Keysight Technologies EXA N9010B Installations- und Betriebshandbuch

Option B40, 40 MHz Analysis Bandwidth

and Microwave Preselector Bypass (MPB) Upgrade Kit

Keysight Technologies

N9010B EXA and N9020B

MXA Signal Analyzer

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9020-90253

Edition

Edition 1, September 2018

Supersedes February 2016

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9020-90253 3

Option B40, 40 MHz Analysis Bandwidth (B40) and Microwave Preselector Bypass (MPB) Upgrade

Kit

Option B40, 40 MHz Analysis Bandwidth (B40) and Microwave

Preselector Bypass (MPB) Upgrade Kit

Software and test equipment is required for making adjustments and for performance verification

testing.

Information on how to obtain this software can be found at:

www.keysight.com/find/calibrationsoftware

While Keysight does recommend that a full calibration be performed after the installation of this

upgrade, the end user must ultimately determine whether they want this service or not. If a full

calibration is required, arrangements regarding the level of calibration must be made between the

end user and the calibration provider.

Products Affected: N9010B EXA Signal Analyzer

N9020B MXA Signal Analyzer

Serial Numbers:

Options: B40, MPB

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

( ) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

3.0 Hours

5.5 Hoursa

3.5 Hoursa

a. To ensure that these newly installed options are functioning properly, the procedure that follows

includes the requirement of performing certain adjustments and performance verification tests.

However, the completion of these tests does not guarantee that the instrument meets all advertised

specifications.

4Installation Note N9020-90253

Introduction

This kit includes parts to upgrade any N9010B EXA or N9020B MXA signal analyzer to add Option

B40, 40 MHz analysis bandwidth. If the analyzer has frequency range Options 507, 508, 513, or

526, hardware and licenses for Option MPB, microwave preselector bypass will also be installed.

Some parts might not be necessary if other certain options are already installed (if applicable).

In addition to installing the hardware to support Option B40, licenses for the following options will

also be installed (where "x" is 1 for EXA or 2 for MXA):

— N90x0B-B40, 40 MHz Analysis Bandwidth

— N9020B-S40, 40 MHz/Channel Baseband Bandwidth

(for use with Option BBA, if also installed)

— N90x0B-DP2, Digital Processor & 2 GB Capture Memory

— N90x0B-RTL, Real Time Link

— N9020A-MPB, Microwave Preselector Bypass

— N90x0B-FS1, Fast Sweep Capability

The installation procedure begins with an “inventory” of the analyzer serial number,

currently-installed options, installed hardware, and software version. This information will be used

to determine which sub-procedures, if any, can be skipped.

Installation Note N9020-90253 5

Introduction

Installation Kit Parts List

Quantity Description Keysight Part Number

1 A3 40 MHz Digital IF Assembly N9020-60016

1 A15 Front End Controller w/ IF MUX N9020-60172

1 Opt B40/BUN Cable Kit with Wire Markers (includes cables W36, W37,

W38, W39, W41, W42, and W50 listed below)

N9020-60301

1 Coaxial Fixed Attenuator, DC to 26.5 GHz, Option 006, PB Free (AT1) 08493-60026

1 Bracket, PS Bypass Switch 1 E4410-00104

1 Bracket, PS Bypass Switch 2 E4410-00110

1 Cable Assembly, SW - SW2 (W31) E4410-20161

1 Cable Assembly, Switch 2 - YIG Tuned Filter (W32) E4410-20163

1 Cable Assembly, Switch 1 - RF Assembly (W34) E4410-20164

1 Cable Assembly, YIG Tuned Filter - Switch 1 (W33) E4410-20165

1 Cable RF Switch 1 - Switch 2 (W35) N9020-20210

1 Cable Assembly, Switch Control (W30) E4410-60159

2 Coaxial Switch (SW1 and SW2) N1810-60069

1 Cable Assembly, Coaxial 530 mm LG (W50) 8121-1401a

with ends labeled ‘726’ and '17'

1 Cable Assembly, Coaxial 380mm LG (W42) 8121-2288a

with ends labeled ‘716’ and ‘14’

1 Cable Assembly, Coaxial 530 mm LG (W37) 8121-1401a

with ends labeled ‘900’ and ‘100’

1 Cable Assembly, Coaxial 620 mm LG (W38) 8121-1861a

with ends labeled ‘901’ and ‘15’

1 Cable Assembly, Coaxial 240 mm LG (W36) 8121-1862a

with ends labeled ‘902’ and ‘7’

1 Cable Assembly, Coaxial 280 mm LG (W41) 8120-8868a

with ends labeled ‘601’ and ‘19’

1 Cable Assembly, Coaxial 525 mm LG (W39) 8121-2028a

with one end labeled ‘1100’

1 Screw, M3 x 0.5, (8 mm long), Pan head 0515-0372

4 Screw, M2.5 x 0.45, (20 mm long), Pan head 0515-1992

14 Screw, M3 x 0.5, (6 mm long), Flathead 0515-1946

6Installation Note N9020-90253

Introduction

12 Cable Tie, Self-Locking, Nylon Gray 1400-0249

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate, Preselector Bypass Upgrade 5972-3380

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

a. This cable is included in the Option B40/BUN Cable Kit with Wire Markers, p/n N9020-60301

Quantity Description Keysight Part Number

Installation Note N9020-90253 7

Introduction

Tools Required

—T-8TORXDriver

—T-6TORXDriver

— T-10 TORX Driver

— T-20 TORX Driver

— 5/16-inch torque wrench

— 9/16-inch nut driver

— 1/4-inch socket on 4-pound torque wrench

— Scissors or knife

—Diagonalcutters

— Keysight Calibration and Adjustment Software, N7814A (revision E.14.00 or later)

— Test equipment and computer supported by the X-Series Performance Tests and Adjustment

Software

— EXA Signal Analyzer Service Guide or MXA Signal Analyzer Service Guide, as appropriate. These

Service Guides can be downloaded using the following links:

www.keysight.com/find/N9010B_service_guide

www.keysight.com/find/N9020B_service_guide

— Microsoft Windows based personal computer with internet access and USB port

— USB storage device with >2GB free memory

Initial Instrument Functionality Check

Power on the instrument and allow the instrument to boot up. Run an alignment and display the

measurement screen. (The instrument will probably display a spectrum analyzer screen and you will

see the instrument sweeping.)

There should be no alignment failures. If there are failures, investigate and fix the problem before

continuing.

Before you disassemble the instrument, turn the power switch to Standby. After the instrument

has completely shut down, unplug the instrument. Failure to unplug the instrument can result in

personal injury.

Electrostatic discharge (ESD) can damage or destroy electronic components. All work on

electronic assemblies should be performed at a static-safe workstation. Refer to the

documentation that pertains to your instrument for information about static-safe workstations

and ordering static-safe accessories.

8Installation Note N9020-90253

Installation Procedure

Analyzer Information

1. Connect a power cord to the analyzer and turn on the analyzer.

2. After the analyzer has completed turning on, press System, Show System. Make note of the

following information from the Show System screen:

Product Number ________________

Serial Number ________________

Instrument S/W Revision ________________

3. Check for the presence of the options listed below in the Show System screen. Put a check

mark or “X” after each option listed below that appears in the Show System menu.

—N9010B-503 or N9020B-503 ____

—N9010B-507 or N9010B-513 or N9010B-526 ____

—N9010B-532 or N9010B-544 ____

—N9020B-508 or N9020B-513 or N9020B-526 ____

—N9010B-B25 or N9020B-B25 ____

—N9020B-BBA ____

—N9010B-CR3 or N9020B-CR3 ____

—N9010B-CRP or N9020B-CRP ____

—N9010B-B40 or N9020B-B40 ____

—N9010B-DP2 or N9020B-DP2 ____

—N9010B-MPB or N9020B-MPB ____

Refer to the following conditions:

—If the analyzer is equipped with either N9010B-B40 or N9020B-B40, do not proceed with

the installation of this upgrade kit. If either of these options are already installed, you do not

need this upgrade kit, since the necessary license and hardware is already present.

—If the analyzer has N9010B-532 or N9010B-544, do not proceed with the installation of this

kit. This kit can only be installed on analyzers with frequency range options of 503, 507,

508, 513, or 526.

If the upgrade kit is N9010BU-B40 and the product number is N9010B, or if the upgrade kit is

N9020BU-B40 and the product number is N9020B, you may proceed with the installation of this

kit. Do not attempt to install upgrade kit N9010BU-B40 on an N9020B and similarly do not

attempt to install upgrade kit N9020BU-B40 on an N9010B.

Installation Note N9020-90253 9

Installation Procedure

—If the analyzer’s frequency range option is either N9010B-503 or N9020B-503, you do not

need to perform the Install Preselector Bypass Hardware procedure. Also, you should not

redeem the entitlement for N9010B-BUP or N9020B-BUP (as appropriate). The Install

Preselector Bypass Hardware procedure and the entitlement for N9010B-BUP and

N9020B-BUP are only for analyzers with frequency range options 507, 508, 513, or 526.

4. On the analyzer, press System, Show Hardware. Note the Part #, Matl Rev, Rev, OF Rev, and

Hw Id of the Front End Controller in the table below.

5. Refer to step 3 and 4:

—If the analyzer has N9010B-CR3, N9010B-CRP, N9020B-CR3, and/or N9020B-CRP installed

verify that it also has a Front End Controller with Hw Id of 41 or 75. If the Front End

Controller has a Hw Id of 41 or 75, you do not need to perform the Replace Front End

Controller procedure.

—If the analyzer has N9010B-DP2, N9010B-MPB, N9020B-DP2, and/or N9020B-MPB

installed, verify that it also has a Front End Controller with Hw Id of 75 or 170 and a Digital

IF with Hw Id of 34. If any of the listed options is present and the Front End Controller has

Hw Id of 75 or 170 and the Digital IF has Hw Id of 34, all the necessary hardware is already

installed. It is only necessary to redeem the license entitlement for B40 and perform the

necessary adjustments and performance verification tests.

Assembly Name Part # Matl Rev Rev OF Rev Hw Id

Front End Controller

Digital IF

10 Installation Note N9020-90253

Installation Procedure

Update Instrument Software

Updating the instrument software and installing the necessary licenses before installing the new

hardware will help ensure that the hardware installation was successful.

Go to the following website and determine whether or not the analyzer has the latest instrument

software already installed:

http://www.keysight.com/find/xseries_software

If the analyzer does not have the latest instrument software already installed, download and install

the latest version.

Andere Handbücher für EXA N9010B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Keysight Technologies Messgerät Handbücher

Keysight Technologies

Keysight Technologies 86120D Bedienungsanleitung

Keysight Technologies

Keysight Technologies MXA Series Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies B1505A Bedienungsanleitung

Keysight Technologies

Keysight Technologies E4981A Betriebsanleitung

Keysight Technologies

Keysight Technologies N9020B Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies 34972A Bedienungsanleitung

Keysight Technologies

Keysight Technologies N9020A Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies N9344C Bedienungsanleitung

Keysight Technologies

Keysight Technologies W3301A Bedienungsanleitung

Keysight Technologies

Keysight Technologies B1507A Bedienungsanleitung

Keysight Technologies

Keysight Technologies N5251A Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies B2901A Bedienungsanleitung

Keysight Technologies

Keysight Technologies E5260 Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies N9322C Bedienungsanleitung

Keysight Technologies

Keysight Technologies N4374B Bedienungsanleitung

Keysight Technologies

Keysight Technologies E2655C Bedienungsanleitung

Keysight Technologies

Keysight Technologies U2000 Series Bedienungsanleitung

Keysight Technologies

Keysight Technologies N9010B Installations- und Betriebshandbuch

Keysight Technologies

Keysight Technologies N9340B Bedienungsanleitung

Keysight Technologies

Keysight Technologies EPM-P Series Betriebsanleitung

Keysight Technologies

Keysight Technologies 34420A Bedienungsanleitung

Keysight Technologies

Keysight Technologies N5244BU-679 Bedienungsanleitung

Keysight Technologies

Keysight Technologies 11590B Service-Handbuch

Keysight Technologies

Keysight Technologies 53147A Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung