Kenwood TK-2300-V4P - Protalk 2Way 2Watt 4Channel Vhf... Bedienungsanleitung

INSTRUCTION MANUAL

09 08 07 06 05 04 03 02 01 00

VHF FM TRANSCEIVER

TK-2300

UHF FM TRANSCEIVER

TK-3300

Thank You

We are grateful for your purchase of this Kenwood product and

welcome you to the Business Radio Service (BRS).

Your Kenwood 2-way Business Radio is called a “transceiver”,

meaning “transmitter & receiver”. We believe this easy-to-

use transceiver will provide you with dependable and reliable

communications. This Kenwood transceiver is a precision

device. Treat it with care, and you will enjoy years of reliable

operation.

Models Covered bY This Manual

TK-2300 (K): 4-channel VHF FM Transceiver

TK-3300 (K): 4-channel UHF FM Transceiver

TK-2300 (K2): 16-channel VHF FM Transceiver

TK-3300 (K2): 16-channel UHF FM Transceiver

FeaTures

• 4 channels (K) or 16 channels (K2) with 27 VHF operating

frequencies (TK-2300) or 89 UHF operating frequencies

(TK-3300) and 122 tone/ code settings for each channel

allowing you to ignore unwanted calls.

• Built in voice scrambler gives you complete privacy for your

conversations.

• Hands free operation when using an optional headset.

• Voice announcement lets you know which channel you have

selected and which settings you have made when reassigning

key functions and channel settings.

Operating COnditiOns

Open locations (no obstructions) Up to 6 miles (9.6 km)

Residential areas (near buildings) Up to 1.5 miles (2.4 km)

In steel/ concrete reinforced

buildings

Up to 250,000 square feet

(23,220 m2)

In high rises Up to 20 floors

Note: The listed ranges are based on field testing and may vary with

your operating conditions and individual transceiver.

Terminal Descriptions

Speaker/ Microphone Jacks

It is possible to use a resin-based cover for the Speaker/ Microphone jacks.

NO. Name Description Impedance I/O

1 PTT / RXD External PTT Input / Serial

Data Input CMOS I

2 MIC External MIC Input 1.8 kΩ I

3 MICIN Internal MIC Output 1.8 kΩ O

4 OPTDET External Option Detect High Impedance I

5 5M 5V Output 100 Ω O

6 AE GND GND −

7 TXD Serial Data Output CMOS O

8 NC No Connection − −

9 SPO Audio Input 8 Ω I

10 SPI Received Audio Output 8 Ω O

Antenna Terminal

50 Ω impedance

Battery Terminal

The battery terminal uses a spring plate.

The negative terminal connects to the chassis ground.

The battery is mounted on the rear side of the transceiver using a latch

mounting method.

FCC LiCense inFOrmatiOn

Your Kenwood transceiver operates on communications

frequencies which are subject to FCC (Federal Communications

Commission) Rules & Regulations. FCC Rules require that all

operators using Private Land Mobile radio frequencies obtain a

radio license before operating their equipment. Application for

license must be made on FCC form 601, schedules D and H,

and Remittance form 159.

FAX: Forms can be obtained by fax from the FCC Fax-On-

Demand system. Call 1-202-418-0177 from your fax machine

and request document number 000601 for the form, schedules,

and instructions.

MAIL: Forms can be ordered by telephone, and will be sent to

you by first class mail. Call the FCC Forms Hotline at

1-800-418-FORM (1-800-418-3676).

INTERNET: Form 601 and instructions can be downloaded

from the FCC Forms website at

http://www.fcc.gov/formpage.html

Before filling out your Form 601 application Technical Data

section, you must decide on which frequencies you will operate.

See the frequency charts on pages 14 and 15.

QUESTIONS? Call the FCC for license application questions

at 1-888-CALL-FCC (1-888-225-5322).

iii

One or more of the following statements may be

applicable:

FCC WARNING

This equipment generates or uses radio frequency energy. Changes

or modifications to this equipment may cause harmful interference

unless the modifications are expressly approved in the instruction

manual. The user could lose the authority to operate this equipment if

an unauthorized change or modification is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY

THE FCC

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency

energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that the interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from that

to which the receiver is connected.

•Consult the dealer for technical assistance.

ATTENTION:

The RBRC Recycle seal found on Kenwood lithium-ion

(Li-ion) battery packs indicates Kenwood’s voluntary

participation in an industry program to collect and recycle

Li-ion batteries after their operating life has expired.

The RBRC program is an alternative to disposing Li-ion

batteries with your regular refuse or in municipal waste

streams, which is illegal in some areas.

For information on Li-ion battery recycling in your area, call (toll free)

1-800-8-BATTERY (1-800-822-8837).

Kenwood’s involvement in this program is part of our commitment to

preserve our environment and conserve our natural resources.

nOtiCes tO the User

◆Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆Illegal operation is punishable by fine and/or imprisonment.

◆Refer service to qualified technicians only.

Safety: It is important that the operator is aware of, and

understands, hazards common to the operation of any

transceiver.

preCaUtiOns

• Do not charge the transceiver and battery pack when they are wet.

• Ensure that there are no metallic items located between the

transceiver and the battery pack.

• Do not use options not specified by Kenwood.

• If the die-cast chassis or other transceiver part is damaged, do not

touch the damaged parts.

• If a headset or headphone is connected to the transceiver, reduce

the transceiver volume. Pay attention to the volume level when

turning the squelch off.

• Do not place the microphone cable around your neck while near

machinery that may catch the cable.

• Do not place the transceiver on unstable surfaces.

• Ensure that the end of the antenna does not touch your eyes.

• When the transceiver is used for transmission for many hours, the

radiator and chassis will become hot. Do not touch these locations

when replacing the battery pack.

• Do not immerse the transceiver in water.

• Always switch the transceiver power off before installing optional

accessories.

• The charger is the device that disconnects the unit from the AC

mains line. The AC plug should be readily accessible.

Turn the transceiver power off in the following locations:

• In explosive atmospheres (inflammable gas, dust particles,

metallic powders, grain powders, etc.).

• While taking on fuel or while parked at gasoline service stations.

• Near explosives or blasting sites.

• In aircrafts. (Any use of the transceiver must follow the instructions

and regulations provided by the airline crew.)

• Where restrictions or warnings are posted regarding the use of

radio devices, including but not limited to medical facilities.

• Near persons using pacemakers.

• Do not disassemble or modify the transceiver for any reason.

• Do not place the transceiver on or near airbag equipment while

the vehicle is running. When the airbag inflates, the transceiver

may be ejected and strike the driver or passengers.

• Do not transmit while touching the antenna terminal or if

any metallic parts are exposed from the antenna covering.

Transmitting at such a time may result in a high-frequency burn.

• If an abnormal odor or smoke is detected coming from the

transceiver, switch the transceiver power off immediately, remove

the battery pack from the transceiver, and contact your Kenwood

dealer.

• Use of the transceiver while you are driving may be against traffic

laws. Please check and observe the vehicle regulations in your

area.

• Do not expose the transceiver to extremely hot or cold conditions.

• Do not carry the battery pack (or battery case) with metal objects,

as they may short the battery terminals.

• Danger of explosion if the battery is incorrectly replaced; replace

only with the same type.

• When operating the transceiver in areas where the air is dry, it is

easy to build up an electric charge (static electricity). When using

an earphone accessory in such conditions, it is possible for the

transceiver to send an electric shock through the earphone and to

your ear. We recommend you use only a speaker/microphone in

these conditions, to avoid electric shocks.

Information concerning the battery pack:

The battery pack includes flammable objects such as organic

solvent. Mishandling may cause the battery to rupture

producing flames or extreme heat, deteriorate, or cause other

forms of damage to the battery. Please observe the following

prohibitive matters.

• Do not disassemble or reconstruct battery!

The battery pack has a safety function and protection circuit to

avoid danger. If they suffer serious damage, the battery may

generate heat or smoke, rupture, or burst into flame.

• Do not short-circuit the battery!

Do not join the + and – terminals using any form of metal (such

as a paper clip or wire). Do not carry or store the battery pack in

containers holding metal objects (such as wires, chain-necklace or

hairpins). If the battery pack is short-circuited, excessive current will

flow and the battery may generate heat or smoke, rupture, or burst

into flame. It will also cause metal objects to heat up.

• Do not incinerate or apply heat to the battery!

If the insulator is melted, the gas release vent or safety function is

damaged, or the electrolyte is ignited, the battery may generate

heat or smoke, rupture, or burst into flame.

• Do not use or leave the battery near fire, stoves, or other heat

generators (areas reaching over 80°C/ 176°F)!

If the polymer separator is melted due to high temperature, an

internal short-circuit may occur in the individual cells and the

battery may generate heat or smoke, rupture, or burst into flame.

• Do not immerse the battery in water or get it wet by other

means!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke,

rupture, or burst into flame.

• Do not charge the battery near fire or under direct sunlight!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke,

rupture, or burst into flame.

vii

• Use only the specified charger and observe charging

requirements!

If the battery is charged in unspecified conditions (under high

temperature over the regulated value, excessive high voltage or

current over regulated value, or with a remodeled charger), it may

overcharge or an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not pierce the battery with any object, strike it with an

instrument, or step on it!

This may break or deform the battery, causing a short-circuit. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat or smoke,

rupture, and/or burst into flame. If the battery’s protection circuit

is damaged, the battery may charge at an abnormal current (or

voltage), and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

flame.

• Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety function

is damaged, the battery may generate heat or smoke, rupture, or

burst into flame.

• Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical reaction

may occur. In some cases, an unexpected large amount of

current may flow upon discharging. The battery may generate

heat or smoke, rupture, or burst into flame.

• Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating

equipment, do not force it; check the polarity of the battery. If the

battery pack is reverse-connected to the charger, it will be reverse-

charged and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

viii

• Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes, wash

your eyes with fresh water as soon as possible, without rubbing

your eyes. Go to the hospital immediately. If left untreated, it may

cause eye-problems.

• Do not charge the battery for longer than the specified time!

If the battery pack has not finished charging even after the

regulated time has passed, stop it. The battery may generate heat

or smoke, rupture, or burst into flame.

• Do not place the battery pack into a microwave or high

pressure container!

The battery may generate heat or smoke, rupture, or burst into

flame.

• Keep ruptured and leaking battery packs away from fire!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from flammable areas. Electrolyte leaking

from battery can easily catch on fire and may cause the battery to

generate smoke or burst into flame.

• Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have different

coloring, is deformed, or seems abnormal for any other reason,

remove it from the charger or operating equipment and do not use

it. The battery may generate heat or smoke, rupture, or burst into

flame.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kenwood Transceiver Handbücher

Kenwood

Kenwood TK-780 series Bedienungsanleitung

Kenwood

Kenwood NX-203 Bedienungsanleitung

Kenwood

Kenwood NEXEDGE NX-720 Bedienungsanleitung

Kenwood

Kenwood TK-8100 Bedienungsanleitung

Kenwood

Kenwood TS-940S Bedienungsanleitung

Kenwood

Kenwood TS-700A Bedienungsanleitung

Kenwood

Kenwood TK-7180 Einrichtungshandbuch

Kenwood

Kenwood TH-K40A Bedienungsanleitung

Kenwood

Kenwood TM-641A Bedienungsanleitung

Kenwood

Kenwood NX-1200A Bedienungsanleitung

Kenwood

Kenwood TK-3400 Bedienungsanleitung

Kenwood

Kenwood TM-V71E Bedienungsanleitung

Kenwood

Kenwood TK-3160 Bedienungsanleitung

Kenwood

Kenwood TK-480 Bedienungsanleitung

Kenwood

Kenwood TK-5210 Bedienungsanleitung

Kenwood

Kenwood TK-2317 Bedienungsanleitung

Kenwood

Kenwood TS-670 Bedienungsanleitung

Kenwood

Kenwood TK-2200 Bedienungsanleitung

Kenwood

Kenwood TK-7108 Bedienungsanleitung

Kenwood

Kenwood PKT-23 Bedienungsanleitung

Kenwood

Kenwood TS-770 Bedienungsanleitung

Kenwood

Kenwood TH-225A Bedienungsanleitung

Kenwood

Kenwood ProTalk tk-3501 Bedienungsanleitung

Kenwood

Kenwood TK-5910 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung

Standard Horizon

Standard Horizon HX320E Bedienungsanleitung

Em-Trak

Em-Trak A100 Bedienungsanleitung

HPE

HPE Aruba QSFP28 Bedienungsanleitung

RADTEL

RADTEL RT-490 Bedienungsanleitung