Key Digital KD-MSWCAT8x8 FatBOY Montage- und Bedienungsanleitung

KD-MSWCAT8X8 KD-VACRX

KD-MSWCAT4X4 KD-CVARX

Addendum

This addendum describes additional features of Key Digital®FatBoy Series™

KD-MSWCAT8X8 and KD-MSWCAT4X4 spotlighting integration with KD-VACRX

and KD-CVARX Receiver Baluns.

KD-MSWCAT8x8

KD-MSWCAT4x4

Component/VGA with Audio via CAT5 Matrix Switchers

Page 2

The following new features have been added to both

the KD-MSWCAT8x8 and KD-MSWCAT4x4 products:

Key Features

»Allows the use of either KD-VACRX or KD-CVARX receive Baluns

»KD-CVARX can be used with a Digital or Analog Audio Input (Analog Output only)

»Can now route IR signals when in Component mode via unused “H” (Horizontal sync)

signal path

Key Beneﬁts

»Can mix both KD-VACRX and KD-CVARX Baluns on single unit

»Control display or other local (room) components by sending IR through KD-VACRX and

KD-CVARX Baluns

»Allows use of KD-CVARX Baluns when Digital Audio and RS232 Output isn’t required

Additional Key Features

»Front panel LED input/output assignment conﬁrmation

»Easily controlled via IR Remote (included) with discrete codes, Serial IR, and RS-232

»Slim 1U Rack chassis for space conservation

RS232 Commands:

The following new RS232 commands have been added to provide control for the new features:

½‘SPCVTx’ - Video Type command: where x = 0 or 1 (0 = Component, 1 = RGBHV)

»Note: default is component.

»This command determines whether unit will switch Component or RGBHV signals.

»Example: To switch the unit from Component to RGBHV mode, enter the command;

‘SPCVT1’

»(Please note that a system reboot is required after a ‘Video Type’ switch for the settings to

take effect)

½‘SPOxxSRyy’ – IR Switching command: where xx = Output number, yy = Input number.

»This command directs the IR path from your chosen input to your chosen output

independent of your A/V routing.

»Example: to direct the IR path from input 4 to output 2, issue the command: ‘SPO02SR04’

»NOTE: for expansion conﬁgurations, total number of inputs will be limited to 8

(or 4 for KD-MSWCAT4x4

»The default assignments for IR routing are Input 1 to Output 1, Input 2 to Output 2 etc.

½‘SP C C5T hh’ - CAT5 Output Type Mask: where hh = hex value for selecting which outputs will

have KD-VACRX Balun and which will have KD-CVARX Baluns (0-VAC, 1-CVA) ‘0’ is the default

setting

»This command tells the unit which type of Balun is connected to each output number. A

selected output will choose the KD-CVARX Balun; an unselected output chooses the KD-

VACRX Balun (default).

Page 1

»See the hex value/binary number conversion table to generate the proper number to enter

for this value.(pg. 4)

»The status display through RS-232 has been updated to reﬂect the changes.

»Output:

»01 : Video= 01, Audio= 01, IR= 01 : Active : Mute Interval= 00

Balun= VAC : V= 50 B= 20 L= 12 M= 12 T= 12 LP= 00

»02 : Video= 02, Audio= 02, IR= 02 : Active : Mute Interval= 00

Balun= VAC : V= 50 B= 20 L= 12 M= 12 T= 12 LP= 00

Pin out for using KD-CVARX Baluns with KD-MSWCAT8X8 / 4X4

Please note that to utilize the KD-CVARX Baluns you will need to terminate your CAT5 cabling

using the following pin out:

1 1

2 2

3 3

4 4

5 5

6 6

7 7

8 8

KD-MSWCAT8X8 / 4X4 KD-CVARX

Analog Audio

Balanced Audio

Left

Right

Gnd

Gnd Left + Right+

Gnd Gnd

+ – + –

Tip

Ring

Sleeve

Digital Audio

Gnd

PCM

Gnd +

Gnd

R-

L-

Gnd

R+

L+

Right

IR routing through KD-MSWCAT8X8 / 4X4:

In order to send IR signals through the KD-MSWCAT8X8/4X4, you will need to follow the

conﬁguration described below.

½To input IR signals, you will need to convert your powered IR distributions

output to an RCA type connector. Typically you can use a mono 3.5mm jack

to RCA adapter (as shown).

½Using a standard RCA male to male cable, connect this RCA to the unused ‘H’ or Horizontal

Sync input going into the switch. The supplied breakout cable is used for Component signals

and has 3 RCA connections. You will need a 5 RCA to VGA (Part number KD-VACBL not

included) breakout connector for both Switch and Balun. (Total of 2 per signal, see complete

parts list below).

½NOTE: When using the KD-CVARX Baluns, you will need to supply a female

to female HD15 gender changer to connect the Balun to the breakout cable

(KD-VACBL) this changer is not needed for the KD-VACRX Baluns.

½At the Balun side, plug an RCA to 3.5mm female mono jack adapter into the

unused ‘H’ or Horizontal output coming off the HD15 to 5 RCA breakout cable from the Balun.

You may plug your emitter directly into this adapter which can then be placed onto your display

or any other device you wish to control. You may repeat this for each IR signal you wish to route

through the KD-MSWCAT8X8/4X4.

Page 2

Here is a complete list of all items required to send IR through the KD-MSWCAT8X8/4X4.

(Items listed are for a single connection).

Product Qty. Description Use

13.5mm male mono

jack to RCA female

adapter

Converts IR Distribution output to

RCA to connect to Baluns

2KD-VACBL 5 RCA

breakout cable

Breaks out 15 pin to 5 separate

female RCA connections

1Single male RCA to

male RCA

Carries IR signal to input of

breakout cable

1RCA male to 3.5mm

mono female adapter

Converts IR output of Balun to

allow standard emitter to plug in

115 pin VGA female to

female adapter

If using KD-CVARX Baluns for 5

RCA breakout cable to ﬁt

1Standard IR emitter To send IR to device you wish to

control

Audio Connections

The KD-MSWCAT4x4 / 8x8 has Two (2) 3.5mm audio input connections for each video input. For

standard Analog Stereo sources, utilize the left input. For Digital PCM sources utilize the right input.

For Balanced Analog sources, utilize both inputs. Pin outs for these connections are shown below.

Page 3

Standard Analog Stereo connections:

This is the standard unbalanced audio pin out. This signal will be available when using either KD-

VACRX or KD-CVARX Balun.

1 1

2 2

3 3

4 4

5 5

6 6

7 7

8 8

KD-MSWCAT8X8 / 4X4 KD-CVARX

Analog Audio

Balanced Audio

Left

Right

Gnd

Gnd Left + Right +

Gnd Gnd

+ – + –

Tip

Ring

Sleeve

Digital Audio

Gnd

PCM

Gnd +

Gnd

R-

L-

Gnd

R+

L+

Right

Balanced Analog Audio connections:

Normally an unbalanced audio connection is utilized for standard source equipment. If you wish to

use a balanced signal., the KD-MSWCAT8x8 has two (2) 3.5mm stereo audio input jacks for each

video input and is capable of transmitting a balanced signal across the 2 audio inputs by wiring

each connection as shown:. Note that the balanced audio signal will only be available when using

the KD-VACRX Baluns.

1 1

2 2

3 3

4 4

5 5

6 6

7 7

8 8

KD-MSWCAT8X8 / 4X4 KD-CVARX

Analog Audio

Balanced Audio

Left

Right

Gnd

Gnd Left + Right +

Gnd Gnd

+ – + –

Tip

Ring

Sleeve

Digital Audio

Gnd

PCM

Gnd +

Gnd

R-

L-

Gnd

R+

L+

Right

Page 4

Digital Audio connections:

This is the pin out for the LPCM Digital Audio connection. Note that the Digital audio signal will only

be available when using the KD-VACRX Baluns.

1 1

2 2

3 3

4 4

5 5

6 6

7 7

8 8

KD-MSWCAT8X8 / 4X4 KD-CVARX

Analog Audio

Balanced Audio

Left

Right

Gnd

Gnd Left + Right +

Gnd Gnd

+ – + –

Tip

Ring

Sleeve

Digital Audio

Gnd

PCM

Gnd +

Gnd

R-

L-

Gnd

R+

L+

Right

Binary to Hex:

The following diagrams illustrate how these values correspond to each unit, and how each hex

value represents which Output number is selected per unit. The characters that will be entered

into each ‘h’ can range between 0 – 9 plus A - F. Each character (0 – F) has a binary value that will

determine which outputs will receive the command:

8 - 5 4 - 1

0 0 0 0 0 0 0 0

8 7 6 5 4 3 2 1

O u t p u t s

0 0 0 0

4 3 2 1

Where 1 = Selected Where 0 = Unselected

0 0 0 1 = Output 1

0 0 0 0

4 3 2 1

0 1 0 0 = Output 3

(h = 1)

(h = 4)

0 0 0 0

4 3 2 1

1 0 0 1 = Output 1 & 4

(h = 9)

0 0 0 0

8 7 6 5

1 0 1 1 = Output 5, 6 & 8 (h =B)

Binary Value

Hex Value

Example of BINARY to HEX Conversion

0 = 0000

1 = 0001

2 = 0010

3 = 0011

4 = 0100

5 = 0101

6 = 0110

7 = 0111

8 = 1000

9 = 1001

A = 1010

B = 1011

C = 1100

D = 1101

E = 1110

F = 1111

BINARY to HEX Conversion chart

Hex Value Binary Value

Page 5

IR Distribution with KD-MSWCAT8X8/4X4 & KD-CVARX Baluns

CAT5/6/7 run 1000’

IR Distribution

RCA to Emitter

Connecting Block

KD-MSWCAT8X8

KD-VACBL

KD-IRCB204

KD-CVARX

521 East 3rd Street, Mount Vernon, NY 10553

Phone :: 914.667.9700 Fax :: 914.668.8666

Web :: www.keydigital.com

Key Digital

, led by digital video pioneer Mike Tsinberg,

develops and manufactures high quality, cutting-edge

technology solutions for virtually all applications where

high quality video imaging is important. Key Digital

is at the forefront of the video industry for Home

Theater Retailers, Custom Installers, System Integrators,

Broadcasters, Manufacturers, and Consumers. We

provide

total video system solutions because we

know and help drive the technology, the industry, the

business, and all the latest up-and-coming standards.

But most of all, we know exactly what you need for your

unique application - the right solution.

Rev 0 – Aug. 2010

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Key Digital Matrix-Umschalter Handbücher

Key Digital

Key Digital KD-HDMS1X15 Bedienungsanleitung

Key Digital

Key Digital KD-MSW8X4 Bedienungsanleitung

Key Digital

Key Digital KD-MAX8x8 Bedienungsanleitung

Key Digital

Key Digital KD-MS8x8G-2 Bedienungsanleitung

Key Digital

Key Digital KD-MS4x4G Bedienungsanleitung

Key Digital

Key Digital Champion KD-4X4XC Bedienungsanleitung

Key Digital

Key Digital KD-HD4x4 Bedienungsanleitung

Key Digital

Key Digital KD-4x2CS Champion Bedienungsanleitung

Key Digital

Key Digital Champion KD-16x16CS Bedienungsanleitung

Key Digital

Key Digital Champion KD-4X4 Bedienungsanleitung

Key Digital

Key Digital KD-VW4x4Pro Bedienungsanleitung

Key Digital

Key Digital Digital IQ Series Bedienungsanleitung

Key Digital

Key Digital KD-MSVA4X4 FatBOY Bedienungsanleitung

Key Digital

Key Digital KD-Pro6x6CC Bedienungsanleitung

Key Digital

Key Digital KD-4x4CSA Bedienungsanleitung

Key Digital

Key Digital Phantom KD-HDMSW4X4 Bedienungsanleitung

Key Digital

Key Digital KD-MS4x4G Bedienungsanleitung

Key Digital

Key Digital KD-MSWCAT4x4 FatBOY Bedienungsanleitung

Key Digital

Key Digital KD-MSV8X8 Bedienungsanleitung

Key Digital

Key Digital KD-VW4x4ProK Bedienungsanleitung

Key Digital

Key Digital KD-MSW8X4 Bedienungsanleitung

Key Digital

Key Digital KD-CATRCAAA Bedienungsanleitung

Key Digital

Key Digital KD-4x4CSK Bedienungsanleitung

Key Digital

Key Digital KD-MSW4x2Pro Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte