Kenwood TK-2302 Bedienungsanleitung

TK-2302/ TK-2302V

TK-3302/ TK-3302U

09 08 07 06 05 04 03 02 01 00

VHF FM TRANSCEIVER/

UHF FM TRANSCEIVER

INSTRUCTION MANUAL

ÉMETTEUR-RÉCEPTEUR FM VHF/

ÉMETTEUR-RÉCEPTEUR FM UHF

MODE D’EMPLOI

TRANSCEPTOR FM VHF/

TRANSCEPTOR FM UHF

MANUAL DE INSTRUCCIONES

VHF FM TRANSCEIVER/

UHF FM TRANSCEIVER

TK-2302/ TK-2302V

TK-3302/ TK-3302U

INSTRUCTION MANUAL

ENGLISH

ATTENTION:

The RBRC Recycle seal found on Kenwood lithium-ion

(Li-ion) battery packs indicates Kenwood’s voluntary

participation in an industry program to collect and recycle

Li-ion batteries after their operating life has expired.

The RBRC program is an alternative to disposing Li-ion

batteries with your regular refuse or in municipal waste

streams, which is illegal in some areas.

For information on Li-ion battery recycling in your area, call (toll free)

1-800-8-BATTERY (1-800-822-8837).

Kenwood’s involvement in this program is part of our commitment to

preserve our environment and conserve our natural resources.

ATTENTION:

The RBRC Recycle seal found on Kenwood nickel

metal hydride (Ni-MH) battery packs indicates Kenwood’

s voluntary participation in an industry program to collect

and recycle Ni-MH batteries after their operating life

has expired. The RBRC program is an alternative to

disposing Ni-MH batteries with your regular refuse or in

municipal waste streams, which is illegal in some areas.

For information on Li-ion battery recycling in your area, call (toll free)

1-800-8-BATTERY (1-800-822-8837).

Kenwood’s involvement in this program is part of our commitment to

preserve our environment and conserve our natural resources.

Thank You

We are grateful you have chosen Kenwood for your land

mobile radio applications.

noTices To The user

◆Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆Illegal operation is punishable by fine and/or imprisonment.

◆Refer service to qualified technicians only.

Safety: It is important that the operator is aware of, and

understands, hazards common to the operation of any

transceiver.

Terminal Descriptions

Speaker/ Microphone Jacks

It is possible to use a resin-based cover for the Speaker/ Microphone jacks.

NO. Name Description Impedance I/O

1 PTT / RXD External PTT Input / Serial

Data Input CMOS I

2 MIC External MIC Input 1.8 kΩ I

3 MICIN Internal MIC Output 1.8 kΩ O

4 OPTDET External Option Detect High Impedance I

5 5M 5V Output 100 Ω O

6 AE GND GND −

7 TXD Serial Data Output CMOS O

8 NC No Connection − −

9 SPO Audio Input 8 Ω I

10 SPI Received Audio Output 8 Ω O

Antenna Terminal

50 Ω impedance

Battery Terminal

The battery terminal uses a spring plate.

The negative terminal connects to the chassis ground.

The battery is mounted on the rear side of the transceiver using a latch

mounting method.

One or more of the following statements may be

applicable:

FCC WARNING

This equipment generates or uses radio frequency energy.

Changes or modifications to this equipment may cause harmful

interference unless the modifications are expressly approved in the

instruction manual. The user could lose the authority to operate this

equipment if an unauthorized change or modification is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY

THE FCC

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation.

This equipment generates, uses and can generate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur

in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment to an outlet on a circuit different from

that to which the receiver is connected.

•

Consult the dealer for technical assistance.

PrecauTions

• Do not charge the transceiver and battery pack when they are wet.

• Ensure that there are no metallic items located between the

transceiver and the battery pack.

• Do not use options not specified by Kenwood.

• If the die-cast chassis or other transceiver part is damaged, do not

touch the damaged parts.

• If a headset or headphone is connected to the transceiver, reduce

the transceiver volume. Pay attention to the volume level when

turning the squelch off.

• Do not place the microphone cable around your neck while near

machinery that may catch the cable.

• Do not place the transceiver on unstable surfaces.

• Ensure that the end of the antenna does not touch your eyes.

• When the transceiver is used for transmission for many hours, the

radiator and chassis will become hot. Do not touch these locations

when replacing the battery pack.

• Do not immerse the transceiver in water.

• Always switch the transceiver power off before installing optional

accessories.

• The charger is the device that disconnects the unit from the AC

mains line. The AC plug should be readily accessible.

iii

Turn the transceiver power off in the following locations:

• In explosive atmospheres (inflammable gas, dust particles, metallic

powders, grain powders, etc.).

• While taking on fuel or while parked at gasoline service stations.

• Near explosives or blasting sites.

• In aircrafts. (Any use of the transceiver must follow the instructions

and regulations provided by the airline crew.)

• Where restrictions or warnings are posted regarding the use of

radio devices, including but not limited to medical facilities.

• Near persons using pacemakers.

• Do not disassemble or modify the transceiver for any reason.

• Do not place the transceiver on or near airbag equipment while the

vehicle is running. When the airbag inflates, the transceiver may

be ejected and strike the driver or passengers.

• Do not transmit while touching the antenna terminal or if any

metallic parts are exposed from the antenna covering. Transmitting

at such a time may result in a high-frequency burn.

• If an abnormal odor or smoke is detected coming from the

transceiver, switch the transceiver power off immediately, remove

the battery pack from the transceiver, and contact your Kenwood

dealer.

• Use of the transceiver while you are driving may be against traffic

laws. Please check and observe the vehicle regulations in your

area.

• Do not expose the transceiver to extremely hot or cold conditions.

• Do not carry the battery pack (or battery case) with metal objects,

as they may short the battery terminals.

• When operating the transceiver in areas where the air is dry, it is

easy to build up an electric charge (static electricity). When using

a earphone accessory in such conditions, it is possible for the

transceiver to send an electric shock through the earphone and to

your ear. We recommend you use only a speaker/microphone in

these conditions, to avoid electric shocks.

Information concerning the battery pack:

The battery pack includes flammable objects such as organic

solvent. Mishandling may cause the battery to rupture

producing flames or extreme heat, deteriorate, or cause other

forms of damage to the battery. Please observe the following

prohibitive matters.

• Do not disassemble or reconstruct battery!

The battery pack has a safety function and protection circuit to

avoid danger. If they suffer serious damage, the battery may

generate heat or smoke, rupture, or burst into flame.

• Do not short-circuit the battery!

Do not join the + and – terminals using any form of metal (such

as a paper clip or wire). Do not carry or store the battery pack in

containers holding metal objects (such as wires, chain-necklace or

hairpins). If the battery pack is short-circuited, excessive current will

flow and the battery may generate heat or smoke, rupture, or burst

into flame. It will also cause metal objects to heat up.

• Do not incinerate or apply heat to the battery!

If the insulator is melted, the gas release vent or safety function is

damaged, or the electrolyte is ignited, the battery may generate

heat or smoke, rupture, or burst into flame.

• Do not use or leave the battery near fire, stoves, or other heat

generators (areas reaching over 80°C/ 176°F)!

If the polymer separator is melted due to high temperature, an

internal short-circuit may occur in the individual cells and the

battery may generate heat or smoke, rupture, or burst into flame.

• Do not immerse the battery in water or get it wet by other

means!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke,

rupture, or burst into flame.

• Do not charge the battery near fire or under direct sunlight!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke,

rupture, or burst into flame.

• Use only the specified charger and observe charging

requirements!

If the battery is charged in unspecified conditions (under high

temperature over the regulated value, excessive high voltage or

current over regulated value, or with a remodeled charger), it may

overcharge or an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not pierce the battery with any object, strike it with an

instrument, or step on it!

This may break or deform the battery, causing a short-circuit. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat or smoke,

rupture, and/or burst into flame. If the battery’s protection circuit

is damaged, the battery may charge at an abnormal current (or

voltage), and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

flame.

• Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety function

is damaged, the battery may generate heat or smoke, rupture, or

burst into flame.

• Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical reaction

may occur. In some cases, an unexpected large amount of current

may flow upon discharging. The battery may generate heat or

smoke, rupture, or burst into flame.

• Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating

equipment, do not force it; check the polarity of the battery. If the

battery pack is reverse-connected to the charger, it will be reverse-

charged and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes, wash

your eyes with fresh water as soon as possible, without rubbing

your eyes. Go to the hospital immediately. If left untreated, it may

cause eye-problems.

• Do not charge the battery for longer than the specified time!

If the battery pack has not finished charging even after the

regulated time has passed, stop it. The battery may generate heat

or smoke, rupture, or burst into flame.

• Do not place the battery pack into a microwave or high

pressure container!

The battery may generate heat or smoke, rupture, or burst into

flame.

• Keep ruptured and leaking battery packs away from fire!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from flammable areas. Electrolyte leaking

from battery can easily catch on fire and may cause the battery to

generate smoke or burst into flame.

• Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have different

coloring, is deformed, or seems abnormal for any other reason,

remove it from the charger or operating equipment and do not use

it. The battery may generate heat or smoke, rupture, or burst into

flame.

conTenTs

UNPACKING AND CHECKING EQUIPMENT.........................1

PREPARATION .........................................................2

ORIENTATION ..........................................................6

PROGRAMMABLE AUXILIARY FUNCTIONS........................7

BASIC OPERATIONS ..................................................9

VOICE OPERATED TRANSMISSION (VOX) ....................... 10

BACKGROUND OPERATIONS ...................................... 11

UNPACKING AND CHECKING EQUIPMENT

Carefully unpack the transceiver. If any of the items listed

below are missing or damaged, file a claim with the carrier

immediately.

SUPPLIED ACCESSORIES

• Antenna ..................................................................................1

• Battery charger/ AC adapter...................................................1

• TK-2302/ TK-3302: KSC-31

• TK-2302V/ TK-3302U: KSC-35

• Battery pack............................................................................1

• TK-2302/ TK-3302: KNB-29N (Ni-MH)

• TK-2302V/ TK-3302U: KNB-45L (Li-ion)

• Speaker/ microphone jack cover ............................................1

• Speaker/ microphone locking bracket ....................................1

• Belt clip (KBH-10)...................................................................1

• Screw set

• 3 x 6 mm (Black) ..................................................................... 1

• 3 x 8 mm ................................................................................. 2

• Instruction manual ..................................................................1

Note: Refer to "PREPARATION" for accessory installation

instructions.

Andere Handbücher für TK-2302

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kenwood Transceiver Handbücher

Kenwood

Kenwood TS-520S Bedienungsanleitung

Kenwood

Kenwood TS-930S Bedienungsanleitung

Kenwood

Kenwood TM-702A Bedienungsanleitung

Kenwood

Kenwood TM-621A Bedienungsanleitung

Kenwood

Kenwood TK-2118 Bedienungsanleitung

Kenwood

Kenwood Nexedge NX-5200 Bedienungsanleitung

Kenwood

Kenwood TK-3101K Bedienungsanleitung

Kenwood

Kenwood NX-320 Series Bedienungsanleitung

Kenwood

Kenwood TS-950SD Bedienungsanleitung

Kenwood

Kenwood TM-211A/E Bedienungsanleitung

Kenwood

Kenwood TM-D710E Bedienungsanleitung

Kenwood

Kenwood TH-27 Series Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3401D Bedienungsanleitung

Kenwood

Kenwood TS-811E Bedienungsanleitung

Kenwood

Kenwood TS-450S Bedienungsanleitung

Kenwood

Kenwood TK-7302 Bedienungsanleitung

Kenwood

Kenwood TK-3101 (UHF) Bedienungsanleitung

Kenwood

Kenwood TK-2200L Bedienungsanleitung

Kenwood

Kenwood TK-2140 Bedienungsanleitung

Kenwood

Kenwood ProTalk LT PKT-23LF Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Kenwood

Kenwood TS-790A Bedienungsanleitung

Kenwood

Kenwood TH-78A Bedienungsanleitung

Kenwood

Kenwood TH-79A Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung

Standard Horizon

Standard Horizon HX320E Bedienungsanleitung

Em-Trak

Em-Trak A100 Bedienungsanleitung

HPE

HPE Aruba QSFP28 Bedienungsanleitung