Kenwood TK-3406 Bedienungsanleitung

INSTRUCTION MANUAL

VHF FM TRANSCEIVER

TK-2406

UHF FM TRANSCEIVER

TK-3406

Thank You

We are grateful you have chosen KENWOOD for your land

mobile radio applications.

noTices To The user

◆Government law prohibits the operation of unlicensed radio

transmitters within the territories under government control.

◆Illegal operation is punishable by fine and/or imprisonment.

◆Refer service to qualified technicians only.

Safety: It is important that the operator is aware of, and

understands, hazards common to the operation of any

transceiver.

Firmware Copyrights

The title to and ownership of copyrights for firmware embedded in KENWOOD

product memories are reserved for JVC KENWOOD Corporation.

PrecauTions

• Do not charge the transceiver and battery pack when they are wet.

• Ensure that there are no metallic items located between the

transceiver and the battery pack.

• Do not use options not specified by KENWOOD.

• If the die-cast chassis or other transceiver part is damaged, do not

touch the damaged parts.

• If a headset or headphone is connected to the transceiver, reduce

the transceiver volume. Pay attention to the volume level when

turning the squelch off.

• Do not place the microphone cable around your neck while near

machinery that may catch the cable.

• Do not place the transceiver on unstable surfaces.

• Ensure that the end of the antenna does not touch your eyes.

• When the transceiver is used for transmission for many hours, the

radiator and chassis will become hot. Do not touch these locations

when replacing the battery pack.

• Do not immerse the transceiver in water.

• Always switch the transceiver power off before installing optional

accessories.

• The charger is the device that disconnects the unit from the AC

mains line. The AC plug should be readily accessible.

Turn the transceiver power off in the following locations:

• In explosive atmospheres (inflammable gas, dust particles, metallic

powders, grain powders, etc.).

• While taking on fuel or while parked at gasoline service stations.

• Near explosives or blasting sites.

• In aircrafts. (Any use of the transceiver must follow the instructions

and regulations provided by the airline crew.)

• Where restrictions or warnings are posted regarding the use of

radio devices, including but not limited to medical facilities.

• Near persons using pacemakers.

• Do not disassemble or modify the transceiver for any reason.

• Do not place the transceiver on or near airbag equipment while the

vehicle is running. When the airbag inflates, the transceiver may

be ejected and strike the driver or passengers.

• Do not transmit while touching the antenna terminal or if

any metallic parts are exposed from the antenna covering.

Transmitting at such a time may result in a high-frequency burn.

• If an abnormal odor or smoke is detected coming from the

transceiver, switch the transceiver power off immediately,

remove the battery pack from the transceiver, and contact your

KENWOOD dealer.

• Use of the transceiver while you are driving may be against traffic

laws. Please check and observe the vehicle regulations in your

area.

• Do not expose the transceiver to extremely hot or cold conditions.

• Do not carry the battery pack (or battery case) with metal objects,

as they may short the battery terminals.

• When operating the transceiver in areas where the air is dry, it is

easy to build up an electric charge (static electricity). When using

an earphone accessory in such conditions, it is possible for the

transceiver to send an electric shock through the earphone and to

your ear. We recommend you use only a speaker/microphone in

these conditions, to avoid electric shocks.

Information concerning the battery pack:

The battery pack includes flammable objects such as organic

solvent. Mishandling may cause the battery to rupture

producing flames or extreme heat, deteriorate, or cause other

forms of damage to the battery. Please observe the following

prohibitive matters.

• Do not disassemble or reconstruct battery!

The battery pack has a safety function and protection circuit to

avoid danger. If they suffer serious damage, the battery may

generate heat or smoke, rupture, or burst into flame.

• Do not short-circuit the battery!

Do not join the + and – terminals using any form of metal (such

as a paper clip or wire). Do not carry or store the battery pack in

containers holding metal objects (such as wires, chain-necklace or

hairpins). If the battery pack is short-circuited, excessive current will

flow and the battery may generate heat or smoke, rupture, or burst

into flame. It will also cause metal objects to heat up.

• Do not incinerate or apply heat to the battery!

If the insulator is melted, the gas release vent or safety function is

damaged, or the electrolyte is ignited, the battery may generate

heat or smoke, rupture, or burst into flame.

• Do not leave the battery near fire, stoves, or other heat

generators (areas reaching over 80°C/ 176°F)!

If the polymer separator is melted due to high temperature, an

internal short-circuit may occur in the individual cells and the

battery may generate heat or smoke, rupture, or burst into flame.

• Do not immerse the battery in water or get it wet by other

means!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke,

rupture, or burst into flame.

• Do not charge the battery near fire or under direct sunlight!

If the battery’s protection circuit is damaged, the battery may

charge at extreme current (or voltage) and an abnormal chemical

reaction may occur. The battery may generate heat or smoke,

rupture, or burst into flame.

iii

• Use only the specified charger and observe charging

requirements!

If the battery is charged in unspecified conditions (under high

temperature over the regulated value, excessive high voltage or

current over regulated value, or with a remodeled charger), it may

overcharge or an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not pierce the battery with any object, strike it with an

instrument, or step on it!

This may break or deform the battery, causing a short-circuit. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not jar or throw the battery!

An impact may cause the battery to leak, generate heat or smoke,

rupture, and/or burst into flame. If the battery’s protection circuit

is damaged, the battery may charge at an abnormal current (or

voltage), and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not use the battery pack if it is damaged in any way!

The battery may generate heat or smoke, rupture, or burst into

flame.

• Do not solder directly onto the battery!

If the insulator is melted or the gas release vent or safety function

is damaged, the battery may generate heat or smoke, rupture, or

burst into flame.

• Do not reverse the battery polarity (and terminals)!

When charging a reversed battery, an abnormal chemical reaction

may occur. In some cases, an unexpected large amount of current

may flow upon discharging. The battery may generate heat or

smoke, rupture, or burst into flame.

• Do not reverse-charge or reverse-connect the battery!

The battery pack has positive and negative poles. If the battery

pack does not smoothly connect with a charger or operating

equipment, do not force it; check the polarity of the battery. If the

battery pack is reverse-connected to the charger, it will be reverse-

charged and an abnormal chemical reaction may occur. The

battery may generate heat or smoke, rupture, or burst into flame.

• Do not touch a ruptured and leaking battery!

If the electrolyte liquid from the battery gets into your eyes, wash

your eyes with fresh water as soon as possible, without rubbing

your eyes. Go to the hospital immediately. If left untreated, it may

cause eye-problems.

• Do not charge the battery for longer than the specified time!

If the battery pack has not finished charging even after the

regulated time has passed, stop it. The battery may generate heat

or smoke, rupture, or burst into flame.

• Do not place the battery pack into a microwave or high

pressure container!

The battery may generate heat or smoke, rupture, or burst into

flame.

• Keep ruptured and leaking battery packs away from fire!

If the battery pack is leaking (or the battery emits a bad odor),

immediately remove it from flammable areas. Electrolyte leaking

from battery can easily catch on fire and may cause the battery to

generate smoke or burst into flame.

• Do not use an abnormal battery!

If the battery pack emits a bad odor, appears to have different

coloring, is deformed, or seems abnormal for any other reason,

remove it from the charger or operating equipment and do not use

it. The battery may generate heat or smoke, rupture, or burst into

flame.

CONTENTS

UNPACKING AND CHECKING EQUIPMENT.........................1

PREPARATION .........................................................2

ORIENTATION ..........................................................7

PROGRAMMABLE AUXILIARY FUNCTIONS........................8

BASIC OPERATIONS ................................................ 11

VOICE OPERATED TRANSMISSION (VOX) ....................... 12

BACKGROUND OPERATIONS ...................................... 13

UNPACKING AND CHECKING EQUIPMENT

Carefully unpack the transceiver. If any of the items listed

below are missing or damaged, file a claim with the carrier

immediately.

SUPPLIED ACCESSORIES

• Battery charger/ AC adapter (KSC-43)...................................1

• Ni-MH Battery pack (KNB-53N)..............................................1

• Speaker/ microphone jack cover ............................................1

• Speaker/ microphone locking bracket ....................................1

• Belt clip (KBH-10)...................................................................1

• Screw (M3 x 8 mm) ................................................................2

• Channel stopper .....................................................................1

• Instruction manual ..................................................................1

Note: Refer to "PREPARATION" for accessory installation

instructions.

PREPARATION

INSTALLING THE CHANNEL STOPPER

For transceivers with less than 16 channels, insert a Channel

stopper.

1 Set the Channel selector to channel 1, then pull the Channel

selector knob off the transceiver.

• If the Channel selector is not positioned at channel 1, the

Channel selector knob may not install correctly and the channel

may be unable to be changed.

2 Insert the channel stopper.

3 Set the arrow of the Channel stopper to the highest channel

number for the transceiver.

• You can set the Channel stopper position for channels 2, 4, 6,

8, 10, 12, and 14.

4 Reinsert the Channel selector knob.

Channel stopper

Arrow

INSTALLING THE (OPTIONAL) ANTENNA

Screw the antenna into the connector on

the top of the transceiver by holding the

antenna at its base and turning it clockwise

until secure.

Note: The antenna is neither a handle, a

key ring retainer, nor a speaker/ microphone

attachment point. Using the antenna in these

ways may damage the antenna and degrade

your transceiver’s performance.

Antenna

INSTALLING/ REMOVING THE BATTERY PACK

◆Do not short the battery terminals or dispose of the battery by fire.

◆Never attempt to remove the casing from the battery pack.

1Align the battery pack with the back

of the transceiver, then press the

battery pack and transceiver firmly

together until the release latch on

the base of the transceiver locks.

2To remove the battery pack, lift

the safety catch on the base of the

transceiver, then press the release

latch underneath the safety catch.

3While pressing the release latch,

pull the battery pack away from the

transceiver.

INSTALLING THE BELT CLIP

Do not use glue which is designed to prevent screw loosening when

installing the belt clip, as it may cause damage to the transceiver. Acrylic

ester, which is contained in these glues, may crack the transceiver’s

back panel.

Belt clip

If necessary, attach the belt clip using

the two supplied M3 x 8 mm screws.

Note: If the belt clip is not installed, its

mounting location may get hot during

continuous transmission or when left

sitting in a hot environment.

CHARGING THE BATTERY PACK

The battery pack is not charged at the factory; charge it before

use.

ATTENTION: Always switch OFF a transceiver equipped with a

battery pack before inserting the transceiver into the charger.

1Plug the AC adapter cable into the jack located on the rear

of the charger.

2Plug the AC adapter into an AC outlet.

3Match the Holder to the type of battery pack to be charged

so that when inserting the Holder, the battery type name

can be seen on the bottom of the charger. After inserting the

Holder into the charger, press the locking tabs to secure it in

place.

Holder

Li-ion battery

charger

Ni-MH battery

charger

• To remove the Holder, squeeze the locking tabs together then

pull the Holder out of the charger.

4Slide a battery pack or a transceiver equipped with a battery

pack into the charging slot of the charger.

• Make sure the metal contacts of the battery pack mate securely

with the charger terminals.

• The indicator lights red and charging begins.

Indicator

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kenwood Transceiver Handbücher

Kenwood

Kenwood TK-7180 Montage- und Bedienungsanleitung

Kenwood

Kenwood TS-711A Bedienungsanleitung

Kenwood

Kenwood TK-3601D-E Bedienungsanleitung

Kenwood

Kenwood TS-660 Bedienungsanleitung

Kenwood

Kenwood TR-751A Bedienungsanleitung

Kenwood

Kenwood 144MHz FM TRANSCEIVER K2E Bedienungsanleitung

Kenwood

Kenwood TK-5210 Bedienungsanleitung

Kenwood

Kenwood TM-255A Bedienungsanleitung

Kenwood

Kenwood TK-2400 Bedienungsanleitung

Kenwood

Kenwood TM-3530A Bedienungsanleitung

Kenwood

Kenwood TS-700G Bedienungsanleitung

Kenwood

Kenwood TK-5410 Bedienungsanleitung

Kenwood

Kenwood TK-D340 Bedienungsanleitung

Kenwood

Kenwood TS-711A/E Bedienungsanleitung

Kenwood

Kenwood TK-7150 Bedienungsanleitung

Kenwood

Kenwood UBZ-LJ8 Bedienungsanleitung

Kenwood

Kenwood UBZ-LF14 Bedienungsanleitung

Kenwood

Kenwood FleetSync TK-5810(H) Bedienungsanleitung

Kenwood

Kenwood Nexedge NX-5200 Bedienungsanleitung

Kenwood

Kenwood TK-3160 Bedienungsanleitung

Kenwood

Kenwood TM-255A/E Bedienungsanleitung

Kenwood

Kenwood TM-731A Bedienungsanleitung

Kenwood

Kenwood NX-5700 Bedienungsanleitung

Kenwood

Kenwood TK-3312 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung

Standard Horizon

Standard Horizon HX320E Bedienungsanleitung

Em-Trak

Em-Trak A100 Bedienungsanleitung

HPE

HPE Aruba QSFP28 Bedienungsanleitung