Kenmore 625.384650 Bedienungsanleitung

OWNER'S

MANUAL

MODEL NO.

625.384650

Caution:

Read and Follow

All Safety Rules,

Installation and

Operating

Instructions

Before First Use

of This Product.

If you have questions

when installing and using

your drinking water filter

system, call this toll-free

number...

1-800 -426 -9345

www.KenmoreWater.com

SAVE THIS MANUAL

DELUXE DUAL-STAGE

DRINKING WATER SYSTEM

• Safety Guides

• Installation

• Operation

• Cartridge Replacement

• Repair Parts

System tested and certified by NSF International to

ANSl/NSF Standard 42 and 53 for the reduction of

the claims specified on the performance data sheet.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA

SAFETY GUIDES /SPECIFICATIONS

• Read all steps and guides carefully before instal-

ling and using your undersink drinking water filter

system. Follow all steps exactly to correctly install.

Reading this manual will also help you to get all the

benefits from the undersink drinking water filter

system.

•Use the filter on a potable, safe-to- drink home

COLD water supply only. The filter cartridge will

not purify water, or make it safe to drink. DO NOT

use on HOT water (100°F, max.). Do not use with

water that is microbiologically unsafe or of un-

known quality without adequate disinfection be-

fore or after the system. This system is certified for

cyst reduction and may be used on disinfected wa-

ters that may contain filterable cysts.

•Check with your local public works department

for plumbing and sanitation codes. You must fol-

low their guides as you install the system. Follow

your local codes if they differ with guides in this

manual. In Massachusetts, plumbing codes of

Massachusetts shall be adhered to. Consult with

your licensed plumber.

• The undersink drinking water filter system

works on water pressures of 30 psi (minimum) to 100

psi (maximum). If your house water pressure is over

the maximum, install a pressure reducing valve in

the water supply pipe to the filter system.

• Read the other limits (pH, hardness, etc.) in the

specifications and be sure your water supply con-

forms.

• Protect the undersink drinking water filter sys-

tem and piping from freezing. Water freezing in the

housing will break it.

Min. - Max. Supply Water Pressure

Min. - Max. Supply Water Temperature

Inlet - Outlet

Rated Service Flow

30 -100 psi

40 - 100 "F

3/8" fittings and

tubing included

0.6 gpm at 60 psi

WARRANTY

FULL ONE YEAR WARRANTY ON UNDERSINK DRINKING WATER FILTER SYSTEM

For one year from the date of purchase, Sears will replace this Undersink Drinking Water Filter System (except

filter cartridges, which are purchased separately), free of charge, if defective in material or workmanship.

WARRANTY IS AVAILABLE BY SIMPLY RETURNING THE UNDERSlNK DRINKING WATER FILTER

SYSTEM TO THE NEAREST SEARS STORE THROUGHOUT THE UNITED STATES.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Sears, Roebuck and Co., DEPT. 817 WA, Hoffman Estates, IL 60179

TABLE OF CONTENTS

Parts of the System /Typical Installation Drawing /Tools and

Materials Needed ................................................ 4

Drinking Water Filter System Installation ........................... 5 - 7

Installing Supply Fitting ..................................... 5

Installing Faucet ............................................ 5 - 6

Making Tubing Connections .................................. 7

Using the Filtered Water System ................................... 8

Filter Cartridge Life /Replacement ................................. 8 - 9

Repair Parts ................................................... 10 - 11

Locate the water filter housing on the cold water supply pipe, under the kitchen or bathroom sink, to filter the

cold drinking water. Refer to the following drawing.

FILTERING WATER TO ONE FAUCET

kitchen sink

filtered water faucet

COLD

FILTER I FILTER II

DRINKING WATER

FILTER SYSTEM

PARTS OF THE SYSTEM MATERIALS AND TOOLS NEEDED

filter system assembly including mounting brack-

et and screws

water supply fitting

filtered water faucet for sink or countertop mount-

ing

3/8" tubing to make all needed connections

• plumbers putty

• Phillips screwdrivers

• pliers and adjustable jaw wrench

• tubing cutter

• pipe joint compound or Teflon tape

• electric drill and 1" drill bit if mounting hole is

needed for the faucet, see page 6

CAUTION: To avoid damaging the sink, consult a

qualified plumber or installer for drilling procedures

in porcelain or stainless steel.

FIG. 1

TYPICAL UNDERSINK INSTALLATION

filtered water

faucet

HOT/_ COLD

shutoff valve

Note: To change the fil-

ter cartridge, you must

turn offthe water and re-

lease pressure by open-

ing the faucet. A nearby

shutoff valve is conve-

nient. Most sinks al-

ready have shutoff

valves on the supply

pipes.

supply fitting

WATER

- - _ OUT

Monitor

Cable

WATER

" _ IN

tubing

Filter IFilter II

Note: Be sure to allow a minimum space of 1- 1/2" under

the system for removing the sumps, to change the

cartridges.

15-1/2"

rain.

up from

floor

INSTALLATION STEPS

STEP 1 - COLD WATER SUPPLY FITTING

Check and comply with local plumbing codes as you plan, then install a cold feed (supply) water fitting. The

fitting must provide a leak- tight connection to the water filter 3/8" tubing. A typical connection using the in-

cluded water supply fitting is shown in FIG.2 - A. An optional connection using standard plumbing fittings

(not included), is shown in B.

A. WATER SUPPLY FITTING

1. Close the house main water shutoff valve and

open faucets to drain water from the sink cold water

pipe.

2. Remove nut that connects the cold water faucet to

cold water plumbing.

3. Use pipe joint compound or Teflon tape on cold water

faucet stud threads and on the male threads of the water

supply fitting that connect to the cold water pipe.

4. Thread water supply fitting onto pipe and reconnect

nut to bottom of fitting.

B. OPTIONAL PIPE FITTINGS

(compression type shown)

Note: Be sure to turn off the water supply and open

a low faucet to drain the pipe.

Complying with plumbing codes, install a fitting on

the cold water pipe to adapt 3 /8" OD tubing. A typi-

cal connection is shown in figure 2B. If threaded fit-

tings are used, be sure to use pipe joint compound or

Teflon tape on outside threads.

FIG. 2

A, WATER SUPPLY CONNECTION

(using included water supply fitting)

cold water t

faucet stud water supply fitting

3/8" tubing to

Water Filter inlet

co,d

_ia;eer I I

cold water

shutoff

B. WATER SUPPLY TYPICAL CONNECTION

(using compression fitting)

-parts not included -

3/8" compression

fitting insert

ferrule

cold

water

pipe

3/8" tubing to

Water Filter inlet

INSTALLATION STEPS

STEP 2 -MAKE HOLE FOR FILTERED

WATER FAUCET

Select one of the following places to install the faucet.

Be sure there's room underneath so you can make

the needed connections.

-- In an existing sink spray attachment hole.

-- Drill a hole in the sink top.

- - Drill a hole in the countertop next to the sink.

1. If drilling is needed make a 1" to 1-1/4" diameter

hole for the faucet.

CAUTION: To avoid damaging the sink, consult a

qualified plumber or installer for drilling procedures

in porcelain or stainless steel. Special drill bits are

made for this.

2. Place plumbers putty around the drilled hole to

prevent water leaks around the faucet.

FIG. 3.... .... 1" to 1- 1/4"

diameter hole

through sink or

, countertop

p,umber

putty

STEP 3 - ASSEMBLE AND

INSTALL FAUCET

1. Faucet, FIG. 4:

1. Remove the large nut from the faucet threads.

2. Slide the faucet stud and telephone style wire

through the sink or countertop hole.

3. On the underside of the sink or countertop, screw

the nut on the faucet threads with the wire running

through the slot in the washer. Tighten the nut so

the faucet cannot move, but do not overtighten.

4. Connect tubing to push to connect fitting on bot-

tom of faucet stud per instructions on page 7.

5. Connect the telephone style wire to the recepticle

on PWA board in the manifold and route the wiring

through slots in top cover and manifold assembly.

FIG. 4

ASSEMBLED IN

MOUNTING HOLE

....

plumbers

hole in sink or

countertop

faucet & spout

gasket

slotted

washer

_'_----- nut

TUBING FROM DRINKING <_:71/

WATER SYSTEM

INSTALLATION STEPS

STEP 4 -MAKE TUBING CONNECTIONS

1. Allowing some slack, measure and cut a length of

3/8" tubing to connect between the supply fitting

and the filter system inlet, FIG. 1. Cut the ends of the

tubing square.

2. Insert tubing all the way into the supply fitting and

inlet fitting. Pull on the tubing to be sure that it's

held firmly in the fitting.

3. Repeat steps I and 2 to connect tubing between the

filter system outlet and the adaptor on the bottom of

the faucet stud, FIG. 1.

TUBING CONNECTION

(all push- in fitting locations)

This system includes push- in fittings for quick tub-

ing connection at most locations. If working with the

fittings do the following.

Connection, FIG. 5 - A:

1. Use a sharp cutter or knife to cut the end of tubing

square.

2. Inspect the end (about 1") of the tubing to be sure

there are no nicks, scratches or other rough spots. If

needed cut the tubing again.

3. Push tubing through the collet and all the way into

fitting. Full engagement is 11/16" for 1/4" tubing,

and 3/4" for 3/8" tubing.

If tubing other than supplied with the system is

used, be sure it is of high quality, exact size and

roundness with a smooth surface.

To Disconnect Tubing, FIG. 5 - B: Push the collet in-

ward and hold with a finger while pulling the tubing

out.

FIG. 5 -A

Tubing correctly cut and connected

cut tubing s_uare

I I

end of tubing round and

smooth, with no cuts,

nicks or flat spots engagement -4_

_E- 3/4" (3/8" tubing) l

FIG. 5 -B

cotlet (depress to

remove tubing)

ICAUTION I

IDO NOT USE VINEGAR, OR OTHER ACID I

IBASED CLEANERS ON THIS SYSTEM. THEY I

I WILL DEGRADE SOME SYSTEM PARTS. AL- I

IWAYS USE SOAP AND WATER. I

I- .................... J

STEP 5 - FILTER CARTRIDGE INSTALLATION

Turn to page 9 and follow all steps under "Filter Cartridge Replacement".

A taste and odor cartridge contains activated carbon, a black powder. After the new cartridge is installed, open

the filtered water faucet and allow fine, harmless carbon particles to purge from the cartridge. Close the faucet

when you no longer see the "fines" in the filtered water, or approximately 2- 3 minutes.

USING THE SYSTEM

The sink or countertop faucet has a hand operated

knob to access drinking water. Turning the knob to

the left opens the faucet, turning to the fight shuts off

the faucet. Z filtered water

faucet

FAUCET ELECTRONICS

The Undersink Drinking Water Filter will monitor

the total water flow of the unit and also length of time

the filters have been installed. The faucet base has an

indicator light that flashes to inform you of the status

of the filters.

Green -Filters are good. Amber -Warning, filters

need repladng shortly. Filters need replacing, when

water has been drawn, after 168 days (or 960 gallons

have been used) since battery change. Red - Filters

must be replaced. Will flash after 14 additional days

(or 80 additional gallons).

When the two "AA" batteries are first applied at ini-

tial start up, the LED indicator light will flash in a am-

ber, green, red sequence. All timers and counters are

reset to zero.

In order to reset the monitor time and gallon count

feature, the batteries should be removed for a mini-

mum of five seconds and then reinserted.

only"AA" alkalinebatteries. Improper placement of

batteries could damage electronics. Use care when

inserting batteries to align them correctly in man-

ifold with the proper polarity.

If the faucet LED indicator light does not function af-

ter a battery change, and the batteries are known to

be good and installed properly, there may be a resid-

ual charge on the static protection device. To dissi-

pate this charge, remove the batteries for one hour.

Batteries need to be replaced once a year at the time

of filter replacement. Do not mix battery types, use

FILTER CARTRIDGE /USEFUL LIFE /REPLACEMENT

FILTER CARTRIDGE LIFE

Several variables determine how long a cartridge

will last. These include:

1. how much water you use

2. how much sediment, taste and/or odor, or other

unwanted substance, is in the water

Use the following information as a guide. However,

no matter which type of cartridge you are using, you

will know it is time to replace it when you first no-

tice the return of the unwanted substance in your

water.

Kenmore system model 625.384650 with replace-

ment elements 42-38466 has been tested and certi-

fied by NSF International for the reduction of chlo-

rine, lead, asbestos, cysts, VOC's and MTBE. The

rated capacity for this system is 1040 gallons.

FILTER CARTRIDGE REPLACEMENT

CAUTION: Never remove sumps with water pres-

sure in the filter system.

1. Close the water supply shut-off valve (FIG. 1,

page 4) to the filter. Open the filtered water faucet

to relieve pressure in the system.

2. Turn the sump off of the filter head, to the left or

clockwise 1/4 turn. Be careful, the sump is full of wa-

ter. Do not lose the large o-ring seal.

FIG. 6

ca_ridge

o-ring

seal

TURN

SUMP

CLOCKWISE

TO REMOVE

Filter I

head

TURN

SUMP

COUNTER-

CLOCKWISE

TO TIGHTEN

Filter II

3. Be sure the inside of the sump is clean. Use hot,

soapy water and rinse thoroughly.

4. Remove the wrapper from the new filter cartridge

and insert the filter cartridge in the sump. Be sure the

two o-rings are towards the filter head.

Note: If you are installing two different types of filter

cartridges, be sure to install in filters I and II as the

guideline on page 3 shows.

5. Lightly lubricate the o- ring seal in the sump with

silicone grease or Vaseline. Be sure it is fully seated

in its groove.

6. Hold the sump up to the filter head aligning the

protrusion on the cartridge with the center hole in the

bottom of the head.

Note: If the sump will not tighten up to the head you

may have the cartridge in upside down. Take the car-

tridge out and check for correct orientation.

7. Turn (counterclockwise) the sump onto the filter

head 1/4 turn.

8. Repeat steps 2 through 7 at the other filter.

9. Open the filtered water faucet. Then, slowly open

the water supply valve and allow the filter housing

to fill.

10. Close the filtered water faucet. Check for leaks be-

tween the sump and the head.

11. Remove and replace batteries to reset counter and

timer.

Note: If leaking, turn off the water supply and open

the filtered water faucet to depressurize the filter.

Then disassemble the filter and check the o-ring for

cuts, flat spots, etc., and sealing surfaces for foreign

material. Clean the o-ring and lubricate with silicone

grease or Vaseline. Carefully press the o- ring into the

groove in the sump.

12. Taste and Odor Cartridges: A taste and odor car-

tridge contains activated carbon, a black powder.

When new, open the filtered water faucet and allow

fine, harmless carbon particles to purge from the car-

tridge. Close the faucet when you no longer see the

"fines" in the filtered water, or approximately 2-3

minutes.

REPAIR PARTS

Kenmore Deluxe Dual-Stage Drinking Water System, Model No. 625.384650

Andere Handbücher für 625.384650

Inhaltsverzeichnis

Andere Kenmore Wassersystem Handbücher

Kenmore

Kenmore 625.384450 Bedienungsanleitung

Kenmore

Kenmore Elite ULTRAFILTER 650 625.38556 Bedienungsanleitung

Kenmore

Kenmore 625.347030 Bedienungsanleitung

Kenmore

Kenmore 625.384700 Bedienungsanleitung

Kenmore

Kenmore 625.385010 Bedienungsanleitung

Kenmore

Kenmore 625.384610 Bedienungsanleitung

Kenmore

Kenmore 625.347001 Bedienungsanleitung

Kenmore

Kenmore 625.381560 Bedienungsanleitung

Kenmore

Kenmore 625.38156 Bedienungsanleitung

Kenmore

Kenmore 625.381560 Bedienungsanleitung

Kenmore

Kenmore 625.384650 Bedienungsanleitung

Kenmore

Kenmore Water System Bedienungsanleitung

Kenmore

Kenmore 625.384540 Bedienungsanleitung

Kenmore

Kenmore 153.331020 Bedienungsanleitung

Kenmore

Kenmore 625.38575 Bedienungsanleitung

Kenmore

Kenmore 625.385010 Bedienungsanleitung

Kenmore

Kenmore 625.3845 Bedienungsanleitung

Kenmore

Kenmore 625.347051 Bedienungsanleitung

Kenmore

Kenmore 625.381560 Bedienungsanleitung

Kenmore

Kenmore 625.347031 Bedienungsanleitung

Kenmore

Kenmore 625.347050 Bedienungsanleitung

Kenmore

Kenmore ULTRAFILTER 300 625.384720 Bedienungsanleitung

Kenmore

Kenmore 625.385560 UltraFilter 650 Bedienungsanleitung

Kenmore

Kenmore 625.347050 Bedienungsanleitung

Beliebte Wassersystem Handbücher anderer Marken

Spirotech

Spirotech SPIROVENT SUPERIOR S250 Bedienungsanleitung

Culligan

Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Bedienungsanleitung

A.O. Smith

A.O. Smith Dura-Max AJH - 1000A - P Bedienungsanleitung

Microline

Microline T.F.C.-4 Handbuch

Eureka Forbes

Eureka Forbes Aquaguard Select Bedienungsanleitung

Cetetherm

Cetetherm AquaEfficiency Bedienungsanleitung

CB Tech

CB Tech CB-VOC Bedienungsanleitung

Vaillant

Vaillant auroFLOW plus VPM 15 D Bedienungsanleitung

resideo

resideo Braukmann HS10S Bedienungsanleitung

Gude

Gude INOX 100/24 Bedienungsanleitung

Mono

Mono Eco 1-60 Handbuch

SpectraPure

SpectraPure Drinking Water Kit Bedienungsanleitung

HydroCare

HydroCare Dual Action Bedienungsanleitung

NEXT pool

NEXT pool STERILOR Cu/Ag Verdrahtungsschema

Alpha

Alpha SolarSmart 150 Benutzerhandbuch

TA FRISTAR3 Bedienungsanleitung

GÜDE

GÜDE HWA 800 K Bedienungsanleitung

Rainfresh

Rainfresh UCS2 Bedienungsanleitung