Key Digital KD-4x8CS Champion Bedienungsanleitung

HDMI Matrix Switchers

The Experts in Digital Video Technology and Solutions™

KD-4x8CS / KD-6x6CS

KD-4x8CS

KD-6x6CS

KD-8x4CS

KD-8x8CS

KD-8x4CS / KD-8x8CS

Setup Guide

Table of Contents

About KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS .............................. 1

Connections, Buttons and LEDs ................................................ 2

Application Example ......................................................... 3

Quick Setup Guide: .......................................................... 3

Settings................................................................... 4

Remote Control ............................................................. 4

RS-232 Commands ......................................................... 5

Specications .............................................................. 7

Important Product Warnings & Safety Instructions ................................... 8

How to Contact Key Digital

................................................... 9

Warranty Information ......................................................... 9

About KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS

Description

›Key Digital

Champion Series

™

HDMI Matrix Switchers are designed and engineered to offer the

best in quality, performance, and reliability, while providing cost effective HDMI matrixing solutions.

KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS enable any HDMI Source to be viewed on any

HDMI Output/Display at any time and in any combination. KD-4x8CS, KD-6x6CS, KD-8x4CS &

KD-8x8CS maintain crystal-clear, pristine picture and sound quality, while supporting all HD

and

SD video standards, including 1080p/60 and 3D, and is switchable via pushbutton, IR,

and RS-232 control.

Key Features

›Internal EDID Library features 12 default EDID congurations, in addition to native EDID data for

any Output/Display

›Supports all SD, HD, and VESA resolutions up to 1080p (60Hz & 50Hz)

»SD & HD: 480i, 480p, 720p, 1080i, 1080p

»VESA / VGA (RGBHV): From 640x480p up to 1920x1200p

›Advanced HDMI

Feature: 3D Ready

›Full support for 12-bit Deep Color and HDCP

›Supports lossless compressed digital audio:

»Dolby

TrueHD, Dolby

Digital Plus and DTS

™

-HD Master Audio

Key Benets

›Key Digital’s Buffered Matrix Technology

™

allows up to 4/6/8 HDMI sources to be independently

switched to 4/6/8 Displays or Zones at any time and in any combination

›LED Link Lights indicate connectivity between KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS

and each input & output device

›Serial IR, Optical IR, Front Panel & RS-232 control

›Supports major control systems such as Compass Control

, AMX

, Control4

, Crestron

RTI

, Universal

›Rack Mountable (1U) with included rack ears

Accessories

›(1) External 12 Volt 5 Amp power supply (110V-240V 50/60Hz)

›(1) IR Remote Control

›(1 pair) Rack mounting ears

›HDMI Clips

›Setup Guide

›Warranty Card

Rack Mounting:

›Secure the rack ears to each side of the KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS with

the supplied hardware. Then, fasten the unit to the rack rails with the included machine screws.

Slide Clip on

to Screw

Loosen Screw

Secure Screw

Insert Key Digital®

HDMI® Cable

Fasten HDMI Cable to Clip

with Cable Tie

Connections, Buttons and LEDs

Rear Panel Connections:

All connections to the KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS are found on the rear

panel of the units. Refer to the illustrations below for port assignments while making connections.

Power

Serial IR

IR Eye

Operation Mode

RS-232 Port

HDMI Inputs & LEDs HDMI Outputs & LEDs

Connections

›HDMI Inputs: The HDMI Inputs are located on the left side of the back panel. The Inputs have a

blue LED that will illuminate when a source is connected and synced.

›HDMI Outputs: The HDMI Outputs are located on the right side of the back panel. The Outputs

have a blue LED that will illuminate when a output device is connected and synced.

›The RS-232, Serial IR, Optical IR Sensor, Operation Mode Switch and Power connections

are located on the right side of the back panel.

›The Operation Mode switch is used to update the unit’s

rmware, which is done using the DB9/RS-232 port. The

rmware version as well as all RS-232 commands is available

through the RS-232 command ‘H’. A detailed list of RS-232

commands is available later in this guide.

›If newer rmware is made available, complete updating

instructions will be included with it. Check the Key Digital

website for any rmware updates.

Front Panel Buttons and LEDs

Output Select Buttons

IR Eye

Input LEDs

›There are 4/6/8 Output buttons along the front panel.

›Pressing an output button will select the next HDMI input.

›A blue LED will indicate which Input has been selected for each Output.

›There is also an Optical IR window located on the right side of the front panel for IR remote

control signals.

Application Example

HDMI

Blu-Ray Cable Box Satellite Box Apple TV

DVD Player (HD)

Playstation 3

HDMI

Display 1 Display 2 Display 3 Display 4 Display 5 Display 6

HDMI

KD-6x6CS

RS232 Control

Serial IR

Optical IR

KD-MC2500

Master Controller

IR/RS-232

Quick Setup Guide:

1. Begin with the KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS and all input/output devices

turned off and power cables removed.

2. Connect HDMI sources to the appropriate input ports on the KD-4x8CS, KD-6x6CS,

KD-8x4CS & KD-8x8CS.

3. Connect HDMI outputs to the appropriate output device (display, projector, AV Receiver, etc).

4. Connect power to the KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS and all other input

and output devices and turn them on.

5. Operate the KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS switcher via front panel buttons,

IR Remote, Serial IR or RS-232 control.

Operation:

After performing the setup above, the unit is ready for operation.

There are several options for controlling the unit. Commands can be issued via IR remote control,

RS-232 or by using the front panel buttons. Note that the advanced commands are available only

via the RS-232 protocol.

Settings

The KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS features a library of 12 internal EDID

(Extended Display Identication Data) les, in addition to allowing any Input source to receive

a copy of the EDID information of any selected Output connected via HDMI. The default EDID

setting is “04” – 1080p 2ch Digital Audio. Changing to EDID settings may be necessary when

connecting to or from an AV Receiver, or for passing 3D content derived from a Cable or Satellite

source if the default EDID has problems.

They can also speed up the switching process with cable or satellite sources.

The possible EDID settings can range from ‘01’ to ‘12’. (‘04’ is the default).

01 1080i, 2CH Audio 07 3D, 1080p 2CH Audio

02 1080i, DOLBY/DTS 5.1 08 3D, DOLBY/DTS 5.1

03 1080i, HD Audio 09 3D, HD Audio

04 1080p, 2CH Audio 10 1280x1024 DVI

05 1080p, DOLBY/DTS 5.1 11 1920x1080 DVI

06 1080p, HD Audio 12 1920x1200 DVI

When selecting an EDID from the library (settings 01-12),

your source device will see the KD-4x8CS, KD-6x6CS, KD-

8x4CS & KD-8x8CS EDID choice instead of the display’s

EDID, overriding the display’s own EDID information.

If your display is not capable of accepting the video

resolution or audio type selected, you may not see a picture

or hear sound. In this case please choose another more

compatible EDID, or use the default EDID.

EDID settings can only be changed through the RS-232

command protocol. See the RS-232 command section

below for a list of EDID commands available.

Remote Control

You may switch inputs on the KD-4x8CS, KD-6x6CS,

KD-8x4CS & KD-8x8CS by using the supplied IR Remote

control. There are 2 groups of controls, one group for outputs

and one group for inputs. To execute a switching command,

rst select the output you wish to switch (1), then select the

desired input (2).

Models for this Remote Front

Back

Front

Back

Remote Buttons:

PMS Cool Gray 11U

PVC Inlay:

PMS Black

Silkscreen:

White

Body:

Black

Power Button:

PT 355 U

Sasha 11.13.2012 – Remote SKU: KDRM8XNCS

KD4X8CS

KD8X4CS

KD6X6CS

KD8X8CS

KDRM8XNCS

Part Number:

Power

www.keydigital.com

1 2 3 4

Input Select

1 2 3 4

5 6 7 8

Output Select

KDRM8XNCS

Part Number:

Power

www.keydigital.com

1 2 3 4

Input Select

1 2 3 4

5 6 7 8

Output Select

Output

Select

Input

Select

IR Extender:

You may want to use an IR extender, such as the KD-IRKIT300. Front and Rear panel sensors are

available for use with the IR extender. A wired IR serial connector is also provided at the rear of the

unit. Wired IR Extender KD-IRB3099 in the KD-IRKIT300 uses a 3.5mm male-to-male Mono cable.

(Not Included with KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS)

Connecting Block

KD-IRCB204

KD-IRB3099

Back of the Unit

Wired IR Extender

3.5mm male-to-male

mono cable

RS-232 Commands

The KD-4x8CS, KD-6x6CS, KD-8x4CS & KD-8x8CS provide access to all functions when used

with an RS-232 control system.

