Kidde SLED177i Bedienungsanleitung

ATTENTION! The model SLED177i strobe light is designed to notify hearing impaired

individuals of impending danger. The strobe light has no detection means and MUST be

used in conjunction with operating and interconnected Smoke, Heat, or Carbon

Monoxide Alarms.

The model SLED177i AC wire-in Strobe light can be directly interconnected with Kidde

Safety 3-wire Smoke, Heat and CO alarms. It will produce an intermittent strobe flash

pattern (approximately 4 flashes, followed by approximately 5 seconds off) when trig-

gered by a Carbon Monoxide alarm and a flash every second when triggered by a

smoke or heat alarm.

Thank you for purchasing this strobe light. It is an important part of your family’s home

safety plan. You can trust KIDDE Safety to provide the highest quality safety products.

We know you expect nothing less when the lives of your family are at stake.

For model: SLED177i

1102-7201-00

Strobe

Light

For your convenience, write down the following information. If you call

our Consumer Hotline, these are the first questions you will be asked.

Strobe Light Model Number

(located on back of alarm):

Date Code (located on back of device):

Date of Purchase:

Where Purchased:

SLED177i

Strobe Light User Guide

1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 1

IMPORTANT! READ ALL INSTRUCTIONS BEFORE INSTALLATION AND SAVE

THIS USER GUIDE FOR FUTURE REFERENCE

WARNING! THIS VISUAL SIGNALING DEVICE HAS NO DETECTION

MEANS. IT MUST BE USED IN CONJUNCTION WITH OPERATING AND

INTERCONNECTED ALARMS.

WARNING! DO NOT TRY TO REPAIR THIS STROBE LIGHT YOURSELF

REFER TO THE INSTRUCTIONS IN SECTION 11 FOR SERVICE.

WARNING! DISCONNECTING OR LOSS OF AC POWER WILL RENDER

THIS SIGNALING DEVICE INOPERATIVE.

WARNING! THIS STROBE LIGHT IS EXTREMELY BRIGHT. DO NOT LOOK

DIRECTLY AT THE LIGHT WHEN THE LIGHT IS FLASHING..

CONTENTS OF THIS USER GUIDE

1 -- SPECIFICATIONS

2 -- APPLICATIONS

3 -- RECOMMENDED APPLICATIONS OF STROBE LIGHTS

4 -- LOCATIONS TO AVOID

5 -- INSTALLATION INSTRUCTIONS

6 -- OPERATION AND TESTING

7 -- MAINTENANCE

8 -- LIMITATIONS OF SIGNALING DEVICES FOR THE HEARING IMPAIRED

9 -- GOOD SAFETY HABITS

10 -- NFPA PROTECTION STANDARD 72

11 -- SERVICE AND WARRANTY

1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 2

1. SPECIFICATIONS

Model Number: SLED177i ( 3 WIRE INTERCONNECT UNIT )

Electrical Rating:

Regulated 120VAC (96-132VAC)

Maximum Operating RMS Current 630 mA

Multiple station (24) interconnect unit, interfaces directly with Kidde

Safety:

Ion Smoke Alarm Models: 1235, 1275, 1276, 1285, i12020, i12020A

i12040, i12040A, i12060,i2060A, i4618,

i4618A, KN-SMFM-I, RF-SM-ACDC

Photo Smoke Alarms: PE120, P12040,

Photo / Ion Smoke Alarms: Pi2000, Pi2010,

Heat Alarm Models: HD135F,

CO / Ion Smoke Alarm Models: KN-COSM-I,KN-COSM-IB,

KN-COPE-I,KN-COSM-IC,

CO / Photo Smoke Alarm Models: KN-COPE-I,

Carbon Monoxide Alarms Models: KN-COB-IC,KN-COP-IC

Strobe Light: SLED177i, SL177i

Relay Modules: SM120X, CO120X

Smoke or heat alarm events: Constant 1 flash per second nominal

Flash Rate (CO alarm event): Intermittent 1 flash per second nominal

(approximately 4 flashes, followed by

approximately 5 seconds OFF)

Temperature Limits: 0°C (32°F) to 49°C (120°F)

Mounting: Wall or Ceiling

Applications: Primary Direct or Indirect and Supplementary

Light Output: 177 Candela minimum (on axis

measurement)

1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 3

The following diagram shows that the light intensity gradually decreases as the

viewing angle is increased. Use this information to determine the best location

for the strobe light.

2. APPLICATIONS

PRIMARY DIRECT AND INDIRECT VISIBLE SIGNAL

Locate the strobe light on the ceiling in the center of the room or on

the wall a minimum of 80"(2 m) above the floor.

For rooms larger than 250 sq. ft. (14 ft. by 16 ft. - 4.27m by 4.88 m) the

notification device should be located within 16 feet of the pillow when located in a

sleeping area.

SUPPLEMENTARY VISIBLE SIGNAL

The strobe must be located more than 30 inches above the floor.

3. RECOMMENDED LOCATIONS OF VISUAL SIGNALING DEVICES

• Locate the first strobe light in the bedroom in which the hearing impaired

individual sleeps. If the bedroom door is kept closed at night, an

interconnecting smoke detector must also be installed in that bedroom.

• Locate additional strobe lights in any lived-in room where a hearing impaired

individual would need to be notified of an alarm condition.

4. LOCATIONS TO AVOID

• In direct sunlight or high ambient light areas; the bright light may reduce one’s

ability to notice the strobe light.

•

In areas where the temperature may fall below 0°C (32°F) or rise above 49°C (120°F).

• In areas with high humidity.

• Do not use outdoors (This device is not listed for outdoor use).

WALL

CEILING

25 90

25 85

30 80

30 75

35 70

35 65

40 60

45 55

55 50

75 30-45

90 5-25

100 0

(LIGHT INTENSITY) (IN DEGREES)

PERCENT ANGLE

90°

90° 90°

0°

45°

45°45°

SOURCE

LIGHT

SOURCE

LIGHT

WALL

CEILING

25 90

25 85

30 80

30 75

35 70

35 65

40 60

45 55

55 50

75 30-45

90 5-25

100 0

(LIGHT INTENSITY) (IN DEGREES)

PERCENT ANGLE

90°

90° 90°

0°

45°

45°45°

SOURCE

LIGHT

SOURCE

LIGHT

1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 4

5. INSTALLATION INSTRUCTIONS

READ CAREFULLY – WIRING REQUIREMENTS

• This smoke alarm should be installed on a U.L. listed or recognized junction

box. All connections should be made by a qualified electrician and all wiring

used shall be in accordance with articles 210 and 300.3(B) of the U.S. National

Electrical Code ANSI/NFPA 70, NFPA 72 and/or any other codes having jurisdic-

tion in your area. The multiple station interconnect wiring to the alarms must

be run in the same raceway or cable as the AC power wiring. In addition, the

resistance of the interconnect wiring shall be a maximum of 10 ohms.

• The appropriate power source is regulated 120VAC (96-132VAC) AC single

phase supplied from a non-switched circuit, which is not protected by a ground

fault interrupter.

MODEL SLED177i WIRING INSTRUCTIONS: For AC QUICK CONNECT 3 WIRE HARNESS.

WARNING: This alarm cannot be operated from power derived from a

square wave, modified square wave or modified sine wave inverter. These type

of inverters are sometimes used to supply power to the structure in off grid

installations, such as solar or wind derived power sources. These power sources

produce high peak voltages that will damage the strobe light.

CAUTION! TURN OFF THE MAIN POWER TO THE CIRCUIT BEFORE

WIRING THE STROBE LIGHT.

1. When Strobe lights and alarms are interconnected, all the interconnected

devices must be powered from the same circuit.

2. A maximum of 24 Kidde Safety devices may be interconnected in a multiple

station arrangement. The interconnect system should not exceed the NFPA

interconnect limits of 12 smoke alarms and/or 18 alarms total (smoke, heat,

Carbon Monoxide, etc). With 18 interconnected alarms it is still possible to

interconnect up to a total of 6 remote signaling devices and/or relay modules.

NOTE: WHEN MIXING MODELS WHICH HAVE BATTERY BACKUP (1275,

1275CA, 1276, 1276CA, 1285, i12040, i12040CA, i12040A, i12040ACA,

i12060, i12060CA, i12060ACA, i12080, i4618, i4618CA, KN-SMFM-I-CA,

PE120, PE120CA, P12040, P12040ACA, Pi2000CA, Pi2010, Pi2010CA,

KN-COSM-IB, KN-COSM-IBCA, RF-SM-ACDC, HD135, KN-COB-IC, KN-COB-IC-CA,

KN-COP-IC, KNCOP-IC-CA,KN-COPE-I, KN-COPE-ICA) WITH MODELS WITHOUT

BATTERY BACKUP (1235, 1235CA, i12020, i12020CA, i12020A, i12020ACA,

KN-COSM-I, KN-COSM-ICA, KN-COB-ICB-CA, CO120X, SM120X AND SL177i,

SLED177iCA), BE ADVISED THAT THE MODELS WITHOUT BATTERY BACKUP WILL

NOT FUNCTION DURING AN AC POWER FAILURE.

1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 5

4. The maximum wire run distance between the first and last device in an inter-

connect system is 1000 ft.

5. Figure 1 illustrates interconnection wiring. Improper connection will result in

damage to the strobe light or alarms, failure to operate, or a shock hazard.

6. Make certain that all devices in the interconnect system are wired to a contin-

uous (non-switched, non-GFI or GCFI protected) power line.

FIGURE 1: INTERCONNECT WIRING DIAGRAM.

WIRE NUT

EQUIVALENT

WHITE

BLACK

RED

WHITE

RED

BLACK

WHITE

RED

BLACK

FUSE OR CIRCUIT BREAKER

SMOKE ALARM

STROBE LIGHT

HEAT ALARM

CO ALARM

FIGURE 1

WIRING OF STROBE AC QUICK CONNECT THREE WIRE HARNESS

WIRES ON ALARM HARNESS CONNECTED TO:

BLACK HOT SIDE OF AC LINE

WHITE NEUTRAL AC LINE

RED INTERCONNECT LINES (RED WIRES) OF THE OTHER UNITS IN

THE MULTIPLE STATION SET UP

1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 6

MOUNTING INSTRUCTIONS:

• A mounting plate is provided on the back of the strobe light. This mounting

plate is installed on the electrical box between the electrical box and the

strobe light.

• Remove the mounting plate from the back of the strobe light by holding the

mounting plate and twisting the strobe light in the direction indicated by the

"OFF" arrow on the cover.

CAUTION: THIS UNIT IS SEALED. THE COVER IS NOT REMOVABLE! After

selecting the proper strobe light location as described in section 3, and wiring

the AC QUICK CONNECT harness as described in the WIRING INSTRUCTIONS,

attach the mounting plate to the electrical box (see fig. 2).

FIGURE 2: SELECT PROPER MOUNTING HOLES ON THE MOUNTING PLATE

• Use a screwdriver to punch out only the pair of holes in the mounting plate

that match your type of electrical box or plaster ring. Mount the mounting

plate to the electrical box using the appropriate holes. NOTE: Use the circle,

square, and octagon markings near each mounting hole in the mounting plate

to help you select the correct mounting holes (see fig. 2).

Rectangular

Plaster Ring

Circular

Plaster Ring

Octagonal

Electrical Box

FIGURE 2

1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 7

•

Pull the AC QUICK CONNECTOR through the center hole in the mounting plate and

install the mounting plate, making sure that the mounting screws are positioned in

the small ends of the keyholes before tightening the screws (see fig. 2).

• Plug the AC QUICK CONNECTOR into the back of the strobe light, (see fig. 3)

making sure that the locks on the connector snap into place. To remove AC con-

nector, squeeze locking arm and pull.

•

If you have finished all the WIRING AND MOUNTING PLATE MOUNTING STEPS,

you can install the strobe light on the mounting plate. Alignment marks are

provided on the side of the strobe light and mounting plate. With the indicating

marks aligned and rotate the strobe light in the direction of the ON arrow on

the cover until the strobe light snaps in place. (See fig. 4)

• Turn on the AC power. The model SLED177i strobe light has a green AC

power on indicator which should be lit when the strobe is correctly powered.

TAMPER RESIST LOCKING PIN: To make your strobe light tamper resistant a

locking pin has been provided with your strobe light. Using this pin will help

deter individuals from removing the strobe light from the mounting plate. To use

the pin insert it into the hole in the side of the strobe light after the strobe light

has been installed on the mounting plate (see fig. 5). NOTE: The tamper resist

pin will have to be removed in order to remove the strobe light. This can be

done easily with a long nose pliers. Using the long nose pliers, pull the pin out

of the hole, it is now possible to remove the strobe light from the mounting

plate.

After installation test your strobe light by following the test procedure outlined

in section 6.

Tamper resistant

locking pin

Alignment Marks

FIGURE 3 FIGURE 4 FIGURE 5

Install Remove

1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 8

CAUTION! Early warning fire detection and visual notification is best

achieved by the installation of fire detection and visual notification equipment in

all rooms and areas of the household as follows: A smoke alarm and visual

notification device installed and interconnected in each separate sleeping area,

and visual notification equipment interconnected with heat, smoke, or CO

alarms in the living rooms, dining rooms, kitchens, hallways, attics, furnace

rooms, closets, utility storage rooms, basements, and attached garages.

6. TESTING AND OPERATION

WARNING! THIS STROBE LIGHT IS EXTREMELY BRIGHT. DO NOT LOOK

DIRECTLY AT THE LIGHT .

TESTING: Push the test button on one of the interconnected alarms to activate

the test sequence for the alarm.

The controlling alarm will also send an activation signal through the

interconnecting wiring to the strobe light, and cause the strobe light to flash if

the strobe light and the interconnection wiring are working properly.

If the strobe does not activate check the fuse or circuit breaker supplying power

to the alarm circuit.

If the strobe does not activate perform the maintenance steps in the alarm’s

User Guide.

Check the operation of the strobe light by executing a test on another

interconnected alarm.

TEST THE STROBE LIGHT AND YOUR ALARMS WEEKLY TO ENSURE

PROPER OPERATION.

OPERATION: The strobe light is operating once AC power is applied, the green

LED is illuminated, and testing is complete. When the strobe light is activated by

an interconnected alarm, it will flash for as long as the controlling alarm remains

active.

7. MAINTENANCE

STROBE LIGHT REMOVAL:

IF TAMPER RESIST PIN HAS BEEN USED, REFER TO “TAMPER RESIST LOCKING

1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 9

PIN” IN SECTION (5) FOR PIN REMOVAL INSTRUCTIONS.

CLEANING YOUR STROBE LIGHT:

To clean your Strobe light remove it from the mounting plate and disconnect the

AC Quick Connect power harness as outlined in section 5.

You can clean dust from your strobe light by using a vacuum cleaner hose and

vacuuming around the cover and lens openings on the strobe light.

The outside of the strobe light can be wiped with a damp cloth.

AFTER CLEANING, REINSTALL YOUR STROBE LIGHT AND TEST YOUR

STROBE LIGHT BY ACTIVATING ONE OF THE CONTROLLING ALARMS.

8. LIMITATIONS OF ALARM CONTROLLED VISUAL SIGNALING

DEVICES

VISUAL SIGNALING DEVICES CAN PROVIDE EARLY WARNING TO HEARING

IMPAIRED INDIVIDUALS AT A REASONABLE COST; HOWEVER, IN ORDER FOR

THE VISUAL SIGNALING DEVICE TO FUNCTION, IT MUST BE ACTIVATED BY AN

OPERATING ALARM. ALARMS CANNOT PROVIDE AN ACTIVATION SIGNAL TO

THE VISUAL SIGNALING DEVICE IF SMOKE, HEAT OR CARBON MONOXIDE DO

NOT REACH THE SPECIFIC ALARM. THEREFORE, ALARMS MAY NOT SENSE A

CONDITION ON A DIFFERENT FLOOR, OR ON THE OTHER SIDE OF A CLOSED

DOOR. ALARMS DO HAVE LIMITATIONS. AC POWERED ALARMS WILL NOT

OPERATE IF AC POWER HAS BEEN CUT OFF BY AN ELECTRICAL FIRE OR AN

OPEN FUSE.

HOME EMERGENCIES DEVELOP IN DIFFERENT WAYS AND ARE OFTEN UNPRE-

DICTABLE. NO ONE TYPE OF CONTROLLING ALARM; HEAT, FIRE (IONIZATION OR

PHOTOELECTRIC) OR CARBON MONOXIDE IS ALWAYS BEST. FOR MAXIMUM

PROTECTION, ALARMS MUST BE INSTALLED IN EACH SLEEPING AREA, AND ON

EVERY LEVEL OF A HOME. ALARMS MUST BE INTERCONNECTED WITH EACH

OTHER AND THE SIGNALING DEVICES AND BE TESTED REGULARLY TO INSURE

THE ALARMS AND INTERCONNECTING CIRCUITS ARE IN GOOD OPERATING

CONDITION.

IN AN UNDERWRITERS LABORATORIES STUDY, THIS TYPE OF VISUAL SIGNALING

APPLIANCE WAS ONLY SUCCESSFUL IN WAKING 92% OF THE SLEEPING

RESPONDENTS.

HEARING IMPAIRED INDIVIDUALS MAY NOT SEE THE VISUAL WARNING DEVICE

IF WALLS, DOORS, DISTANCE, HIGH AMBIENT LIGHT, OR OTHER OBSTRUCTIONS

BLOCK THE STROBE LIGHT. IF THE STROBE LIGHT IS LOCATED OUTSIDE THE

1102-7201-00_Rev.A_EN_V8:_ 2013.5.28 9:45 AM Page 10

Inhaltsverzeichnis

Andere Kidde Sicherheitssystem Handbücher

Kidde

Kidde KN-COP-DP-10YL-AQ-WF Bedienungsanleitung

Kidde

Kidde KN-COB-DP2CA Bedienungsanleitung

Kidde

Kidde SLICK RF-SFTP Bedienungsanleitung

Kidde

Kidde 8LLCO Bedienungsanleitung

Kidde

Kidde FireBeta XT+ Bedienungsanleitung

Kidde

Kidde KN-COB-IC Bedienungsanleitung

Kidde

Kidde Truesense Combo Bedienungsanleitung

Kidde

Kidde Fyrnetics Slick 1SFW Bedienungsanleitung

Kidde

Kidde 900-CUAR-VCA Bedienungsanleitung

Kidde

Kidde KF10 Bedienungsanleitung

Kidde

Kidde WFPCO Bedienungsanleitung

Kidde

Kidde 7CO Bedienungsanleitung

Kidde

Kidde KN-COB-DP-H) Bedienungsanleitung

Kidde

Kidde KN-COB-LP2 Bedienungsanleitung

Kidde

Kidde KN-COPE-DCA Bedienungsanleitung

Kidde

Kidde KN-COB-B Bedienungsanleitung

Kidde

Kidde 10LLDCO Bedienungsanleitung

Kidde

Kidde KN-COP-DP-10YH Bedienungsanleitung

Kidde

Kidde 4MCO Bedienungsanleitung

Kidde

Kidde ZP885 Montageanleitung

Kidde

Kidde 4MCO Bedienungsanleitung

Kidde

Kidde P4010ACSCOAQ-WF Bedienungsanleitung

Kidde

Kidde KN-COPE-D Bedienungsanleitung

Kidde

Kidde KN-COP-DP-10YL-AQ-WF Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung