Keysight N9030B Installations- und Betriebshandbuch

Option YAV

Y-Axis Video Out

Keysight N9030B PXA Signal Analyzer

Installation Note

Notices

The information contained in this document is subject to change without notice.

Keysight Technologies makes no warranty of any kind with regard to this material, including but

not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Keysight Technologies shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of this material.

Manual Part Number

N9030-90086

Edition

Edition 1, February 2016

Printed in USA/Malaysia

Published by:

Keysight Technologies, Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403

Installation Note N9030-90086 3

Option YAV Installation Kit

Products Affected: N9030B PXA Signal Analyzer

Serial Numbers: All

Options

To Be Performed By: (X) Keysight Service Center

(X) Personnel Qualified by Keysight

(X) Customer

Estimated Installation Time:

Estimated Adjustment and Verification Time:

0.5 Hours

4Installation Note N9030-90086

Option YAV Installation Kit

Introduction

This kit contains all of the instructions required to install Option YAV on a Keysight N9030B PXA

signal analyzer. Option YAV enables the ANALOG OUT port and provides various signal selections.

The rear panel ANALOG OUT port is present on all PXA signal analyzers, however Option YAV must

be enabled via a license file.

Contents

1. At the time of manufacture the hardware related to this option was fully

adjusted and the option performance was verified to be within its

warranted specifications. Within one year of the initial calibration date

of the instrument this option is fully calibrated with no further

adjustment or verification testing.

To determine the initial calibration date, locate the original calibration

certificate that was shipped with the instrument at the time of

purchase. The Date of Calibration is printed on the original calibration

certificate.

To ensure that this newly installed option has been installed properly,

the procedure that follows includes a functional check.

2. The latest revision of the X-Series signal analyzer software may be

downloaded from:

http://www.keysight.com/find/Xseries_software

3. This option is licensed for one instrument model/serial number

combination. The license key will only install on the designated

instrument.

Quantity Description Keysight Part

Number

1 Installation Note This note

1 Option Upgrade Entitlement Certificate 5964-5178

Installation Note N9030-90086 5

Option YAV Installation Kit

Tools Required for Installation

— Personal computer with internet access and USB port

— USB storage device with > 2 GB free memory

Tools Required for Manual Operation Verification

— Voltmeter

— Test cable, BNC (used to connect voltmeter to the analyzer rear panel ANALOG OUT)

— Banana plug to BNC adapter (used to connect voltmeter to BNC cable)

Installation Procedure over USB

1. Locate the Option Upgrade Entitlement Certificate (5964-5178) from the kit.

2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the

Certificate.

3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an

attached License File.

4. Locate a USB storage device. Perform a virus scan on this device before use.

5. Save the License File to the root directory of the USB Storage Device.

6. Connect the USB Storage Device to the signal analyzer USB port. Windows will detect the new

hardware and may display the configuration menu shown in Figure 1. This menu may be

configured according to your preferences.

Figure 1 USB Storage Device Configuration Menu

6Installation Note N9030-90086

Option YAV Installation Kit

7. The signal analyzer will automatically consume the License File. (This may take a few minutes)

When the License File is consumed the Keysight License Manager will display a “Successful

License Installation” message similar to the one shown in Figure 2.

Figure 2 Successful License Installation

Alternate Installation Procedure

The License File can be manually installed over USB or LAN by placing the license file in the

following folder on the signal analyzer

C:\Program Files\Agilent\licensing

Verify the Installation

1. Cycle the power on the signal analyzer.

2. Press System, Show System to display a list of installed options.

3. Verify that the newly installed option appears on the list.

Installation Note N9030-90086 7

Option YAV Installation Kit

Manually Verify Operation

1. Preset X-Series analyzer. Assure mode is Spectrum Analyzer.

2. Display the 50 MHz calibrator signal. Press Input/Output, RF Calibrator, 50 MHz. Press FREQ,

Center Frequency, key in 50 MHz. Press Span, Zero Span. You should see a flat line across the

display at −25 dBm.

3. Press AMPTD, Ref Level, and key in −25 dBm. The displayed signal level should be at the top

graticule line.

4. Press Input/Output, Output, Analog Out, Screen Video.

5. Connect a voltmeter, set to measure DC volts, to the analyzer rear panel ANALOG OUT

connector.

6. The voltmeter should measure 1V.

7. Increase the Ref Level to −15 dBm. The signal should drop one graticule division on screen and

the voltmeter reading should be 0.9 V.

8. This test is sufficient to determine if the output circuitry is working properly for all Analog Out

signal selections.

8Installation Note N9030-90086

Option YAV Installation Kit

Utilities, Adjustments, and Performance Verification Tests

Calibration Software and specified test equipment is required to perform the adjustments, and can

be used to automate the performance verification testing. Information on how to obtain this

software can be found at

http://www.keysight.com/find/calibrationsoftware

Utilities Required

None

Adjustments Required

None

Performance Testing Required

None

A full calibration is required to assure the instrument meets all specifications

The end user must ultimately determine whether they want a full calibration to be performed after

the installation of this upgrade or not. If a full calibration is required, arrangements regarding the

level of calibration must be made between the end user and the calibration provider.

For assistance, contact your nearest Keysight Technologies Sales and Service Office. To find your

local Keysight office access the following URL, or if in the United States, call the following

telephone number:

http://www.keysight.com/find/assist

1-800-829-4444 (8 am - 8 pm ET, Monday - Friday)

This information is subject to change

without notice.

Edition 1, February 2016

N9030-90086

www.keysight.com

Andere Handbücher für N9030B

Inhaltsverzeichnis

Andere Keysight Messgerät Handbücher

Keysight

Keysight N5241BU-229 Bedienungsanleitung

Keysight

Keysight U1211A Handbuch

Keysight

Keysight x series Bedienungsanleitung

Keysight

Keysight E5052B Bedienungsanleitung

Keysight

Keysight U1732C Bedienungsanleitung

Keysight

Keysight 34450A Bedienungsanleitung

Keysight

Keysight N9010B Bedienungsanleitung

Keysight

Keysight 42941A Bedienungsanleitung

Keysight

Keysight M9370A Benutzerhandbuch

Keysight

Keysight U1242C Bedienungsanleitung

Keysight

Keysight N5241AU- 927 Installations- und Betriebshandbuch

Keysight

Keysight N5244AU-940 Bedienungsanleitung

Keysight

Keysight M9601A Bedienerhandbuch

Keysight

Keysight MXA Series Installations- und Betriebshandbuch

Keysight

Keysight N5227BU-420 Bedienungsanleitung

Keysight

Keysight 478A Service-Handbuch

Keysight

Keysight N9912A Bedienungsanleitung

Keysight

Keysight N9320B Handbuch

Keysight

Keysight N9030A-503 Bedienungsanleitung

Keysight

Keysight U8903A Bedienungsanleitung

Keysight

Keysight E5063A Bedienungsanleitung

Keysight

Keysight M9290A Bedienungsanleitung

Keysight

Keysight u1701b Handbuch

Keysight

Keysight PXA N9030A Installations- und Betriebshandbuch

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

ADTEK

ADTEK MW-5 Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung