Kichler Lighting Spyn Bedienungsanleitung

52" Spyn LED

TABLE OF CONTENTS

SAFETY RULES ………………………………………………………. 4

TOOLS REQUIRED ……………………………………………… 5

PACKAGE CONTENTS …………………………………………. 5

MOUNTING OPTIONS ………………………………………… 6

HANGING THE FAN ………………………………………....... 7

INSTALLATION OF SAFETY SUPPORT ……………… 9

ELECTRICAL CONNECTIONS …………………………… 10

FINISHING THE INSTALLATION ……………………….. 11

ATTACHING THE FAN BLADES …………………………… 12

INSTALLING SWITCH HOUSING ………………………… 12

INSTALLING THE LIGHT KIT ………………………………… 13

INSTALLING THE WALL CONTROL …………………… 15

OPERATING INSTRUCTIONS ……………………………… 16

TROUBLESHOOTING …………………………………………… 17

52" Spyn LED

8. Do not use water or detergents when cleaning the fan or fan

blades. A dry dust cloth or lightly dampened cloth will be suitable

for most cleaning.

9. After making the electrical connections, spliced conductors

should be turned upward and pushed carefully up into outlet box.

The wires should be spread apart with the ground wire and white

(common) wire to one side with the black (load) wire to the other

side of the outlet box.

10. Electrical diagrams are reference only.Light kits that are not

packed with the fan must be ETL Listed and marked suitable

for use with the model fan you are installing. Switches must

be ETL General Use Switches. Refer to the Instructions

packaged with the light kits and switches for proper assembly.

SAFETY RULES

1. To reduce the risk of electric shock, insure electricity has

been turned o at the circuit breaker or fuse box before

beginning.

2. All wiring must be in accordance with the National

Electrical Code and local electrical codes. Electrical

installation should be performed by a qualified licensed

electrician.

3. WARNING: To reduce the risk of fire or electric shock, use

only the control provided with the fan.

4. WARNING: To reduce the risk of personal injury, use

only the two steel screws (and lock washers) provided

with the outlet box for mounting to the outlet box. Most

outlet boxes commonly used for the support of lighting

fixtures are not acceptable for fan support and may

need to be replaced,consult a qualified electrician if in

doubt.

5. To operate the reverse function on this fan, slide the reverse

switch to the opposite position.

6. Avoid placing objects in the path of the blades.

7. To avoid personal injury or damage to the fan and other

items, be cautious when working around or cleaning the

fan.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT

BEND THE BLADE BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER INSTALLATION.

DO NOT INSERT OBJECTS IN THE PATH OF THE BLADES.

PACKAGE CONTENTS

Unpack your fan and check the contents . You should have the following items:

A. Mounting bracket

B. Ball / downrod assembly

C. Canopy

D. Canopy Hole Cover

E. Coupling Cover

F. Motor Body

G. Fan Blade (3)

H .Switch Housing

I. Light Kit

J. Shade

Phillips screwdriver

Blade screwdriver

11 mm wrench

Step ladder

Wire cutters

TOOLS REQUIRED

K. Wall Control System

L. Package hardware

1) Mounting hardware :

Wood screw (2) ,Flat Washer (2) , Screw (2) ,

Lock washer (2), Wire Connector (3)

2) Blade attachment hardware :

Screws (8) , Washers (8)

3) Safety cable hardware :

Wood screw (1) ,Spring washer (1),

Flat washer (1)

4) Balance kit

52" Spyn LED

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation) listed

mounting box, then read the following instructions. Disconnect the

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box and its

support must be able to fully support the moving weight of the fan

(at least 50 lbs). Do not use plastic outlet boxes.

box.

NOTE: If you are installing the ceiling fan on a sloped (vaulted)

ceiling, you may need a longer downrod to maintain proper

clearance between the tip of the blade and the ceiling. A minimum

clearance of 12” is suggested for optimal operation.

NOTE: Depending on the location you have selected for installation,

you may need to purchase and install a “Joist Hanger” for the

support of the outlet box. Make sure the joist hanger you purchase

has been designed for use with ceiling fans. (Fig. 4)

Fig. 1

Outlet box

Fig. 2

Provide strong

support

Recessed

outlet box Ceiling

mounting

plane

Fig. 3

ANGLED CEILING

MAXIMUM 20° ANGLE

Outlet box

Fig. 4

HANGING THE FAN

REMEMBER to turn o the power before you begin installation. This is necessary

for your safety and also the proper programming of the control system.To properly

install your ceiling fan, follow the steps below.

Step 1 . Before attaching fan to outlet box (not included), ensure the outlet box is

securely fastened to at least two points to a structural ceiling member (a loose box

will cause the fan to wobble). Pass the 120 volt supply wires from the ceiling outlet

box through the center of the ceiling mounting bracket. Install mounting bracket to

outlet box in ceiling using the screws and washers included with the outlet box or

screws and washers in the hardware bag. (Fig. 5)

Step 2. Remove the hanger ball from downrod assembly by loosening set screws ,

removing the cross pin, and sliding ball o the rod.( Fig. 6)

Fig. 5

Outlet Box

Flat Washer

Screw

Mounting

Bracket

Fig. 6

Downrod

Cross Pin Set Screw

Hanger Ball

52" Spyn LED

Step 5

WARNING:

. Now lift the motor body into position and place the hanger ball into the mounting

bracket. Rotate until the "Check Tab" has dropped into the "Registration Slot " and

seats ﬁrmly. ( Fig. 9) The entire motor body should not rotate if this is done correctly.

Failure to properly seat the "Check Tab" can damage the ceiling fan during

operation.

HANGING THE FAN

Step 4. Slip the coupling cover, canopy hole cover and canopy onto the downrod.

Carefully reinstall the hanger ball onto the downrod . Make sure the cross pin is in

the correct position and the set screw is tight and the wires are not twisted . ( Fig. 8)

Step 3. Loosen the two set screws and remove the clip and cross pin from the top

coupling of the motor body.Carefully feed the fan wires and safety cable up through

the downrod. Thread the downrod onto the motor coupling until the cross pin holes

are aligned. Next, replace the cross pin and clip, and tighten both set screws. (Fig. 7)

Fig. 7

Fig. 8

Fig. 9

Set Screw

Downrod

Clip

Set Screw

Cross Pin

Motor Body

Clip Cross Pin

Canopy

Cherk Tab

Registration Slot

Hanger Ball

Mounting Bracket

Canopy Hole Cover

Coupling Cover

Step 1.

NOTE:

INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

A safety support cable is provided to help prevent the ceiling fan from faIling, please

install it as follows.

Drive a wood screw and washers into the side of the brace that holds the outlet

box. Leave 3mm (1/8") of space between the support brace and the washer. (Fig. 10)

Insert the safety cable through the mounting bracket and one of the holes in the

outlet box into the ceiling. Adjust the length of the safety cable to reach the screw and

washers by pulling the extra cable through the cable clamp until the overall length is

correct, put the end of the cable back through the cable clamp, forming a loop at the

end of the cable. Tighten the cable clamp securely. Now, put the loop in the end of the

safety cable over the wood screw and under the washer. Tighten the wood screw

securely. (Fig. 11)

Although the safety support cable is required for Canadian installations only.

It’s a good idea to make the attachment with any installation.

Step 2.

Fig. 10

Flat Washer

Wood Screw

Spring Washer

Outlet Box

Support Brace

Ceiling

Fig. 11

Safety Cable Bolt

Wood Screw

52" Spyn LED

MAKE THE ELECTRICAL CONNECTIONS

WARNING: To avoid possible electrical shock, be sure you have turned o the power

at the main circuit panel before wiring. Follow the steps below to connect the fan to

your household wiring. Use the wire connectors supplied with your fan. Secure the

connector with electrical tape. Make sure there are no loose wire stands or connections.

WARNING: If your house wires are dierent colors other than referenced in this manual,

stop immediately. A professional electrician is recommended to determine proper wiring.

Step 1. Connect the BLACK wire from the fan to BLACK wire marked “TO MOTOR L”

from the wall control. (Fig.12)

Step 2. Connect the BLUE wire from the fan to BLUE wire marked “FOR LIGHT” from

the wall control.(Fig.12)

Step 3. Connect the WHITE wire from the fan to the household neutral WHITE wire.(Fig. 12)

Step 4. Connect the BLACK with WHITE stripes wire marked “AC IN L” from the wall control

to the household BLACK/WHITE supply wire.(Fig. 12)

Step 5. Connect GROUND(GREEN) wires from mounting bracket and downrod ball and wall

control, to GROUND(GREEN) or BARE(COPPER) wire from house.(Fig.12)

Step 6. Secure the wire connection with plastic connectors provided. After connecting the

wires, spread them apart so that the green and white wires are on one side of the outlet box.

black and white stripes wire and blue wire are on the other side. (Fig. 12)

NOTE: Carefully tuck the wire connections up into the outlet box.

Fig. 12

Ground wire

White (Neutral)

Black (motor)

Black ("TO MOTOR L")

Blue(for light)

AC IN N( White)

B/W ("AC" IN L")

Green or bare copper (ground)

AC IN L(Black/white)

Ground/Earth

Wall Control

Blue( light)

Inhaltsverzeichnis

Sprachen:

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting LYNDON Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lucian II 330241 Bedienungsanleitung

Kichler Lighting

Kichler Lighting ZEUS KLF-ZEUS-60-WHT-BN Bedienungsanleitung

Kichler Lighting

Kichler Lighting Decor Kimberley Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lyndon 300120 Bedienungsanleitung

Kichler Lighting

Kichler Lighting ELLYS Bedienungsanleitung

Kichler Lighting

Kichler Lighting Cadence Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35153 Handbuch

Kichler Lighting

Kichler Lighting 35152 Bedienungsanleitung

Kichler Lighting

Kichler Lighting KOSMUS Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300044 Bedienungsanleitung

Kichler Lighting

Kichler Lighting BASICS PRO SELECT 330017MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Lacey Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield Select Bedienungsanleitung

Kichler Lighting

Kichler Lighting Eads 310135 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Cottage Grove Bedienungsanleitung

Kichler Lighting

Kichler Lighting Larissa Bedienungsanleitung

Kichler Lighting

Kichler Lighting Select Canfield 300107 Bedienungsanleitung

Kichler Lighting

Kichler Lighting FRYST Bedienungsanleitung

Kichler Lighting

Kichler Lighting Ample Bedienungsanleitung

Kichler Lighting

Kichler Lighting 330015WH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Emerson HIGH COUNTRY Bedienungsanleitung

Kichler Lighting

Kichler Lighting Kevlar 310150WCP Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35156 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung