Kichler Lighting Lyndon 300120 Bedienungsanleitung

Kichler®Lighting

7711 East Pleasant Valley Road

P.O. Box 318010

Cleveland, Ohio 44131-8010

Customer Service

866.558.5706

8:30 AM to 5:00 PM EST,

Monday - Friday

Instruction Manual

LyndonTM

A Kichler

Decor

™

ceiling fan

Includes our new

CoolTouch Control System

Looks permanent, but goes wherever you go!

U.S. Patent Pending

300120

3066708

1. To reduce the risk of electric shock, insure

electricity has been turned off at the circuit

breaker or fuse box before beginning.

2. All wiring must be in accordance with the

National Electrical Code and local

electrical codes. Electrical installation

should be performed by a qualiﬁed

licensed electrician.

3. WARNING: Suitable for use with solid-

state speed controls.

4. WARNING: To reduce the risk of personal

injury, use only the two steel screws (and

lock washers) provided with the outlet box

for mounting to the outlet box. Most outlet

boxes commonly used for the support of

lighting ﬁxtures are not acceptable for fan

support and may need to be replaced,

consult a qualiﬁed electrician if in doubt.

5. The outlet box and support structure must

be securely mounted and capable of

reliably supporting a minimum of 50

pounds. Use only ETL Listed outlet boxes

marked "FOR FAN SUPPORT".

6. The fan must be mounted with a minimum

of 7 feet clearance from the trailing edge of

the blades to the ﬂoor.

7. To operate the reverse function on this

fan, press the reverse button while the fan

is running.

8. Avoid placing objects in the path of the

blades.

9. To avoid personal injury or damage to the

fan and other items, be cautious when

working around or cleaning the fan.

10. Do not use water or detergents when

cleaning the fan or fan blades. A dry dust

cloth or lightly dampened cloth will be

suitable for most cleaning.

11. After making the electrical connections,

spliced conductors should be turned

upward and pushed carefully up into

outlet box. The wires should be spread

apart with the ground wire and white

(common) wire to one side with the black

(load) wire to the other side of the outlet

box.

12. Electrical diagrams are reference only.

Light kits that are not packed with the fan

must be ETL Listed and marked suitable

for use with the model fan you are

installing. Switches must be ETL General

Use Switches. Refer to the Instructions

packaged with the light kits and switches

for proper assembly.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR PERSONAL INJURY, MOUNT

FAN TO OUTLET BOX MARKED

"ACCEPTABLE FOR FAN SUPPORT".

WARNING

TO REDUCE THE RISK OF PERSONAL

INJURY, DO NOT BEND THE BLADE

BRACKETS (ALSO REFERRED TO AS

FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS

IN THE PATH OF THE BLADES.

1. SAFETY RULES

Special Notice

This appliance is equipped with a "Wattage

Limiting Device" required by the United

States Department of Energy. The device

has been installed at the factory and can

not be removed.

Installing Lamps in excess of 190 total

watts will disable the unit's light ﬁxture. If

this should happen, you will need to reset

the lighting ﬁxture by turning the power off

to the ceiling fan and/or light ﬁxture,

reinstalling lamps totaling less that 190

watts and then turning the power back on.

3. PACKAGE CONTENTS

Unpack your fan and check the contents .

You should have the following items:

a. Mounting bracket

b. Ball / downrod assembly (1)

c. Canopy

d. Canopy Hole Cover

e. Coupling cover

f. Motor Body

g. Mounting Plate

h. Light Kit

i. Fan Blades (5)

j. Set of 5 blades arm and pre-installed

mounting screws

k. Fan Lamp (3)

l. Glass Shade

n. Package hardware

m. Cool Touch TM Control System

1) Mounting hardware:

wood screws (2), ﬂat washers (2),

screws (2) , Spring washers (2),

wire nuts (3)

2) Blade attachment hardware:

screws (17),

ﬁber washers (17)

3) Blade arm hardware :

Screw (2)

4) Safety cable hardware :

Wood screw (1) , spring washer (1),

ﬂat washer (1)

Slip resistant sleeve (3)

5) Balance kit

6) Slip resistant sleeve hardware:

Screw (3)

7) Screw hardware:

Philips screw driver

Blade screw driver

11 mm wrench

Step ladder

Wire cutters

2. TOOLS AND MATERIALS REQUIRED

LyndonTM

4. MOUNTING OPTIONS

Outlet box

Provide strong

support

Recessed

outlet box Ceiling

mounting

plate

Outlet box

Fig. 1

Fig. 3

Fig. 4

Outlet box

Fig. 2

ANGLED CEILING

MAXIMUM 30°ANGLE

If there isn't an existing ETL listed mounting

box, then read the following instructions.

Disconnect the power by removing fuses or

turning off circuit breakers.

Secure the outlet box directly to the building

structure. Use appropriate fasteners and

building materials. The outlet box and its

support must be able to fully support the

moving weight of the fan (at least 50 lbs). Do

not use plastic outlet boxes.

Figures 1, 2 and 3 are examples of different

ways to mount the outlet box.

NOTE: If you are installing the ceiling fan on a

sloped (vaulted) ceiling, you may need a

longer downrod to maintain proper clearance

between the tip of the blade and the ceiling.

A minimum clearance of 12" is suggested for

optimal operation.

NOTE: Depending on the location you have

selected for installation, you may need to

purchase and install a "Joist Hanger" for the

support of the outlet box. Make sure the joist

hanger you purchase has been designed for

use with ceiling fans. (Fig. 4)

5. HANGING THE FAN

REMEMBER to turn off the power before you

begin installation. This is necessary for your

safety and also the proper programming of the

control system.

To properly install your ceiling fan, follow the

steps below.

Step 1. Before attaching fan to outlet box

(not included), ensure the outlet box is securely

fastened to at least two points to a structural

ceiling member (a loose box will cause the fan

to wobble). Pass the 120 volt supply wires from

the ceiling outlet box through the center of the

ceiling mounting bracket. Install mounting

bracket to outlet box in ceiling using the screws

and washers included with the outlet box or

screws and washers in the hardware bag.

(Fig. 5)

Step 4. Slip the coupling cover, canopy hole cover

and canopy onto the downrod. Carefully reinstall

the hanger ball onto the downrod . Make sure the

cross pin is in the correct position and the set

screws are tight and the wires are not twisted .

( Fig. 8)

Step 2. Remove the hanger ball from downrod

assembly by loosening set screws , removing

the cross pin, and sliding ball off the rod. ( Fig. 6)

Step 3. Loosen the two set screws and remove

the clip and cross pin from the top coupling of

the motor body.

Carefully feed the fan wires up through the

downrod. Thread the downrod onto the motor

coupling until the cross pin holes are aligned.

Next, replace the cross pin and clip, and tighten

both set screws. (Fig. 7)

LyndonTM

Flat Washer

Screw

Fig. 5

Ceiling Mounting Bracket

ETL Listed Outlet Box

Screw

Downrod

Flat Washer

Fig. 6

Set Screw

Hanger Ball

Cross Pin

Clip

Set Screw

Fig. 7

Motor Body

Cross Pin

Clip

Set Screw

Fig. 8

Canopy

Canopy Hole Cover

Coupling Cover

Motor Body

Set Screw

Step 5. Now lift the motor body into position

and place the hanger ball into the hanger bracket.

Rotate until the "Check Tab" has dropped into

the "Registration Slot " and seats ﬁrmly. ( Fig. 9)

The entire motor body should not rotate is this is

done correctly.

6 . INSTALLATION OF SAFETY SUPPORT

(required for Canadian installation ONLY)

WARNING: Failure to properly seat the "Check

Tab" can damage the ceiling fan during operation.

A safety support cable is provided to help prevent

the ceiling fan from failing, please install it as

follows.

Step 1. Drive a wood screw and washers into the

side of the brace that holds the outlet box. Leave

3mm (1/8") of space between the support brace

and the washer. (Fig. 10)

NOTE: Although the safety support cable is

required for Canadian installations only. It’s a good

idea to make the attachment with any installation.

Step 2. Insert the safety cable through the

mounting bracket and one of the holes in the

outlet box into the ceiling. Adjust the length of the

safety cable to reach the screw and washers by

pulling the extra cable through the cable clamp

until the overall lenght is correct, put the end of the

cable back through the cabel clamp, forming a

loop at the end of the cable. Tighten the cable

clamp securely. Now, put the loop in the end of the

safety cabel over the wood screw and under the

washer. Tighten the wood screw securely. (Fig. 11)

Check Tab Registration Slot

Fig. 9

Safety CableBolt

Wood Screw

Fig. 11

Flat Washer

Wood Screw

Spring Washer

Outlet Box

Support Brace

Ceiling

Fig. 10

7. MAKE THE ELCTRIC CONNECTIONS

WARNING: To avoid possible electrical shock,

be sure you have turned off the power at the

main circuit panel before wiring.

WARNING: If your house wires are different

colors than referenced in this manual, stop

immediately. A professional electrician is

recommended to determine proper wiring.

Step 1. Insert the receiver into the mounting

bracket, and keep ﬂat in opposition of ceiling.

(Fig. 13)

Step 2. Motor to Receiver Electrical Connections:

Connect the BLACK wire from the fan to BLACK

wire marked "TO MOTOT L" from the receiver.

Connect the WHITE wire from the fan to the

WHITE wire marked "TO MOTOR N" from the

receiver. Connect the BLUE wire from the fan to

the BLUE wire marked "FOR LIGHT " from the

receiver. Secure all the wire connections with the

plastic wire nuts provided. ( Fig. 14)

Follow the steps below to connect the fan to

your household wiring. Use the wire

connecting nuts supplied with your fan. Secure

the connector with electrical tape. Make sure

there are no loose wire stands or connections.

LyndonTM

Fig. 12

ON ECE

Battery Compartment

Code Switch

Fig. 13

Mounting Bracket

Receiver

White (Neutral)

Blue(FOR LIGHT) Ground wire

White("AC IN N")

White("TO MOTOR N")

Green or bare copper (ground)

Black (motor)

Blue(for light)

Black ("TO MOTOR L")

Receiver

Black("AC" IN L")

Black (hot)

Outlex box

White (Neutral)

Fig. 14

NOTE: The CoolTouch Control System is

equipped with 16 code combinations to prevent

possible interference from or to other remote

units. The frequency switches on your receiver

and transmitter have been preset at the factory.

Please recheck to make sure the switches on

the transmitter and receiver are set to the same

position, any combination of settings will

operate the fan as long as the transmitter and

receiver are set to the same opposition.

( Fig. 12) Chainging the orfer of switches on

each switch block, changes the operational

frequency.

Step 3. Remote Receiver to Outlet Box Electrical

Connections: Connect the BLACK (hot) wire from

the ceiling to the BLACK wire marked “AC in L”

from the receiver . Connect the WHITE ( neutral )

wire from the ceiling to the WHITE wire marked

“ AC in N” from the Receiver . Secure the wire

connections with the plastic wire nuts provided .

( Fig. 14)

Step 4. If your outlet box has a ground wire

( green or bare copper ) connect it to the fan

ground wires : otherwise connect the hanging

bracket ground wire to the mounting bracket.

Secure the wire connection with a plastic nut

provided. After connecting the wires, spread them

apart so that the green and white wires are on one

side of the outlet box and black and blue wires

are on the other side. ( Fig. 14)

NOTE: Carefully tuck the wire connections up

into the outlet box

NOTE: Fan must be installed at a maximum

distance of 30 feet from the transmitting unit for

proper signal transmission between the

transmitting unit and the fan’s receiving unit.

Step 1. Remove one of the two shoulder screws

in the mounting bracket. Loosen the second

shoulder screw without fully removing it.

(Fig. 15)

Step 2. Assemble canopy by rotating key slot in

canopy over shoulder screw in mounting bracket.

Tighten shoulder screw. Fully assemble and

tighten second shoulder screw that was

previously removed. (Fig. 16)

8 . FINISHING THE INSTALLATION

Shoulder Screw

Mounting Bracket

Fig. 15

Canopy

Fig. 16

Shoulder Screw

LyndonTM

9. ATTACHING THE FAN BLADES

Step 3. Securely attach and tighten the canopy

hole cover over the shoulder screws in the

mounting bracket utilizing the keyslot twist-lock

feature. (Fig. 17)

NOTE: Before continuing , make sure the power

is disconnected by turning off the circuit breaker

of removing the fuse at the circuit box.

Step 1. Position the blade over the blade arm

with threaded posts showing. Make sure the

bottom edge of the blade is fully seated against

the blade arm. With a Philips screwdrivr, start a

screw into the blade arm (do not tighten) and

repeat for the 2 remaining blade screws and ﬁber

washers. Tighten each screw securely starting

with the center screw. Make sure the blade is

straight. Repeat steps for the remaining blades.

(Fig. 18)

Step 2. Fasten blade assembly to the holes

located on the bottom of the ﬂywheel. Tighten the

two "pre- installed" motor screws in the blade

arm. Repeat steps for the remaining blades

assemblies. (Fig. 19)

Canopy Hole Cover

Fig. 17

Shoulder Screw

Blade

Blade Screw

Fiber Washer

Blade Arm

Fig. 18

Flywheel

Blade Arm

Motor Screw

Motor Body

Fig. 19

10. INSTALLING THE MOUNTING PLATE

Step 1. You will ﬁnd one red label on the mounting

ring. Remove this screw (near the red dot label)

preinstalled on mounting ring and loosen the other

two (do not remove). Align the red dot labels on

the mounting ring and mounting plate. Attach the

mounting plate to the mounting ring with the 2

screws drop into the two slot holes on the mounting

plate. Please adjust the mounting plate if necessary,

to line up the rim both on the motor body and

mounting plate. Securely by tightening the 2 screws

previously loosened and the one previously

removed. (Fig. 20)

11. INSTALLING THE LIGHT KIT

NOTE: Before continuing installation, conﬁrm that

the power is still turned off at the main circuit

breaker or by removing the correct fuse. Turning

the power off using a wall switch is not sufﬁcient to

prevent electrical stock.

Step1. Remove 1 of the 3 screws from the

mounting plate and loosen the other 2 screws

(do not remove). (Fig. 21)

Step 2. Hold the light kit close to the mounting

plate and connect the WHITE wires from the

mounting plate and fan by pushing the connectors

together. Follow the same procedure with the

BLACK wires. (Fig. 21)

Step 3. Tuck the connections neatly into the light

kit. Align the key holes on the light kit with the 2

screws on the mounting plate. Turn the ligh kit until

it locks in place at the narrow end of the key holes.

Securely by tighten all three screws. (Fig. 21)

Mounting Ring

Mounting Plate

Screw

Fig. 20

Mounting Plate

Light Kit

Screw

Wiring Connector

Fig. 21

12. INSTALLING THE LAMP AND GLASS

SHAD

Step 1. Install the 3, 40 Watt/B10 incandescent

lamps (provided). (Fig. 22)

Light Kit

Fig. 22

Inhaltsverzeichnis

Andere Kichler Lighting Lüfter Handbücher

Kichler Lighting

Kichler Lighting Select Dorset Bedienungsanleitung

Kichler Lighting

Kichler Lighting Saxon Premier Bedienungsanleitung

Kichler Lighting

Kichler Lighting Grace 300316 Bedienungsanleitung

Kichler Lighting

Kichler Lighting KLF-SOLA-34-WHT-BN Bedienungsanleitung

Kichler Lighting

Kichler Lighting Vinea 52 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Richland II Bedienungsanleitung

Kichler Lighting

Kichler Lighting Guardian 330057 Bedienungsanleitung

Kichler Lighting

Kichler Lighting HATTERAS BAY PATIOLED 60" Bedienungsanleitung

Kichler Lighting

Kichler Lighting Seaside Bedienungsanleitung

Kichler Lighting

Kichler Lighting Sterling Manor Bedienungsanleitung

Kichler Lighting

Kichler Lighting 300457 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Jace LED Bedienungsanleitung

Kichler Lighting

Kichler Lighting Terna 300230 Bedienungsanleitung

Kichler Lighting

Kichler Lighting BASICS PRO PREMIER 330016WH Bedienungsanleitung

Kichler Lighting

Kichler Lighting Monarch II Patio Bedienungsanleitung

Kichler Lighting

Kichler Lighting 339211APP Bedienungsanleitung

Kichler Lighting

Kichler Lighting 35156 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Canfield Patio 310192 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Starkk 330180MWH Bedienungsanleitung

Kichler Lighting

Kichler Lighting ERIS 337060 Bedienungsanleitung

Kichler Lighting

Kichler Lighting Arkwet Weather+ Bedienungsanleitung

Kichler Lighting

Kichler Lighting Emerson HIGH COUNTRY Bedienungsanleitung

Kichler Lighting

Kichler Lighting RIDLEY2 KLF-RIDLEY2-52-NB Bedienungsanleitung

Kichler Lighting

Kichler Lighting ZEUS KLF-ZEUS-60-WHT-BN Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung