Keysight MXA 902 Series Installations- und Betriebshandbuch

Notice: This document contains references to Agilent.

Please note that Agilent’s Test and Measurement busi-

ness has become Keysight Technologies. For more in-

formation, go to www.keysight.com.

Keysight MXA Signal Analyzer

Option HLB, 40 MHz to 85 MHz Analysis

Bandwidth Upgrade

Serial Prefix < MY/SG/US5233

Installation Note

Part Number N9020-90239

Printed in USA August 2014

Notice.

The information contained in this document is subject to change without notice.

Agilent Technologies makes no warranty of any kind with regard to this material, including but not

limited to, the implied warranties of merchantability and fitness for a particular purpose. Agilent

Technologies shall not be liable for errors contained herein or for incidental or consequential damages in

connection with the furnishing, performance, or use of this material.

Installation Note N9020-90239 3

Option HLB, 40 MHz to 85 MHz Analysis Bandwidth Upgrade Serial Prefix <MY/SG/US5233

Option HLB, 40 MHz to 85 MHz Analysis Bandwidth Upgrade

Serial Prefix <MY/SG/US5233

Introduction

This installation note explains how to install the hardware and provides guidelines for adjustment and

verification for Option HLB, 40 MHz to 85 MHz Analysis Bandwidth Upgrade for MXA signal

analyzers with serial number prefixes <MY/SG/US5233. A similar kit, Option HLC, is available for

newer MXA signal analyzers.

Installing this kit requires that the analyzer already have hardware and licenses installed to provide

analysis bandwidths up to 40 MHz. If the analyzer does not already have the necessary hardware and

licenses to provide analysis bandwidths up to 40 MHz, other upgrade kits are available.

Refer to http://www.agilent.com/find/mxa_upgrades for information of available upgrades.

If the analyzer already has Options MPB and/or DP2 installed, the upgrade to 40 MHz analysis

bandwidth, N9020AK-B40, can be installed at the same time as this kit.

There are also license-key-enabled upgrades to allow the analysis bandwidths provided by this kit to

be further extended to 125 MHz or 160 MHz. These kits are N9020AK-BU4 (85 MHz to 125 MHz

upgrade) and N9020AK-BU5 (85 MHz to 160 MHz upgrade). The N9020AK-BU4 or N9020AK-BU5

kits can also be installed at the same time as the N9020AK-HLB kit.

Products Affected: N9020A, MXA Signal Analyzer

Serial Numbers: < MY52330000

< SG52330000

< US52330000

Options: B40, MPB

To Be Performed By: (X) Agilent Service Center

(X) Personnel Qualified by Agilent

( ) Customer

Estimated Installation Time:

Estimated Adjustment Time:

Estimated Verification Time:

2.0 Hours

1.5 Hours

4.0 Hours

4Installation Note N9020-90239

Option HLB, 40 MHz to 85 MHz Analysis Bandwidth Upgrade Serial Prefix <MY/SG/US5233

Software and test equipment is required for making adjustments and for performance verification

testing.

Information on how to obtain this software can be found at:

www.agilent.com/find/calibrationsoftware

NOTE Instrument software revision A.13.15 or later is required to install this upgrade.

NOTE The instrument must be readjusted and the performance tested to assure the

instrument meets specifications following the hardware installation. The X-Series

Performance Verification and Adjustment Software must be used. All adjustments

are automated. This software is included in the N7814A, Agilent X-Series Signal

Analyzer Calibration Application software.

Installation Note N9020-90239 5

Option HLB, 40 MHz to 85 MHz Analysis Bandwidth Upgrade Serial Prefix <MY/SG/US5233

Installation Kit Parts List

Quantity Description Agilent Part Number

1 Power Supply, AC/DC Switching 350W 12-Output 0950-5012

1 A3 40 MHz Digital IF Assembly N9020-60016

1 A25 Wideband Analog IF N9020-60044

1 A26 Wideband Digital IF N9020-60257

1 A16 MXA Reference Assembly N9020-60200

1 Rear Panel Replacement Kit, MXA Prefix MY/SG/US5233 N9020-60149

1 Reference Support Bracket E4410-00108

1 Opt HLB/HLC Cable Kit with Wire Markers

(includes cables W51 through W56, listed below) N9020-60153

1 Cable Assembly, 2nd LO, LO Synth (W6) N9020-20033

1 Cable Assembly, Ref, Front End (W5) N9020-20064

1 Cable Assembly, Ref, Attenuator A (W19) N9020-20065

1 Cable Assembly, Flat Flexible 80-conductor 3-in-LG (W44) 8121-1854

1 Cable Assembly, Coaxial 700 mm LG (W20) 8121-1400a

with ends labeled

‘705’ and ‘6’

a. This cable is included in the Option HLB/HLC Cable Kit with Wire Markers, p/n N9020-60153

1 Cable Assembly, Coaxial 530 mm LG (W51) 8121-1401a

with ends labeled

‘301’ and ‘718’

1 Cable Assembly, Coaxial 380 mm LG (W52) 8121-2288a

with ends labeled

‘102’ and ‘15’

1 Cable Assembly, Coaxial 380 mm LG (W54) 8121-2288a

with ends labeled

‘716’ and ‘14’

1 Cable Assembly, Coaxial 480 mm LG (W55) 8121-2290a

with ends labeled

‘805’ and ‘17’

1 Cable Assembly, Coaxial 710 mm LG (W56) 8121-2291a

with ends labeled

‘806’ and ‘726’

1 Cable Assembly, Coaxial 570 mm LG (W53) 8121-2292a

with ends labeled

‘901’ and ‘101’

1 Screw, M3 x 0.5 (8 mm long) 0515-0372

6 Screw, M3 x 0.5 (6 mm long) flathead 0515-1227

15 Cable Tie 1400-0249

1 Coaxial Cable Clip 5041-9690

1 Entitlement Certificate 5964-5178

1 Entitlement Certificate Envelope 5967-7169

1 Installation Note This note

6Installation Note N9020-90239

Option HLB, 40 MHz to 85 MHz Analysis Bandwidth Upgrade Serial Prefix <MY/SG/US5233

Tools Required

•T-10TORXDriver

•T-20TORXDriver

• 5/16-inch torque wrench

• 9/16-inch nut driver

• 1/4-inch socket on 4-pound torque wrench

• Scissors or knife

• Diagonal cutters

• Agilent Calibration and Adjustment Software, N7814A (revision E.11.00 or later)

• Test equipment and computer supported by the X-Series Performance Tests and Adjustment

Software

• MXA Signal Analyzer Service Guide. This manual is available as:

— N9020A Option 0BW or p/n N9020-90218

• Microsoft Windows based personal computer with internet access and USB port

• USB storage device with >2GB free memory

Initial Instrument Functionality Check

Power on the instrument and allow the instrument to boot up. Run an alignment and display the

measurement screen. (The instrument will probably display a spectrum analyzer screen and you will

see the instrument sweeping.)

There should be no alignment failures. If there are failures, investigate and fix the problem before

continuing.

WARNING Before you disassemble the instrument, turn the power switch to Standby.

After the instrument has completely shut down, unplug the instrument.

Failure to unplug the instrument can result in personal injury.

CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All

work on electronic assemblies should be performed at a static-safe workstation.

Refer to the documentation that pertains to your instrument for information about

static-safe workstations and ordering static-safe accessories.

Installation Note N9020-90239 7

Installation Procedure

Analyzer Information

1. Connect a power cord to the analyzer and turn on the analyzer.

2. After the analyzer has completed turning on, press System, Show, System. Make note of the

following information from the Show System screen:

Product Number ________________

Serial Number ________________

Instrument S/W Revision ________________

3. Check for the presence of the options listed below in the Show System screen. Put a check mark or

“X” after each option listed below that appears in the Show System menu.

N9020A-B40 ______

N9020A-DP2 ______

N9020A-MPB ______

N9020A-BBA ______

N9020A-508 ______

N9020A-513 ______

N9020A-526 ______

4. Refer to the data in step 2 above. If the Product Number is not N9020A, do not proceed with the

installation of this kit. This kit is to be installed only on N9020A signal analyzers.

5. Refer to the data in step 2 above. If the Serial Number prefix (the first six characters of the serial

number) is not earlier than MY5233, SG5233, or US5233 do not proceed with the installation of

this kit. This kit is to be installed only on N9020A signal analyzers with earlier serial numbers.

6. Refer to the data in step 3 above. If option N9020A-BBA is present, do not proceed with the

installation of this kit. MXA signal analyzers with Option BBA do not have sufficient room to

install the two additional boards required for analysis bandwidths of 85 MHz and wider.

7. Refer to the data in step 3 above. If neither Options N9020A-B40, N9020A-MPB, or

N9020A-DP2 are not already present, do not proceed with the installation of this kit. One of two

different kits is available for this situation. Refer to www.agilent.com/find/mxa_upgrades.

8. Refer to the data in step 3 above. If option N9020A-B40 is not already present but either

N9020A-DP2 and/or N9020A-MPB are present, an additional upgrade kit, N9020AK-B40 will

also need to be installed to upgrade the analysis bandwidth to 40 MHz. This 40 MHz analysis

bandwidth upgrade should be performed prior to installing this 40 MHz to 85 MHz analysis

bandwidth upgrade kit.

9. Refer to the data in step 3 above. If Option N9020A-MPB is not already present and either

frequency range option N9020A-508, N9020A-513, or N9020A-526 is present, it will be necessary

to upgrade the analyzer to add option N9020A-MPB before installing this kit. Refer to

www.agilent.com/find/mxa_upgrades for details on how to upgrade to N9020A-MPB.

8Installation Note N9020-90239

Installation Procedure

Update Instrument Software

Updating the instrument software and installing the necessary licenses before installing the new

hardware will help ensure that the hardware installation was successful.

NOTE The minimum instrument software version is A.13.15.

Go to the following website and determine whether or not the analyzer has the latest instrument

software already installed:

http://www.agilent.com/find/xseries_software

If the analyzer does not have the latest instrument software already installed, download and install the

latest version.

Installation Note N9020-90239 9

Installation Procedure

Licensing the New Options

NOTE If N9020AK-BU4, Analysis Bandwidth Upgrade, 85 MHz to 125 MHz,

N9020AK-BU5, Analysis Bandwidth Upgrade, 85 MHz to 160 MHz, or

N9020AK-B40, Analysis Bandwidth Upgrade, 40 MHz will also be installed, the

licenses provided by these kits should be installed at this time.

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB Storage Device.

6. Connect the USB Storage Device to one of the analyzer’s USB ports. Connect a mouse to another

USB port. Windows will detect the new hardware and may display the configuration menu shown

in Figure 1. This menu may be configured according to your preferences.

Figure 1 USB Storage Device Configuration Menu

10 Installation Note N9020-90239

Installation Procedure

7. The signal analyzer will automatically consume the License File. (This may take a few minutes)

When the License File is consumed the Agilent License Manager will display a “Successful

License Installation” message as shown in Figure 2. Since the license file contains multiple

licenses, multiple “Successful License Installation” messages will appear. Wait until all licenses

have been consumed before removing the USB Storage Device.

Figure 2 Successful License Installation

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight N777 C Series Betriebsanleitung

Keysight

Keysight N9000A Bedienungsanleitung

Keysight

Keysight B1500A Series Bedienungsanleitung

Keysight

Keysight E5061B Bedienungsanleitung

Keysight

Keysight E5081A ENA-X Series Benutzerhandbuch

Keysight

Keysight MXA Series Installations- und Betriebshandbuch

Keysight

Keysight PNA-X N5241A Bedienungsanleitung

Keysight

Keysight M9217A PXIe 2-CH Benutzerhandbuch

Keysight

Keysight 16192A Bedienungsanleitung

Keysight

Keysight M9202A Benutzerhandbuch

Keysight

Keysight U8903B Bedienungsanleitung

Keysight

Keysight PNA E8362C Bedienungsanleitung

Keysight

Keysight u2722a Bedienungsanleitung

Keysight

Keysight N5244/45AS Option H85 Handbuch

Keysight

Keysight 53147A Betriebsanleitung

Keysight

Keysight M9703A Series Kurzanleitung

Keysight

Keysight N2820A Bedienungsanleitung

Keysight

Keysight 34420A Bedienungsanleitung

Keysight

Keysight InfiniiMax III N2800A Series Bedienungsanleitung

Keysight

Keysight x series Kurzanleitung

Keysight

Keysight N9342CN Bedienungsanleitung

Keysight

Keysight N2790A Bedienungsanleitung

Keysight

Keysight M9603A PXIe Bedienerhandbuch

Keysight

Keysight N437 Series Handbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung