Key Digital KD-HDMS1X15 Bedienungsanleitung

Key Digital

Hercules Series

™

KD-HDMS8x8 is a HDMI Matrix Switcher capable of switching

up to 8 HDMI/DVI Video Sources/Inputs to 8 independent Zones/Outputs via HDMI and CAT5.

Features card slot architecture providing ﬂexible Input/Output conﬁgurations.

KD-HDMS8X8

8 Inputs to 8 Outputs HDMI Matrix Switcher

Also Available in Conﬁgurable Models Below:

KD-HDMS1X15, 2X14, 3X13, 4X12, 5X11, 6X10, 7X9

KD-HDMS15X1, 14X2, 13X3, 12X4, 11X5, 10X6, 9X7

Set Up Guide

Page 2

Table of Contents

About KD-HDMS8X8......................................................... 2

Connections, LCD and Button Map .............................................. 3

Application Example ......................................................... 5

Quick Setup Guide .......................................................... 6

IR Remote Command List .....................................................12

RS-232 Control Codes .......................................................12

Speciﬁcations ..............................................................16

Important Product Warnings & Safety Instructions ...................................18

How to Contact Key Digital

....................................................19

Warranty Information .........................................................19

About KD-HDMS8X8

Description

»HDMI Matrix Switcher capable of switching up to 8 HDMI/DVI Video Sources/Inputs to 8

independent Zones/Outputs via HDMI and CAT5. Custom conﬁgurable to 1x15, 2x14, 3x13,

4x12, 5x11, 6x10, 7x9, 9x7, 10x6, 11x5, 12x4, 13x3, 14x2 and15x1 combinations.

Key Features

»Full switching of 3 independent matrixes: Video, Audio and Control

»Supports all SD, HD, and VESA (VGA, SVGA, XGA, WXGA, SXGA, UXGA) resolutions

up to 1080p (60Hz & 50Hz)

»SD & HD: 480i, 480p, 720p, 1080i, 1080p

»VESA / VGA (RGBHV): From 640x480p up to 1920x1200p

»Full support for HDMI

1.3a/b with HDCP, 3D Ready, 4K Resolution Support

»Supports lossless compressed digital audio (Dolby

TrueHD, Dolby

Digital Plus

and DTS

™

-HD Master Audio)

»Internal EDID Library features 8 default EDID conﬁgurations in addition to native

EDID data from any Output/Display

Key Beneﬁts

»Transmits 1080p/60Hz resolution up to 140 ft, 1080p/24, 1080i, 720p and 480i/p resolutions

up to 270 ft, when used with KD-BBRX receiver Baluns

»Video, Audio, IR and RS-232 distribution via a single CAT5 cable

»Fully automatic CAT5 cable equalization, with optional manual calibration

»16 active outputs (8 HDMI/DVI and 8 CAT5) enables ﬂexible integration

»Full Audio control per output for volume, treble, bass, balance, and lip-sync from analog or

2ch. PCM HDMI digital sources

Page 3

Connections, LEDs and Button Map

Front Panel

Main Control Panel

Please see p. 4 for

detailed description

Input Cards 1-8 (KD-HDUIC)

Please see p. 4 for

detailed description

Looking at the rear panel, card slots are numbered from left to right

Output Cards 1-8 (KD-HDUOC)

Please see p. 4 for

detailed description

LCD Screen

Displays Menu selections, Input and

Output information, system settings and

status information

Right Selector

Use to access sub-menus

within the Main Menu.

(see pg.8 for complete

operating instructions)

Left Selector

Use to access Main Menu

and select sub-menu choices.

(see pg.7 for complete

operating instructions) IR Eye

Rear Panel

»Serial IR, Optical IR, Front Panel Control, Discrete Remote Codes, RS-232 and TCP/IP.

Supports major control systems such as AMX

, Colorado vNet

, Control4

, Crestron

, RTI

Savant, Universal

, Xantech

Accessories

»External +12V/8.33A (100W) Power Supply – KD-PS12V8A

»IR Remote control with two batteries

»Operating Instructions

»HDMI Cable Clips (16)

»6ft USB Data Cable

Page 4

Main Control Panel

Rx Input Card (KD-HDUIC)

Tx Output Card (KD-HDUOC)

HDMI Input and Output Numbering

The KD-HDMS8x8 in its default conﬁguration contains 8 Input cards and 8 Output cards. The Input

cards are addressed from 01-08, and the Output cards from 01-08.

Power

12V/8.33A (100W)

Power Supply

Rear IR Eye (Receiver)

Rear IR receiver for

remote control

Operation Mode Switch

Switch to “Program” mode

when updating ﬁrmware

For manufacturers use only

Serial IR

To Input from Control interface

for controlling unit via Serial IR

and IR routing

RS-232

The main RS-232/DB9

port for interfacing with

a control system.

USB

The USB port is for

software upgrades only.

It is not used for control

interface.

TCP/IP

This is the main TCP/IP port for interfacing

with control systems. It supports the same

control commands as the RS-232 port

and it can support TCP/IP to RS-232

conversion & routing and TCP/IP to serial

IR conversion & routing.

Serial IR / RS-232

Use the KD-HDMS as a Control Router for

devices integrated into your system

Serial IR / RS-232

Use the KD-HDMS as a Control Router for

devices integrated into your system

Left Analog Audio / PCM Audio Input

Supports Left channel Analog Audio Input or

use for Coaxial Digital Audio Input

Left Analog Audio / PCM Audio Output

Send Left channel Analog Audio or Coaxial

Digital Audio to your Display or other devices

CAT5 Input

Integrate a remote source by using the KD-BBTX

Transmit Balun to feed the CAT5 inputs

CAT5 Output

Use the KD-BBRX Receive Balun to carry Video,

Audio, and Control to your Display (or other) devices

Right Analog Audio Input

Supports Right channel Analog Audio Input

Right Analog Audio Output

Send Right channel Analog Audio

to your Receiver or other devices

Link LED

Indicates that input connection is stable

Link LED

Indicates that output connection is stable

HDMI Input

To Input source components

HDMI Output

To Output to Display

Page 5

Application Example

DVI Video*

L /R/PCM

CAT5/5e/6

L /R/PCM

CAT5/5e/6

L /R/PCM

CAT5/5e/6

Speakers

HDMI

Blu-Ray

Satellite 1

Desktop PC Desktop PC

Display 8Display 4

Control System

DVI

HDMI/DVI

Audio

CAT5/6/7

IR/RS-232

HDMI

Blu-Ray

HDMI

IR/RS-232

IR/RS-232 & TCP/IP

HDMI

IR/RS-232

HDMI

IR/RS-232

HDMI

IR/RS-232

HDMI

IR/RS-232

HDMI

IR/RS-232

HDMI

Display 7

Display 3

Display 2

Display 5

Display 1 Display 6

Display 2a

Display 1a

(mirrored) (mirrored)

Satellite 2 Cable 1 Cable 2

KD-BBTXKD-BBTX

KD-BBTX KD-BBTX

KD-BBRXKD-BBRXKD-BBRXKD-BBRX

KD-HDMS8X8

Transmits:

»1080p/60Hz resolution up to 140 ft

»1080p/24, 1080i, 720p and 480i/p resolutions up to 270 ft

» When used with KD-BBRX Receiver Baluns

RS232 Control

Serial IR

USB

TCP/IP

Optical IR

Surround Rcvr.

*To connect DVI use HDMI to DVI adapters

270’

180’

200’

150’

Page 6

Quick Setup Guide

Initial Setup & Operation for HDMI via Front Panel

The KD-HDMS8x8 is set by default to HDMI Input. To change these default settings please see

“Initial Setup & Operation via CAT5 Baluns” section below.

1. Insert HDMI cables into card slots 1 through 16

»Slots 1-8 are labeled Rx, and are Input Card Slots 1-8.

»Slots 9-16 are labeled Tx, and are Output Card Slots 1-8.

»Connect your source components to the Input cards

»Connect your displays to the Output cards

»Power up all sources and displays

2. Establish an HDMI Handshake for Each Source

»Push the left selector to access the Main Menu choices

»Using the left selector, scroll to the “7-EDID Setup” Menu

»Press the right selector to navigate to the EDID sub-menus

»With the left selector, scroll to the Input source you wish to copy the EDID to

»Using the right selector, scroll to the HDMI or CAT5 Output you wish to establish an HDMI

handshake for, or select a Default EDID 01-08 from the EDID library (see pg.10)

»Press the right selector to set the Handshake for that combination

»Continue this procedure for all Inputs

»The EDID control and HDMI input set up is stored in a non-volatile memory back up and is

only required during initial set up or when a new display or source is added to the system.

»Establish a default handshake for ALL Inputs:

»Using the ‘7-EDID Setup’ Menu, select ‘ALL Inputs’ and scroll to the Output number

you wish to copy the EDID from (HDMI, CAT5 or a Default EDID setting) and press

the right selector

3. Switching via Front Panel

»Push the left selector to access the Main Menu choices

»Using the left selector, scroll to the “1-Video Switch” Menu

»Press the right selector to navigate to the Video Switch sub-menus

»Using the left selector, scroll to the Output you wish to select

»Using the right selector, scroll to the Input you wish to select

»Finally, press the right selector to make the switch

4. Sending your output via KD-BBRX CAT5 Receive Balun(s)

»Both HDMI and CAT5 Outputs are active on all Output Card Slots, therefore no conﬁguration

is necessary to activate the CAT5 Output for each Tx Card Slot.

5. Sending your source via KD-BBTX CAT5 Transmit Balun(s)

»Set dipswitch #2 of the KD-BBTX Balun to “DDC” in order to establish a proper HDMI

handshake

»Conﬁgure the appropriate Input Card Slot to activate its CAT5 input using the

“6-Video Input Setup”

Page 7

Initial Setup & Operation via CAT5 Baluns

When using Key Digital Baluns (RX/TX) you must use the following procedure to correctly format

both the baluns and HDMS8x8 matrix switcher for correct operation.

»NOTE: Slots 1-8 are inputs, slots 9-16 are outputs.

»The KD-BBTX Dipswitch #2 MUST be set to the DDC position.

½IMPORTANT: Make sure that you power up all baluns, sources and displays.

Conﬁrm that you have an active connection on the Balun indicated by the solid

red “LINK” LED.

1. By default, the KD-HDMS8x8 is configured to accept a direct HDMI connection. When using

a KD-BBTX, you MUST change the input mode from HDMI to CAT5 to enable the switcher to

“see” the CAT5/Balun input. Select “6-Video Input Setup” from the main menu. Press the right

selector to navigate to the sub-menus. Using the left selector, scroll to the Input number you

wish to change. Using the right selector, scroll to select “CAT5” and press the right selector to

enter your choice.

2. Repeat procedure for any other input where a KD-BBTX is being used.

3. Once you have correctly configured the inputs to accept either HDMI and/or CAT5/Balun, you

need to establish the correct HDMI “handshake”.

4. See previous section on establishing an HDMI handshake.

Front Panel Menu Selection Controls:

Power On

½The unit will power up with a push on either the left or right Selector.

Power Off

½The unit will power off through IR, Remote, RS-232 or TCP/IP commands only.

Left Selector

½Main Menu: To access the Main Menu push this selector once.

½To Select Main Menu Options: Turn selector left or right to select Menu Options 1-9

½Sub-Menu values: Turn this selector to scroll through the sub-menu selections. There will be left

and right sub-menu choices. Use the left selector to change left side options

½To Go-Back to a previous menu: from whatever menu you are presently in you may return to the

previous menu by pressing this selector once. You will return to the menu you were previously in.

Dispwitch # - Select DDC

Page 8

Right Selector

½Sub-Menu: After selecting a speciﬁc Main Menu (1-9) option with the left selector, press the right

selector to select its Sub-Menu. You will be taken to the sub-menu for the main menu option you

had previously selected.

½Sub-Menu values: Turn this selector to scroll through the sub-menu selections. Use the right

selector to change right side options. After a sub-menu choice has been made, push this

selector once to enter it. The display will blink to acknowledge your choice.

Menu Tree on LCD Display

Main Menu Selections:

Using the left selector, choose from the following Main Menu options;

1. Video Switch

2. Audio Switch

3. Volume Control

4. Audio Output Set Up

5. Audio Input Set Up

6. Video Input Set Up

7. EDID Set Up

8. TCP/IP Set Up

9. Factory Default

Using the right selector, push to enter the sub-

menu for any of the selected main menu options above;

Sub-Menu Selections:

1. “Video Switch” options:

»Output 01–08

»All Outputs

Use the left selector to choose these.

For each Output number selected, ‘01-08’ and ‘All’, there are Input sub-menu choices;

»Input 01–08

Use the right selector to choose these and push to conﬁrm your choice for both

Select an Output number with the left selector and then select an Input number you wish to feed

that output by turning the right selector. Push the right selector to select that combination. The

display will blink to acknowledge your choice. This will immediately switch your Output to the Input

selected.

2. “Audio Switch” options:

»Output 01-08 plus All Outputs

Use the left selector to choose these.

For each Output number selected, ’01-08’ and ‘All’, there are Audio sub-menu choices:

Page 9

»HDMI

»External Analog

»External Digital

»CAT5

Use the right selector to choose these and push to conﬁrm choice.

These correspond to which Audio signal type will be passed to the selected Output number from

your previously selected Input number.

3. “Volume Control Set Up” options:

»Output 01-08 plus All Outputs

Use the left selector to choose Output number desired.

Use the right selector to choose Volume level desired (00-99) and push to conﬁrm choice.

Continue for all Outputs you wish to change

4. “Audio Output Set Up” options:

»Output 01-08 plus All Outputs

Use the left selector to choose these.

For each Output number selected, ’01-08’ and ‘All’, there are Audio Output sub-menu choices:

»Digital

»Analog

Use the right selector to choose these and push to conﬁrm choice.

These correspond to the RCA connectors only and choose which format will be passed to the

Output selected.

5. “Audio Input Set Up” options:

»Input 01-08 plus All Inputs

Use the left selector to choose these.

For each Input selected, ’01-08’ and ‘All’, there are Audio Input sub-menu choices;

»Digital

»Analog

Use the right selector to choose these and push to conﬁrm choice.

These correspond to the RCA connectors only and choose which format will be accepted by the

Input selected.

6. “Video Input Set Up” options:

»Input 01-08 plus All Inputs

Use the left selector to choose these.

For each Input selected, ‘01-08’ and ‘All’, there are Video Input type sub-menu choices:

»HDMI

»CAT5

Use the right selector to choose these and push to conﬁrm choice.

Page 10

7. “EDID Set Up” options:

»Input 01-08 plus All Inputs

Use the left selector to choose these.

For each Input selected, ’01-08’ and ‘All’, there are EDID Set Up sub-menu choices:

»HDMI Output 01 through 08

»CAT5 Output 01 through 08

»For each Input (source) selected with the left selector there is a choice to copy the EDID

information from either the HDMI or CAT5 connected Output (display) using the right

selector depending on which is connected. Both HDMI and CAT5 Inputs will receive the

copied EDID information.

»The Default choices (listed below) copy the EDID from a stored library of EDID conﬁgurations

to the selected Input card across both HDMI and CAT5 Inputs.

»Default EDID 1 – (1080i 2CH PCM)

»Default EDID 2 – (1080p 2CH PCM)

»Default EDID 3 – (1080i PCM, DTS/DOLBY. not including HD audio)

»Default EDID 4 – (1080p PCM, DTS/DOLBY. not including HD audio)

»Default EDID 5 – (1080i every audio including HD audio)

»Default EDID 6 – (1080p every audio including HD audio)

»Default EDID 7 – (3D 1080p 2CH PCM)

»Default EDID 8 – (3D 1080p every audio including HD audio)

Use the right selector to choose these and push to conﬁrm choice. You will receive a “Completed”

message when successful, or a “Failed” message if unsuccessful.

8. “TCP / IP” options:

»IP address

»Sub net Mask

»Port

½The default IP address is; ‘192.168.000.233’ This can be changed to accommodate your

particular conﬁguration or controller.

½The default Sub net mask is ‘255.255.255.000’ and may also be changed to accommodate your

particular conﬁguration.

½The default Port number is ‘23’

Select the TCP/IP option by pressing the right selector. Highlight the group of numbers you wish to

change by turning the left selector. Change the group of numbers using the right selector. Continue

this procedure until all numbers are chosen. Press the right selector to enter the changes. You may

then press the left selector to return to the previous menu if desired.

9. “Factory Default” options:

This option will return the unit to its Factory Default settings. Please see the list of default settings

below. When this menu option is chosen, you will be presented with a choice of EDID’s from the

default EDID library. Choose one of these default EDID’s (typically default 1-1080i 2Ch PCM) using

the left selector, then press the right selector to conﬁrm. The unit will then reset to the default

conﬁguration including the EDID you have chosen.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Key Digital Matrix-Umschalter Handbücher

Key Digital

Key Digital KD-MSV8X8 Bedienungsanleitung

Key Digital

Key Digital KD-MSW4X2 Bedienungsanleitung

Key Digital

Key Digital KD-4x8CS Champion Bedienungsanleitung

Key Digital

Key Digital KD-MSW8X4Pro Bedienungsanleitung

Key Digital

Key Digital KD-HDMS8X8 Bedienungsanleitung

Key Digital

Key Digital KD-Pro6x6CC Bedienungsanleitung

Key Digital

Key Digital KD-MSWCAT4x4 FatBOY Bedienungsanleitung

Key Digital

Key Digital KD-4x2CS Champion Bedienungsanleitung

Key Digital

Key Digital KDUPS52USB Bedienungsanleitung

Key Digital

Key Digital FatBOY KD-MSA8X8Pro Bedienungsanleitung

Key Digital

Key Digital KD-HD16x16ProK Bedienungsanleitung

Key Digital

Key Digital KD-4x4CSK Bedienungsanleitung

Key Digital

Key Digital KD-MSV8X8 Bedienungsanleitung

Key Digital

Key Digital KD-MSW 8x3 Bedienungsanleitung

Key Digital

Key Digital KD-CATRCAAA Bedienungsanleitung

Key Digital

Key Digital KD-MSWCAT8x8 FatBOY Montage- und Bedienungsanleitung

Key Digital

Key Digital Phantom KD-HDMSW4X4 Bedienungsanleitung

Key Digital

Key Digital KD-MXA8X8Pro FatBOY Bedienungsanleitung

Key Digital

Key Digital KD-MSW8X4Pro Bedienungsanleitung

Key Digital

Key Digital KD-2X2CS Champion Bedienungsanleitung

Key Digital

Key Digital KD-MSW4x2Pro Bedienungsanleitung

Key Digital

Key Digital KD-MLV4x4Pro Bedienungsanleitung

Key Digital

Key Digital KD-HD4x4 Bedienungsanleitung

Key Digital

Key Digital KD-MS4x4G Bedienungsanleitung

Beliebte Matrix-Umschalter Handbücher anderer Marken

Broadcast Tools

Broadcast Tools SS 8.2 Bedienungsanleitung

Altimium

Altimium MATF32 Bedienungsanleitung

ALFAtron

ALFAtron ALF-MUK44N Bedienungsanleitung

Monoprice

Monoprice Blackbird 15377 Bedienungsanleitung

Kramer

Kramer XL 3216VS Bedienungsanleitung

PTN

PTN FMX12 Bedienungsanleitung

CYP

CYP nT15GX01 Bedienungsanleitung

Kramer

Kramer VP-2x2 Bedienungsanleitung

Kramer

Kramer Sierra Video 6432V5xl Bedienungsanleitung

TESmart

TESmart HMA0402A40 Bedienungsanleitung

Octava

Octava HD4XSTPMX Bedienungsanleitung

Intelix

Intelix FLX-88 Betriebsanleitung

Kramer

Kramer LASSEN XL 3232S Bedienungsanleitung

Roland

Roland XS-1HD Bedienungsanleitung

Kramer

Kramer VS-66HDCPxl Bedienungsanleitung

Atlona

Atlona AT-HDMI-22M Bedienungsanleitung

Link

Link HD8X8 Bedienungsanleitung

AMX

AMX AVS-OP-2020-117 Anleitungen und Rezepte