. Move a ferrule and nut

up to the fitting (See Figure 9). Then, turn on and

tighten the nut. Hold the fitting with one wrench while

tightening the nut with the other. Repeat on the other

side.

9. Before turning on the water supply, remove the sump

from the filter head and install the filter cartridge (See

Page 11).

7D "1

a--- II

Measure to shoulder

inside of fittings.

Copper pipe butts

against this shoulder.

Figure 7

Nut Brass Brass Nut

Ferrule Ferrule

Figure 8

Nut

tJ V c

WATER FLOW

Brass

Ferrule

Nut

Figure 9

GROUNDING INFORMATION:

The house cold water pipe is often used to ground electri-

cal outlets in the home. Grounding protects you from

electrical shock. Installing the water filter housing may

have broken this ground. To restore, buy and install a #4

copper wire across the filter, tightly clamped at both

ends, as shown in Figure 10.

Ground

Wire "_

Clamp

(2) Figure 10

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

B. WATERFILTERON HOUSEMAIN WATERPIPE,TO FILTERALL HOUSEHOLDWATER

USINGSOLDEREDCOPPERFITTINGS(SeeFigure4on Page 6)

MATERIALS AND TOOLS NEEDED:

You will need 2 sweat adaptors, 3/4" NPT x sweat (sweat

end to fit your main water pipe), lead-free solder and

flux, soldering torch, Teflon tape, sandpaper or emery

cloth, open end (to fit sweat adaptor) or adjustable jaw

wrench.

INSTALLATION STEPS

CAUTION: Heat created when soldering can damage the

water filter's plastic parts. Be sure to use the following

procedure to protect the water filter.

1. IMPORTANT: Turn off the water supply to the main

pipe. Open a high and low faucet in the water system

to drain the pipe.

2. On the main water pipe, where you will install the filter,

use a tubing cutter to remove a section of pipe about

12" long. Use sandpaper or emery cloth to thoroughly

clean and remove all burrs and rough edges, from both

pipe ends.

NOTE: When soldering, use lead-free solder and flux

only. Be sure pipe and fittings are properly

cleaned.

3. Solder a sweat adaptor onto one of the pipe ends (See

Figure 11).

4. Place, but do not solder, a straight connector onto the

other pipe end (See Figure 11).

5. Remove the sump from the filter head and set the sump

aside.

6. After it cools, apply 4 wraps of Teflon tape to the

threads on the sweat adaptor fitting (See Figure 12).

7. With the IN side of the water filter toward incoming

water, carefully, turn the filter head onto the sweat

adaptor fitting (See Figure 12). Do not cross-thread, or

over-tighten and crack the filter head.

8. Turn a sweat adaptor fitting into the other side of the

filter head and hand tighten only. Using a tape meas-

ure or ruler, measure the distance "D" as shown in

Figure 13. Mark this same dimension on a length of

copper pipe. Cut the length of pipe.

9. Remove the sweat adaptor fitting from the filter head

and solder to the cut length of pipe.

10. After it cools, apply 4 wraps of Teflon tape to the

continued

threads on the sweat adaptor fitting. Apply flux and

place the pipe end of the soldered assembly into the

straight connector. Then, turn the adaptor end into

the filter head and tighten.

11. Solder both sides of the straight connector.

12. Before replacing the sump and turning on the water

supply, install the filter cartridge (See Page 11).

NOTE: Read the "Grounding Information" on Page 7, and

comply with the instructions if required to maintain

continuity.

\Sweat

Adaptor

Straight

Connector

Figure 11

Apply ¢_

Teflon Tape J

[_ I Filter

__ Head

Sweat

Adaptor

WATER FLOW

Figure 12

Figure 13

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

C. WATER FILTER ON HOUSE MAIN WATER PIPE, TO FILTER ALL HOUSEHOLD WATER

USING THREADED PIPE & FITTINGS (See Figure 5 on Page 6)

MATERIALS AND TOOLS NEEDED:

For threaded pipe installation, you will need a pipe

threading tool, pipe wrenches, pipe joint compound, union

fittings and pipe nipples. Connect the filter housing as

typically shown in Figure 5on Page 6.

INSTALLATION NOTES

• Use pipe joint compound on all external threads.

• Do not turn pipe or fittings too tightly into the filter

head or you may break it.

• It is important to have some linear movement in the

house main water pipe. This will allow you to tighten

union fittings without damaging the filter head, if pipe

lengths are not exact.

NOTE: Read the "Grounding Information" on Page 7, and

comply with the instructions if required to maintain

continuity.

D. WATER FILTER UNDERSINI(, TO FILTER WATER TO ONE FAUCET

(See Figure 6 on Page 6)

INSTALLATION STEPS

1. Close the cold water side shutoff valve. Usually, there

already is a shutoff under the sink. If not, close the

main water shutoff valve near the water meter or pres-

sure tank.

2. Cut and remove a section of the cold water pipe.

3. If you are plumbing with flexible tubing, hang or sup-

port the filter housing in some manner. If using rigid

pipe, be sure to allow a minimum of 2" clearance

under the filter for sump removal when changing the

filter cartridge.

4. Use the plumbing procedures on Page 7 if using com-

pression fittings. Follow procedures on Page 8 for

sweat copper and threaded pipe installation. Be sure

water flow is to the filter IN side, and from the OUT

side to the faucet.

NOTE: A grounding jumper wire is not required.

5. Before turning on the water supply, remove the sump

from the filter head and install the filter cartridge (See

Page 11).

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

Filter cartridges are available from Sears to remove:

• sediments

• tastes and odors

Many bad tastes and/or odors are reduced from water

using an activated carbon cartridge. It is most often used

to remove chlorine taste and odor.

SEDIMENT FILTER CARTRIDGES

Sediment cartridges remove sand, silt, clay, dirt and other

sediments from water.

Sediment Filter Cartridge, 25 Micron: Sears Item No. 42-

38478 (included) filters the larger sediments from water,

and allows higher flows at less pressure drop.

Sediment Filter Cartridge, 5 Micron: Sears Item No. 42-

38478 (optional) filters fine sediments from water, often

to a single faucet.

TASTE & ODOR CARTRIDGES

Sears has several optional taste and odor filter cartridges

available. These filters are used to filter the water to one

faucet and are not intended for whole house filtration.

These are:

Sears Item No. 42-34370: For reduction of chlorine taste

and odor (one faucet).

Sears Item No. 42-34365: For chlorine reduction, plus

reduction of chemical contaminants (one faucet).

Sears Item No. 42-34373: Premium taste and odor (one

faucet).

Sears Item No. 42-34377: Taste and odor, plus lead

reduction (one faucet).

Several variables determine how long a cartridge will last.

These include:

• How much water you use.

• How much sediment, taste and/or odor, or other

unwanted substance, is in the water.

Use the following information as a guide. However, no

matter which type of cartridge you are using, you will

know it is time to replace it when you first notice the

return of the unwanted substance in your water. Filter

cartridges are available from your local Sears store and

www.sears.com.

The filter cartridges require replacement 3 or 4 times a

year when used for whole house filtering. Average car-

tridge life when filtering water to one faucet is 6months

or more. This average time varies depending on the type

of cartridge and water conditions.

SEDIMENT CARTRIDGES: Filtering sediments, you will

know it's time to replace the cartridge when water pres-

sure drops at house faucets.

TASTE & ODOR CARTRIDGES: Filtering taste and odor,

you will know it's time to replace the cartridge when the

taste and odor returns. If the cartridge is also for sedi-

ment removal, you could notice a pressure drop before

the return of taste and odor.

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

Andere Handbücher für 625.384450

Inhaltsverzeichnis

Sprachen:

Andere Kenmore Wassersystem Handbücher

Kenmore

Kenmore 625.38575 Bedienungsanleitung

Kenmore

Kenmore 625.384650 Bedienungsanleitung

Kenmore

Kenmore 625.3845 Bedienungsanleitung

Kenmore

Kenmore 625.384550 Bedienungsanleitung

Kenmore

Kenmore 625.385010 Bedienungsanleitung

Kenmore

Kenmore 625.3847 Bedienungsanleitung

Kenmore

Kenmore ULTRAFILTER 300 625.384720 Bedienungsanleitung

Kenmore

Kenmore 625.385010 Bedienungsanleitung

Kenmore

Kenmore 625.75130 Bedienungsanleitung

Kenmore

Kenmore 625.381560 Bedienungsanleitung

Kenmore

Kenmore 625.347030 Bedienungsanleitung

Kenmore

Kenmore ULTRAFILTER 150 625.385700 Bedienungsanleitung

Kenmore

Kenmore 625.384650 Bedienungsanleitung

Kenmore

Kenmore 625.347001 Bedienungsanleitung

Kenmore

Kenmore 625.38156 Bedienungsanleitung

Kenmore

Kenmore 625.385560 UltraFilter 650 Bedienungsanleitung

Kenmore

Kenmore 153.331020 Bedienungsanleitung

Kenmore

Kenmore 625.385010 Bedienungsanleitung

Kenmore

Kenmore 625.385560 UltraFilter 650 Bedienungsanleitung

Kenmore

Kenmore 625.347051 Bedienungsanleitung

Kenmore

Kenmore 625.347051 Bedienungsanleitung

Kenmore

Kenmore 625.384500 Bedienungsanleitung

Kenmore

Kenmore 625.381560 Bedienungsanleitung

Kenmore

Kenmore 625.381560 Bedienungsanleitung

Beliebte Wassersystem Handbücher anderer Marken

Spirotech

Spirotech SPIROVENT SUPERIOR S250 Bedienungsanleitung

Culligan

Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Bedienungsanleitung

A.O. Smith

A.O. Smith Dura-Max AJH - 1000A - P Bedienungsanleitung

Microline

Microline T.F.C.-4 Handbuch

Eureka Forbes

Eureka Forbes Aquaguard Select Bedienungsanleitung

Cetetherm

Cetetherm AquaEfficiency Bedienungsanleitung

CB Tech

CB Tech CB-VOC Bedienungsanleitung

Vaillant

Vaillant auroFLOW plus VPM 15 D Bedienungsanleitung

resideo

resideo Braukmann HS10S Bedienungsanleitung

Gude

Gude INOX 100/24 Bedienungsanleitung

Mono

Mono Eco 1-60 Handbuch

SpectraPure

SpectraPure Drinking Water Kit Bedienungsanleitung

HydroCare

HydroCare Dual Action Bedienungsanleitung

NEXT pool

NEXT pool STERILOR Cu/Ag Verdrahtungsschema

Alpha

Alpha SolarSmart 150 Benutzerhandbuch

TA FRISTAR3 Bedienungsanleitung

GÜDE

GÜDE HWA 800 K Bedienungsanleitung

Rainfresh

Rainfresh UCS2 Bedienungsanleitung