The connection protocol is as follows:

»Baud rate: 57,600

»Data Bits: 8

»Parity: None

»Stop Bits: 1

»Flow Control: None

»Carriage Return: Required

»Line Feed: Required

Pin 5 – Ground

Pin 3 – Receive

Pin 2 – Transmit

RS-232 cable pin out

NOTE: All commands are case-insensitive. Spaces are shown for clarity; commands should not

have any spaces. Every command below requires a carriage return at the end of the string for the

command to be executed. If a new line character is received, a prompt should be sent back.

System Commands:

›H: Help - Help command. List of all RS-232 commands and Firmware version.

›STA: Status Command - Displays unit status for all internal variables such as Video Input, and

EDID selected for each Input.

›PF: Power Off - Power Off command

›PN: Power ON - Power ON command

Commands:

Video Switch:

»‘SP O xx SI yy’ To switch the desired Video Input to the desired Output:

»xx = the Output number [01-04/06/08] –OR- [A] for ‘All’

»yy = the Input number [01-04/06/08] –OR- [U, D] for ‘Up’,’ Down’ respectively.

»‘U/D’ will increase/decrease the input number from its current position.

»This command will switch Inputs to your desired Output.

»Example: To switch Output 3 to Input 1, issue the command; ‘SPO01SI03’

»Example: To incrementally switch the Input Up from its present number for Output 1, issue

the command: ‘SPO01SIU’

»Example: To switch All Outputs to Input 3, issue the command: ‘SPOASI03’

EDID Copy and Default EDID Library:

»‘SP C EDID xx H/D yy’: To Copy EDID to Input from HDMI Output, or from a Default Library

»xx = Input numbers [01-04/06/08] –OR- [A] for ‘All’ Inputs

»H = EDID Copy from HDMI Output

»D = Default EDID Library selection (see list below)

»yy = Output numbers [01-04/06/08] when ‘H’ variable is selected

–OR-

Default EDID library settings [01-12] when ‘D’ variable is selected.

»This command will either copy the EDID information from a selected Output to a specic

Input (or All Inputs), or, write EDID information from an internal library of default EDID settings

to a specic Input (or All Inputs).

»Example: To copy the EDID information from HDMI Output 2 to Input 4, issue the command:

‘SPCEDID04H02’

»Example: To write the EDID information from the built-in default EDID library using default

EDID 1 to Input 2, issue the command; ‘SPCEDID02D01’

»The possible EDID settings can range from ‘01’ to ‘12’. (‘04’ is the default).

01 1080i, 2CH Audio 07 3D, 1080p 2CH Audio

02 1080i, DOLBY/DTS 5.1 08 3D, DOLBY/DTS 5.1

03 1080i, HD Audio 09 3D, HD Audio

04 1080p, 2CH Audio 10 1280x1024 DVI

05 1080p, DOLBY/DTS 5.1 11 1920x1080 DVI

06 1080p, HD Audio 12 1920x1200 DVI

Front Panel Buttons Enabled/Disabled:

»‘SP C FB E/D’

»Where ‘E’ will Enable the front panel buttons and ‘D’ will Disable the front panel buttons.

»Example: To Disable the front panel buttons, issue the command; ‘SPCFBD’

Reset to Factory Defaults:

»‘SP C DF xx’

»xx = [01-12] and is the default EDID library loaded during a factory reset.

»This command will return the unit to its factory default settings including a user chosen

default EDID setting. (See above for a list of possible default EDID library settings available)

»Example: To reset the unit to factory default with an EDID setting of 1080i 2CH Audio, issue

the command; ‘SPCDF01’

»Example: To reset the unit to factory default with an EDID setting of 3D 1080p 2CH Audio,

issue the command; ‘SPCDF07’

Operation Mode/Firmware Upgrade Procedure

There is an Operation Mode dial located on the rear right of the unit.

›Position 1 is the normal operation mode position. The dial must be in this position

for the unit to function.

›Positions 2, 3 & 4 are used for upgrading the unit’s rmware. To upgrade your

unit’s rmware, follow the below procedure:

»Open the KD Flash2 software on your Windows computer

1. Ensure the Rotary Switch Position menu

within the KD Flash2 software is selecting

Position 2:

2. Set the Operation Mode dial on the rear of

your matrix to Position 2:

3. Press “Select File” in the KD Flash2

software and select the appropriate

rmware le:

4. Press “Upgrade”

»Repeat the above procedure for positions 3 and 4. Be sure the Rotary Switch Position menu

in the KD Flash2 software is selecting the appropriate position for the Operation Mode dial

on the rear of your matrix.

Speciﬁcations

Technical:

»Input (Each): 1 HDMI Connector, Type A, 19 Pin Female

»Output (Each): 1 HDMI Connector, Type A, 19 Pin Female

»Bandwidth: TMDS bandwidth 10.2 Gb/s

»Control: Front panel push buttons and LEDs; IR sensor front/rear; RS-232 Tx/Rx lines with

full bi-directional operation

»Video/Audio Matrix Switching: Full matrix switching for HDMI Video & Audio, DVI Video

»Deep Color Support: Supports digital video formats in Deep Color Mode up to

12 bits/color with all HDMI and HDCP technologies

»HDMI

and HDCP Licensing: Fully licensed and compatible with all HDMI

and HDCP technologies

»Link: Single Link

»EDID Control: EDID information is assigned to the inputs from the internal EDID library or

from a display’s internal EDID data

»Lossless Compressed Digital Audio: Supports lossless compressed digital audio:

Dolby

TrueHD, Dolby

Digital Plus and DTS

™

-HD Master Audio

»DDC Signal (Data): Input DDC Signal - 5 Volts p-p (TTL)

»HDMI Video/Audio Signal: Input Video Signal - 1.2 Volts p-p

»DDC Communication: EDID and HDCP Bi-directional Transparency from Display to Source

»Wired IR: modulated IR signal input, 0-5V TTL or -10to +10V.

»Power: External Power Supply. 12V/5A

General:

»Regulation: CE, RoHS, WEEE

»Rack Mount: 1U, Full Rack Width (rack ears included)

»Enclosure: Black Metal

»Product Dimensions: 17.13” x 6.63” x 1.71”

»Shipping Dimensions: 23.1” x 9.45” x 3.8”

»Product Weight: 4.05 lb.

»Shipping Weight: 6 lb

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Key Digital Matrix-Umschalter Handbücher

Key Digital

Key Digital FatBOY KD-MSA8X8 Bedienungsanleitung

Key Digital

Key Digital KD-UPS52U Bedienungsanleitung

Key Digital

Key Digital KD-MSWCAT4x4 FatBOY Bedienungsanleitung

Key Digital

Key Digital KD-MSWCAT8x8 FatBOY Montage- und Bedienungsanleitung

Key Digital

Key Digital KD-MSW4X2 Bedienungsanleitung

Key Digital

Key Digital KD-MSW 8x3 Bedienungsanleitung

Key Digital

Key Digital KD-MAX8x8 Bedienungsanleitung

Key Digital

Key Digital KD-MSVA4X4 FatBOY Bedienungsanleitung

Key Digital

Key Digital KD-MS4x4G Bedienungsanleitung

Key Digital

Key Digital KD-HDMS8X8 Bedienungsanleitung

Key Digital

Key Digital KD-MSW8X4 Bedienungsanleitung

Key Digital

Key Digital KD-MSW8X4 Bedienungsanleitung

Key Digital

Key Digital Champion KD-4X4XC Bedienungsanleitung

Key Digital

Key Digital KD-2X2CS Champion Bedienungsanleitung

Key Digital

Key Digital FatBOY KD-MSA8X8 Bedienungsanleitung

Key Digital

Key Digital Digital IQ Series Bedienungsanleitung

Key Digital

Key Digital KD-HD16x16ProK Bedienungsanleitung

Key Digital

Key Digital Flash Matrix KD-MSW8x3 Bedienungsanleitung

Key Digital

Key Digital KD-Pro8x8D Bedienungsanleitung

Key Digital

Key Digital KD-HDMS4X4 Hercules Bedienungsanleitung

Key Digital

Key Digital Phantom KD-HDMSW4X4 Bedienungsanleitung

Key Digital

Key Digital KD-MSVA4X4Pro Bedienungsanleitung

Key Digital

Key Digital KD-HD4x4 Bedienungsanleitung

Key Digital

Key Digital KD-CATRCAAA Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte