Kenwood NX-5000 series Handbuch

NX-5000 Remote Configuration [Initial Setup Instruction]

Page | 1

Multi RF Deck / Multi Control Head

The following sections provide a step-by-step instruction on the initial set-up and configuration for the NX-5xxx-series for multiple control

heads and multiple RF decks. This includes Single Head, Single Deck.

1. Configurations

Select the appropriate configuration for the application.

# of RF Deck

Single RF Deck

Dual RF Deck

Triple RF Deck

# of Control Head

Single Head

Dual Head

Single Head

Dual Head

Single Head

Dual Head

Six Remote Mount

Configuration

Designs

NX-5000 Remote Configuration [Initial Setup Instruction]

Page | 2

2. Firmware Update

Firmware shall be updated to V1.62 or later for multi-control head / multi-deck support. The firmware shall be identical in each deck and

control head for proper operation. During set-up, the firmware shall be updated in each RF deck individually due to architecture of the radio.

This shall be done with a single deck connected to a single control head.

Assemble as follows:

NX-5000 RF Deck with KRK-15BM

KCH-19M with KRK-14HM

(If used, KCH-20RM requires no assembly)

KRK-15BM Assembly Instruction

If the radio has been previously configured for dash mounting using

the KCH-19M, remove the KCH-19M from the radio(s).

If using the NX-5xxx RF deck only then instruction 1-3 below may be skipped.

1) Lift the two tabs of the panel on the bottom of the radio with a flat-head

screwdriver and remove the panel from the chassis <Figure 1>.

2) Remove the flat cable from the display unit connector (CN6) of the panel.

3) Remove the cable from the display unit connector (CN2) of the panel.

< Figure 2 >

CN6

CN2

KCH-19M

NX-5000 Remote Configuration [Initial Setup Instruction]

Page | 3

4) Insert the cable into the connector (CN2) of the KRK-15BM <Figure 3>.

5) Insert the flat cable into the connector (CN1) of the KRK-15BM. Note: Exercise care when inserting the flat cable into CN1.

6) Fit the KRK-15BM with four tabs onto the front of the chassis. Note: Per Figure 4, the dip switch shall be on the left side as shown.

KRK-14HM Assembly Instructions

KRK-14HM is required if the basic head, KCH-19RM is used.

It is not required for the full feature control head, KCH-20RM.

1) Insert the cable into the connector (CN2) of KCH-19M.

2) Insert the flat cable into the connector (CN6) of KCH-19M.

Note: Exercise care when inserting the flat cable into CN6.

Note: The position of the flat cable needs to be inserted properly so

the traces on the cable line up with the connector CN6.

3) Fit the four tabs of the KRK-14HM into the KCH-19M. Note: Apply limited pressure to lock in position.

CAUTION:

When writing firmware for the initial setup, verify that he DIP switches (1~4) mounted on each interface adapter

(KRK-14H, KRK-15B, and KCH-20R) are set to ON.

CN2

CN1

KRK-15BM

< Figure 3 >

< Figure 4 >

CN1

< Figure 5 >

< Figure 6 >

< DIP Switch >

Dip Switch

NX-5000 Remote Configuration [Initial Setup Instruction]

Page | 4

Update Firmware and Radio Feature

Firmware shall be updated in the following items and as shown in Figure 7

to firmwareV1.62 or later.

NX-5000 RF Deck with KRK-15BM

KCH-19M with KRK-14HM

KCH-20RM

Repeat the following steps for the items noted above:

1. Connect a single RF deck with a single control head using the KCT-71 cable

as shown in Figure 8 and then power on the radio.

Note: Connect cable KCT-71 to the top connector of KRK-15BM.

2. Write Firmware

1) Start up the KFL and open the Firmware for NX-5000 series (Ver.1.62 or later).

Set the “COM Port.”. Set the “Baud Rate” to Auto.

2) Connect the radio to the PC with KPG-46UM or KPG-46XM.

3) Click the “Write”button of the KFL.

NX-5000 RF Deck

with KRK-15BM

KCH-19M

with KRK-14HM

KCH-20RM

< Figure 7 >

< Figure 8 >

NX-5000 Remote Configuration [Initial Setup Instruction]

Page | 5

4) Click the “OK”button of the following window displayed after writing is finished.

5) Confirm the firmware checksum in the LCD display to insure that the appropriate firmware has been written.

(If checksum is incorrect, then repeat from procedure 1).

6) Reboot the radio.

3. Authenticate Radio Feature License “KWD-5004MR”*

* This is necessary only for radios with S/No. B5900000 or earlier.

4. Check Firmware Version and Radio Feature License

1) Confirm that the radio’s data has the correct Firmware Version

and Activated Features using the “Transceiver Information”

of KPG-D1N.

[Firmware Version] “K 1.62.00”or later

[Activated Features］“KWD-5004MR”(Multi Receive)

2) Power off the radio and remove Head from Deck.

NX-5000 Remote Configuration [Initial Setup Instruction]

Page | 6

3. Write FPU Data

For Single RF Deck Configuration

1. Launch KPG-D1N

2. Create FPU Data file

1) If using an existing data file, open the file.

2) Open Product Information.

3) Select Control Head 1 and Control Head 2.

4) Program additional settings.

NX-5000 Remote Configuration [Initial Setup Instruction]

Page | 7

3. Write FPU Data file

1) Power on the radio.

2) Connect the radio to the PC with the KPG-46 Cable via Control Head 1.

3) Write the FPU Data to the radio by clicking the “Write” button of KPG-D1N.

4) Power off the radio.

NX-5000 Remote Configuration [Initial Setup Instruction]

Page | 8

For Multi RF Deck Configuration

1. Launch KPG-D1N

2. Create FPU Data file for each RF Deck separately

Note: Repeat this procedure for each RF Deck separately.

1) If applying existing data file to Multi RF Deck, open the data file.

2) Open Product Information and enable the Multi RF Deck Feature Selection.

NX-5000 Remote Configuration [Initial Setup Instruction]

Page | 9

3) Select Control Head 1 and Control Head 2.

4) Program additional settings.

Note: At least one channel shall be programmed.

5) Save the data file.

3. Select FPU Data file for Multi RF Deck

1) Program > Multi RF Deck Setup

NX-5000 Remote Configuration [Initial Setup Instruction]

Page | 10

2) Assign all of the FPU Data saved for each RF Deck to RF Deck Data A/B/C by clicking each Select File button.

Note: If following window is displayed when FPU Data is opened, press OK Button.

Andere Handbücher für NX-5000 series

Andere Kenwood Empfänger Handbücher

Kenwood

Kenwood KRF-V6400D Bedienungsanleitung

Kenwood

Kenwood KR-V7070 Bedienungsanleitung

Kenwood

Kenwood KR-X1000 Bedienungsanleitung

Kenwood

Kenwood QR-666 Bedienungsanleitung

Kenwood

Kenwood KMM-BT358 Bedienungsanleitung

Kenwood

Kenwood VR-50RS Bedienungsanleitung

Kenwood

Kenwood KMM-BT203 Bedienungsanleitung

Kenwood

Kenwood KAT002ME Leitfaden

Kenwood

Kenwood KR-V990D Bedienungsanleitung

Kenwood

Kenwood DDX9904S Bedienungsanleitung

Kenwood

Kenwood KMM-205 Bedienungsanleitung

Kenwood

Kenwood KR-V8540 Bedienungsanleitung

Kenwood

Kenwood VR-405 Bedienungsanleitung

Kenwood

Kenwood R-2000 Bedienungsanleitung

Kenwood

Kenwood AR-404 Bedienungsanleitung

Kenwood

Kenwood KSR-1000 Bedienungsanleitung

Kenwood

Kenwood 107VR Bedienungsanleitung

Kenwood

Kenwood KRF-V9993D Bedienungsanleitung

Kenwood

Kenwood KMM- BT508DAB Bedienungsanleitung

Kenwood

Kenwood KRF-V4550D Bedienungsanleitung

Kenwood

Kenwood KRF-X9992D Bedienungsanleitung

Kenwood

Kenwood KMM-122 Bedienungsanleitung

Kenwood

Kenwood KR-A4020 Bedienungsanleitung

Kenwood

Kenwood KR-V6070 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung