Keysight Technologies B2900A Series Bedienungsanleitung

Keysight Technologies

Making Current-Voltage Measurement Using B2901A/02A/11A/12A - Demo Guide

B2900A Series Precision Source/Measure Unit

Measurement concept

– Source voltage to turn the LED on.

– Limit value feature prevent the instrument from

sourcing too much even if Source value is increased.

– Step voltages from start voltage to stop voltage with

making current measurement at each voltage step.

– Voltage steps are sourced from an internal voltage

source.

– Current measurements are made by an internal

current meter.

– The complicated measurement as above can be

congured and made easily with Intuitive Graphical

User Interface (GUI).

– Current-voltage curve can be seen easily by changing

View mode.

Setup

1. Connect the yellow banana plug to Ch 1 Low Force terminal.

2. Connect the red banana plug to Ch 1 High Force terminal.

3. Clip the LED cathode terminal with the black gold-plated

tweezers.

4. Clip the LED anode terminal with the red gold-plated tweezers.

b. Press and set Channel 1 Limit value to 100 mA.

c. Press Ch1 to turn on Channel 1 Output relay.

d. Press and rotate until Source value achieves 3 V.

You will see the measurement parameters turn orange, which

means they reach Limit value.

e. Rotate until Source value achieves 2 V and then press

to set Source value to 2 V.

1. Turn on the LED and measure LED current

1-1. Change View mode to Single View

a. Press repeatedly until Single View

for Channel 1 is shown in the display.

1-2. Source voltage to turn on the LED

a. Press to edit Channel 1 Source value, and then enter

2 V to set Source value to 2 V.

Procedure overview

1. Turn on the Light Emitting Diode (LED) and measure LED

current

2. Make current-voltage (I-V) sweep measurement to get LED

I-V characteristics

Objective

This demo shows how easily current-voltage character-

istics can be obtained with the B2900A Series through

the LED characteristics measurement.

Required Instrument and Accessory

You will see LED is turned on

because voltage is sourced by

the channel

Keysight B2901A/02A/11A/12A

Precision Source/Measure Unit

LED lampKeysight 11059A

Kelvin Probe Set

Current [A]

Voltage [V]

LED Current-Voltage Characteristics

Source

Meas

B2900 Series

0.20

0.15

0.10

0.05

0.00

0.50.0 1.0 1.5 2.0 2.5 3.0

High force

Ch 1

Low force

LED

Red

(11059A)

Yellow

(11059A)

Black

(11059A)

Red

(11059A)

Cathode

Anode

1-3. Make measurement of the LED current

a. Press to perform a single point measurement.

b. Press to repeat single point measurements periodi-

cally.

c. Press to stop making measurements periodically.

1-4. Turn off the channel output

a. Press to edit Channel 1 Source value, and then enter

0 V to set Source value to 0 V.

b. Press Ch1 to turn off Channel 1 Output relay.

2. Make current – voltage sweep measurement

2-1. Change View mode to Single View

a. Press repeatedly until

Single View for Channel 1 is

shown in the display.

2-2. Congure the condition to source and measure

a. Press , then press to set Channel 1 V/I Source

Function to V Source. (If can’t be found on the Assist

keys, press to change the keys.)

b. Press and set Channel 1 Limit value to 100 mA.

c. Press , then press to set Channel 1 Measure-

ment Parameter to Current.

2-3. Change View mode to Graph View

a. Press repeatedly until

Graph View is shown in the

display.

2-4. Perform the measurement

a. Press Ch1 to turn on Channel 1 Output relay, and

then press to perform a sweep measurement. During

the measurement, the status will be shown.

2-5. View the measurement result graph

a. Press to adjust the scale of the graph after nishing

the measurement.

This information is subject to change without notice.

Published in USA, February 27, 2015

5991-3951EN

www.keysight.com

Keysight | Making Current–Voltage Measurement Using B2901A/02A/11A/12A - Demo Guide

Measurement parameters

are updated whenever

Trigger Button is pressed

Measurement parameters

are updated periodically

Source Shape

Sweep Sub-Panel

“Auto” indicator is turned on

“Auto” indicator is turned off

d. Press , and then press to show Sweep

Sub-Panel.

e. Press , then press to turn on Single Linear Sweep

Mode. After turning on Single Linear Sweep Mode, you can

see Source Shape which shows the single linear sweep

mode.

f. Rotate to select Channel 1 Sweep Parameters and set

them up as below. (Start: 0 V, Stop: 2 V, Points: 101, Step:

20 mV)

2-6. Change the graph scale

a. To change the graph scaling of Y-axis from LINEAR to LOG,

rotate and press to select Y-axis scaling.

b. To change the graph scale value of Y-axis, rotate and press

to modify Y-axis scale value.

2-7. View the list of the measurement data

a. To see the list of the measurement result, press ,

then press to open Measure Result dialogue.

b. Rotate and press to select List Area. Then rotate

to scroll the data list.

For other unlisted countries:

www.keysight.com/nd/contactus

www.keysight.con/nd/precisionSMU

Andere Handbücher für B2900A Series

Dieses Handbuch passt für folgende Modelle

Andere Keysight Technologies Messgerät Handbücher

Keysight Technologies

Keysight Technologies X Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies U1281A Bedienungsanleitung

Keysight Technologies

Keysight Technologies N5241B Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies X Series Betriebsanleitung

Keysight Technologies

Keysight Technologies PNA-L N5230A Bedienungsanleitung

Keysight Technologies

Keysight Technologies FieldFox N9912A104 Bedienungsanleitung

Keysight Technologies

Keysight Technologies N9322C Bedienungsanleitung

Keysight Technologies

Keysight Technologies MXA Series Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies B2900B Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies E5080B Bedienungsanleitung

Keysight Technologies

Keysight Technologies M9216A Benutzerhandbuch

Keysight Technologies

Keysight Technologies N9020B Handbuch

Keysight Technologies

Keysight Technologies EXA N9010B Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies N4373E Bedienungsanleitung

Keysight Technologies

Keysight Technologies M9393A Bedienungsanleitung

Keysight Technologies

Keysight Technologies U4431A Bedienungsanleitung

Keysight Technologies

Keysight Technologies B1500A Installationsanleitung

Keysight Technologies

Keysight Technologies N1060A Bedienungsanleitung

Keysight Technologies

Keysight Technologies E5868A Montageanleitung

Keysight Technologies

Keysight Technologies B1505A Bedienungsanleitung

Keysight Technologies

Keysight Technologies M9300A Benutzerhandbuch

Keysight Technologies

Keysight Technologies Agilent Technologies PXI Express M9202A Benutzerhandbuch

Keysight Technologies

Keysight Technologies N5511A-K26 Bedienungsanleitung

Keysight Technologies

Keysight Technologies N9344C Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung