Kenwood Nexedge NX-300GE Bedienungsanleitung

NX-200G/ NX-300G

VHF DIGITAL TRANSCEIVER/

UHF DIGITAL TRANSCEIVER

INSTRUCTION MANUAL

B5A-0160-10 (E)

ABC

JKL

TUV

GHI

PQRS

DEF

MNO

MIC

WXYZ

THANK YOU

We are grateful you have chosen KENWOOD for your land

mobile radio applications.

NOTICES TO THE USER

◆Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆Illegal operation is punishable by ﬁne and/or imprisonment.

◆Refer service to qualiﬁed technicians only.

Safety: It is important that the operator is aware of and

understands hazards common to the operation of any

transceiver.

Firmware Copyrights

The title to and ownership of copyrights for ﬁrmware

embedded in KENWOOD product memories are reserved

for JVC KENWOOD Corporation.

PRECAUTIONS

• Do not charge the transceiver and battery pack when they are wet.

• Ensure that there are no metallic items located between the

transceiver and the battery pack.

• Do not use options not speciﬁed by KENWOOD.

• If the die-cast chassis or other transceiver part is damaged, do not

touch the damaged parts.

• If a headset or headphone is connected to the transceiver, reduce

the transceiver volume. Pay attention to the volume level when

turning the squelch off.

• Do not place the microphone cable around your neck while near

machinery that may catch the cable.

• Do not place the transceiver on unstable surfaces.

• Ensure that the end of the antenna does not touch your eyes.

• When the transceiver is used for transmission for many hours, the

radiator and chassis will become hot. Do not touch these locations

when replacing the battery pack.

• Always switch the transceiver power off before installing optional

accessories.

• The charger is the device that disconnects the unit from the AC

mains line. The AC plug should be readily accessible.

iii

Turn the transceiver power off in the following locations:

• Near explosives or blasting sites.

• In aircrafts. (Any use of the transceiver must follow the

instructions and regulations provided by the airline crew.)

• Where restrictions or warnings are posted regarding the use of

radio devices, including but not limited to medical facilities.

• Near persons wearing pacemakers.

Turn the transceiver power off in the following locations,

unless the model is speciﬁcally qualiﬁed for such use

(Intrinsically Safe such as approved by Factory Mutual, CSA):

• In explosive atmospheres (inﬂammable gas, dust particles,

metallic powders, grain powders, etc.).

• While taking on fuel or while parked at gasoline service stations.

• Do not remove the black sheet from the reverse side of the

transceiver (refer to the illustration below). Removal of this

sheet decreases the waterproof efﬁciency of the transceiver and

may cause malfunctions if water seeps into the transceiver.

• The orange seal on the reverse side of the transceiver is

important with respect to the waterproof efﬁciency of the

transceiver. Do not place stickers or other materials on or

around the seal shown in the ﬁgure, or on the reverse side of

the battery pack. Doing so will impair the waterproof efﬁciency

of the transceiver and may cause it to break down. Additionally,

in order to prevent damage to the seal, do not allow it to come

in contact with foreign materials.

• Do not disassemble or modify the transceiver for any reason.

• Do not place the transceiver on or near airbag equipment while

the vehicle is running. When the airbag inﬂates, the transceiver

may be ejected and strike the driver or passengers.

• Do not transmit while touching the antenna terminal or if

any metallic parts are exposed from the antenna covering.

Transmitting at such a time may result in a high-frequency burn.

• If an abnormal odor or smoke is detected coming from the

transceiver, switch the transceiver power off immediately,

remove the battery pack from the transceiver, and contact your

KENWOOD dealer.

• Use of the transceiver while you are driving may be against

trafﬁc laws. Please check and observe the vehicle regulations

in your area.

• Do not expose the transceiver to extremely hot or cold

conditions.

• Do not carry the battery pack (or battery case) with metal

objects, as they may short the battery terminals.

• Danger of explosion if the battery is incorrectly replaced;

replace only with the same type.

• When attaching a commercial strap to the transceiver, ensure

that the strap is durable. In addition, do not swing the transceiver

around by the strap; you may inadvertently strike and injure

another person with the transceiver.

• If a commercially available neck strap is used, take care not to

let the strap get caught on nearby machine.

• When operating the transceiver in areas where the air is dry,

it is easy to build up an electric charge (static electricity).

When using an earphone accessory in such conditions, it is

possible for the transceiver to send an electric shock through

the earphone and to your ear. We recommend you use only

a speaker/microphone in these conditions, to avoid electric

shocks.

NOTIFICATION OF WATER-RESISTANT MODEL

Water Resistance and Maintenance

This transceiver conforms to the following standards:

IP67: The IP standard is the protection level speciﬁed by the

international standard IEC 60529. The ﬁrst numeral indicates the “dust-

resistant” level and the second numeral indicates the “water-resistant”

level.

PRECAUTIONS

• The applicable standards listed above do not assure that the

transceiver can be used in water. The transceiver may be

damaged in a situation in which the maximum depth is over

1 meter or the maximum submersion time exceeds 30 minutes.

• Observe the following precautions to maintain the transceiver’s

water-resistant performance:

a) Do not drop or apply strong physical shocks to the transceiver.

b) When you disassemble the transceiver or open the cover of

the option board, IP67 will no longer be maintained. After

disassembling the transceiver or opening the cover of the

option board, if you want to continue maintaining IP67, contact

your dealer or Authorized Service Center.

c) Do not soak the transceiver in water that contains a solvent or

surfactant, such as detergent or alcohol.

• If it is soaked in muddy water or salt water (including sea water),

it may become corroded. Immediately ﬂush with fresh water and

then wipe dry with a soft cloth.

• If water is splashed onto the microphone, the battery, or the

antenna terminal, clean and dry them with a soft cloth before

reconnecting to the transceiver.

• When water gets into the microphone opening or the speaker

grill, the voice level may become low or distorted. Lightly shake

the transceiver to remove the water from the speaker and/or

microphone before operating the transceiver.

• Use of any option on the transceiver not speciﬁed by KENWOOD,

may reduce or void the water resistant and dust resistant

performance.

• When using an option with the transceiver, ensure that it

corresponds with the IP67 standard.

INFORMATION CONCERNING THE LI-ION BATTERY PACK:

The battery pack includes ﬂammable objects such as organic solvent.

Mishandling may cause the battery to rupture producing ﬂames or

extreme heat, deteriorate, or cause other forms of damage to the

battery. Please observe the following prohibitive matters.

• Do not disassemble or reconstruct battery!

The battery pack has a safety function and protection circuit to

avoid danger. If they suffer serious damage, the battery may

generate heat or smoke, rupture, or burst into ﬂame.

• Do not short-circuit the battery!

Do not join the + and – terminals using any form of metal (such

as a paper clip or wire). Do not carry or store the battery pack

in containers holding metal objects (such as wires, chain-

necklace or hairpins). If the battery pack is short-circuited,

excessive current will ﬂow and the battery may generate heat

or smoke, rupture, or burst into ﬂame. It will also cause metal

objects to heat up.

• Do not incinerate or apply heat to the battery!

If the insulator is melted, the gas release vent or safety function

is damaged, or the electrolyte is ignited, the battery may

generate heat or smoke, rupture, or burst into ﬂame.

• Do not leave the battery near ﬁres, stoves, or other heat

generators (areas reaching over 80°C/ 176°F)!

If the polymer separator is melted due to high temperature,

an internal short-circuit may occur in the individual cells and

the battery may generate heat or smoke, rupture, or burst into

ﬂame.

• Avoid immersing the battery in water or getting it wet by

other means!

If the battery becomes wet, wipe it off with a dry towel before

use. If the battery’s protection circuit is damaged, the battery

may charge at extreme current (or voltage) and an abnormal

chemical reaction may occur. The battery may generate heat or

smoke, rupture, or burst into ﬂame.

vii

• Do not charge the battery near ﬁres or under direct

sunlight!

If the battery’s protection circuit is damaged, the battery

may charge at extreme current (or voltage) and an abnormal

chemical reaction may occur. The battery may generate heat or

smoke, rupture, or burst into ﬂame.

• Use only the speciﬁed charger and observe charging

requirements!

If the battery is charged in unspeciﬁed conditions (under high

temperature over the regulated value, excessive high voltage or

current over regulated value, or with a remodelled charger), it

may overcharge or an abnormal chemical reaction may occur.

The battery may generate heat or smoke, rupture, or burst into

ﬂame.

• Do not pierce the battery with any object, strike it with an

instrument, or step on it!

This may break or deform the battery, causing a short-circuit.

The battery may generate heat or smoke, rupture, or burst into

ﬂame.

• Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat

or smoke, rupture, and/or burst into ﬂame. If the battery’s

protection circuit is damaged, the battery may charge at an

abnormal current (or voltage), and an abnormal chemical

reaction may occur.

• Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

ﬂame.

• Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety

function is damaged, the battery may generate heat or smoke,

rupture, or burst into ﬂame.

• Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical

reaction may occur. In some cases, an unexpected large

amount of current may ﬂow upon discharging. The battery may

generate heat or smoke, rupture, or burst into ﬂame.

viii

• Do not charge the battery for longer than the speciﬁed

time!

If the battery pack has not ﬁnished charging even after the

regulated time has passed, stop it. The battery may generate

heat or smoke, rupture, or burst into ﬂame.

• Do not place the battery pack into a microwave or high

pressure container!

The battery may generate heat or smoke, rupture, or burst into

ﬂame.

• Keep ruptured and leaking battery packs away from ﬁre!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from ﬂammable areas. Electrolyte

leaking from battery can easily catch on ﬁre and may cause the

battery to generate smoke or burst into ﬂame.

• Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have color

changes, is deformed, or seems abnormal for any other reason,

remove it from the charger or operating equipment and do not

use it. The battery may generate heat or smoke, rupture, or

burst into ﬂame.

• Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating

equipment, do not force it; check the polarity of the battery. If

the battery pack is reverse-connected to the charger, it will be

reverse-charged and an abnormal chemical reaction may occur.

The battery may generate heat or smoke, rupture, or burst into

ﬂame.

• Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes,

wash your eyes out with fresh water as soon as possible,

without rubbing your eyes. Go to the hospital immediately. If

left untreated, it may cause eye-problems.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kenwood Transceiver Handbücher

Kenwood

Kenwood NX-3400 Bedienungsanleitung

Kenwood

Kenwood TS-870S Bedienungsanleitung

Kenwood

Kenwood TS-670 Bedienungsanleitung

Kenwood

Kenwood TM-251A Bedienungsanleitung

Kenwood

Kenwood TK-7100 Bedienungsanleitung

Kenwood

Kenwood UBZ-LJ8 Bedienungsanleitung

Kenwood

Kenwood TM-631A Bedienungsanleitung

Kenwood

Kenwood TK-8100 Bedienungsanleitung

Kenwood

Kenwood TK-7102 Bedienungsanleitung

Kenwood

Kenwood TS-450S Bedienungsanleitung

Kenwood

Kenwood TS-430S Bedienungsanleitung

Kenwood

Kenwood TK-780 series Bedienungsanleitung

Kenwood

Kenwood TH-K2AT Bedienungsanleitung

Kenwood

Kenwood TS-990S Bedienungsanleitung

Kenwood

Kenwood TS-850S Bedienungsanleitung

Kenwood

Kenwood TS-440S Bedienungsanleitung

Kenwood

Kenwood TS-530S Bedienungsanleitung

Kenwood

Kenwood TM-3530A Bedienungsanleitung

Kenwood

Kenwood TM-231E Bedienungsanleitung

Kenwood

Kenwood TR-7400A Bedienungsanleitung

Kenwood

Kenwood TS-950SDX Bedienungsanleitung

Kenwood

Kenwood TK-290 Bedienungsanleitung

Kenwood

Kenwood TH-28A Bedienungsanleitung

Kenwood

Kenwood PKT-23 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung

Standard Horizon

Standard Horizon HX320E Bedienungsanleitung

Em-Trak

Em-Trak A100 Bedienungsanleitung

HPE

HPE Aruba QSFP28 Bedienungsanleitung

RADTEL

RADTEL RT-490 Bedienungsanleitung