Kirisun PT6500 Bedienungsanleitung

FM HANDHELD TRANSCEIVER

INSTRUCTION MANUAL

PT6500

We are very grateful for your purchasing brand two-

way radios produced by Kirisun Electronics (Shenzhen) Co.,

Ltd.

We believe two-way radio, which always incorporates

the latest technology, can bring great convenience to your life

and work;

We also believe that the quality and function of two-

way radio can meet your demands for reliable communication.

PRECAUTIONS

Please observe the following precautions to prevent fire,

personal injury, and radio damage.

Do not operate your radio while taking on fuel, or being

charged.

Do not expose the radio for a long period to direct sunlight,

nor place the radio close to heating appliances.

Do not place the radio in excessively dusty areas, humid

INSTRUCTION MANUAL

FM HANDHELD TRANSCEIVER

PT6500

NOTE

areas or on unstable surfaces.

Do not modify this radio for any reason.

Refer service to qualified licensed or certificated technicians

only.

Notice to the User:

Government laws prohibit radio communication without

permission in government districts.

Illegal operation is subject to punishment by fine and/or

imprisonment.

Refer service to the well-trained professional technicians only.

Safety

It is important that the user is aware of and understands hazards

common to the operation of any radios.

Warning!

Turn off your radio before entering any area with a potentially

explosive atmosphere (where the air contains gas, dust and

smog, etc.), such as while taking on fuel, or while parking at a

gasoline service station.

Precautions in Use

Please comply with the following attentions to avoid fire, bodily

injury and damage to the radio.

The radio is recommended to transmit for 1 minute and

receive for 4 minutes. Long time transmitting or continuous working in

high power mode will make the rear side of the radio generate heat.

Please don't disassemble or assemble the radio under any

circumstances.

Please don't expose the radio to direct sunlight for a long time;

don't place the radio near any heating devices, either.

Please don't put the radio in extremely dusty, moist or dabbling

places; don't place it on any unstable surfaces, either.

If the radio emits smoke or strange odors, turn it off and remove

the battery from the radio and promptly contact your local authorized

Kirisun dealer.

CONTENTS

Unpacking and checking..............................................................1

Supplied accessories ..................................................................1

Preparation...................................................................................2

Charging the battery..................................................................2

Installing/Removing the battery pack.........................................3

Installing the antenna.................................................................4

Installing the optional speaker/microphone...............................4

Installing the belt clip.................................................................4

Radio Overview............................................................................5

Basic Operation............................................................................7

Programmable Button functions.................................................14

VOX............................................................................................22

Whole setting..............................................................................22

Time-out Timer TOT ...........................................................22

Battery Saving..........................................................................23

Low Power Warning.................................................................23

Channel Annunciation..............................................................24

CTCSS/ DCS User's resolution................................................24

Busy Channel Lockout BCL ................................................24

Receiving Squelch Mode.........................................................24

DTMF signaling .......................................................................25

2TONE signaling .....................................................................25

5TONE signaling .....................................................................26

Transmit beginning/ending signaling (PTT ID) ........................26

Problems and troubleshooting .................................................27

Major Specifications...................................................................28

Status setting..............................................................................29

V071123

ITEM QUANTITY

UNPACKING AND CHECKING EQUIPMENT

Carefully unpack the radio. We recommend that you

identify the items listed in the following table before discarding the

packing material. If any damage has occurred during shipment,

please contact the dealer immediately .

SUPPLIED ACCESSORIES

Hand strap

Belt clip

Li-Polymer battery

Charger

Power adapter

Instruction manual

Antenna

PREPARATION

CHARGING THE BATTERY PACK

Plug the power adapter into the proper AC wall

outlet; and insert the cable of the power adapter

into the adapter socket on the charger; then the

charger indicator lights green.

Insert the battery or the radio to be charged into

the charger slot.

Make sure the battery is in good contact with the

charger terminals. When the red indicator lights,

the charger begins to charge the battery.

After charging for about 5 hours, the red

indicator turns dim and the green indicator lights

indicating the battery has been fully charged.

Leave the battery in that sate of green indicator for 1~2 hours

before you remove it from the charger to achieve the best

performance of the battery. Then you can disconnect the power

adapter from the AC outlet.

Notes:

* The battery is not fully charged in the factory. Before the initial use,

please charge the new battery.

* The KB-36A Ni-MH battery/KB-36C Li-Ploy battery of Kirisun is

adaptable with this radio.

* When you charge the battery the first time or after long time storage

Antenna Power adapter

Belt clip

Charger

Hand strap

Battery

INSTALLING /REMOVING THE BATTERY PACK

Notes:

Do not cause short-circuit or throw the battery to the fire.

Do not disassemble the battery by yourself.

Installing the Battery Pack

Match the 3 bulges of the battery pack with the

corresponding slots at the rear bottom of the radio.

Installing the Battery Pack

Then firmly press the battery pack downwards to

lock it in place until a click is heard.

Removing the Battery Pack

To remove the battery pack, use your thumb to

press the belt clip, one side of your index finger to

press the release button and then pull the battery

away from the radio.

(2 months), several times of charging is needed. Make sure the

battery is charged at least once every three months.

* Do not charge the battery again if it is charged fully or not in the low-

pressure warning mode, otherwise, it will have bad effects on its life

and performance. Remove the battery from the charger after charging.

* When you use the KB-36A battery, and the transceiver is in the low-

power warning mode, recharge the battery before use. Do not start up

by force; otherwise, it will have bad effects on its life and performance.

* There is a protection circuit in KB-36C battery, so the power will be

cut off at too low power.

INSTALLING THE ANTENNA

Screw the antenna into the connector at

the top of the transceiver by holding the

Button of the antenna and turn it

clockwise until secure.

INSTALLING THE OPTIONAL

SPEAKER/ MICROPHONE

Insert the speaker/microphone plug into

the jacks of the versatile connector.

INSTALLING THE BELT CLIP

Match the grooves of the belt clip with

those on the rear of the battery. Then

press belt clip downwards to lock it in

place. Push the card by inserting your

nail or tool into the groove at the upper

part of the clip to remove the belt clip.

SVC

123

456

789

*0#

The functions of the components are as follows:

A. LED Indicator

Lights red while transmitting;

Lights green while receiving.

B. Power/Volume Switch Knob

Turn clockwise till a click is heard to switch on the radio.

Turn counterclockwise till a click is heard to switch off the radio.

Rotate to adjust the volume after turning on the radio.

C. Channel Selector

Rotate to select the channel 1-128.

D. Antenna

E. Top Button (programmable button)

It is recommended to be set as the emergency warning Button.

F. Side button 1 (programmable button)

G. PTT PUSH-TO-TALK :

To make a call, press and hold the PTT button, then speak into the

microphone with normal voice. Release the PTT button to receive

signals.

H. Side button 2 (programmable button)

RADIO OVERVIEW I. Button

Return and delete button in the menu.

J. Button

Select Button.

K. Button

Select Button.

L. Button

Enter and Confirm Button.

M. Numeric keypad

N. Microphone/speaker jacks

For connecting microphone/speaker.

Explanation for the screen

Description

Signal intensity

SVC

Compandor

Disturbance Frequency

Busy channel lockout

Scanning

Key lockout

Signal reminder is programmed

Battery capacity, flashes when the battery power goes too low

Icon

BASIC OPERATION

5. Receive a Call

Release the PTT button to receive a call.

Your dealer can set CTCSS, DCS, 2 Tone signaling on your

radio channels by PC software. If you select a channel that has

been preset with the tone signaling, you will not hear any other

calls except those from your own system.

1.Switch On

Switch on the radio by turning the Power/Volume

switch clockwise

till a click is heard, then the radio will be in the

state of stand by and you will hear a beep if the

dealer has set it.

2.Adjust Capacity

Press the button preset as canceling squelch to

listen to the background noise and rotate the

Power/Volume switch to adjust capacity.

3.Select Channels

Rotate the channel selector to select channels.

You will hear voice from the speaker while

receiving proper signals.

As shown in the above right figure:

Zone 1 is the zone of current channel (8

zones from 0 to 7).

H is the transmit power of the channel, H

stands for high power, M for middle

power while L for low power.

CHANNEL 1 is the current channel (128

zones from 1 to 128).

4. Make a Call

To make a call, press PTT, and speak in normal

voice. Please keep your mouth 3~4 cm away from

the microphone.

6. Operation on menu:

press button to enter the menu or confirm any contents;

press button to return to the previous menu or cancel

the set. When entered the menu, select the sub-menu with the

channel selector , or .

The menu is as follows:

Phone

Utilities

Scan Back Light

Squelch Level

Power Level

Key tone

Scrambler

Save

Companding

Rptr/Talkamd

Speak mode

Zone Edit

Call

Ch Edit

Rx FRQ

Tx CTCSS

ON/OFF

Tx FRQ

Rx CTCSS

Level: 0~9 HML

ON/OFF

ON/OFF ON/OFF

The operations are as follows:

Set scanning:

1. As shown: in CH 1 , press , then Utilities

is shown;

2. Press , then Scan is shown;

3. Press , then enter selecting Scan ;

4. Select Scan On or Scan OFF with / , then press to

confirm it.

If can not enter that way, you have to set in PC communications;

Set back light:

1. As shown: in CH 1 , press , Utilities is shown.

2. Press to enter select mode,

3. Press / , and Back Light is shown,

4. Press to select On or OFF ,

5. Select On or OFF with / , press to confirm.

Set the squelch level:

1. As shown: in CH 1 , press , Utilities is shown.

2. Press to enter select mode,

3. Press / , then Squelch Level is shown,

4. Press to select squelch level, e.g., Level 0

5. Change the squelch level with / , then press to confirm.

Set power level (high/middle/low):

1. As shown: in CH 1 , press , utilities is shown.

2. Press to enter select mode,

3. Press / , then Power Level is shown,

4. Press to select, e.g., Power Low ,

5. Change the power level with / , then press to confirm.

Set Companding

1 As shown: in CH 1 , press , Utilities is shown.

2. Press to enter select mode,

3. Press / , and Companding is shown,

4. Press to select Companding ,

5. Select On or OFF by / , press to confirm.

11 12

Set saving

1 As shown: in CH 1 , press , Utilities is shown.

2. Press to enter select mode,

3. Press / , and Save is shown,

4. Press to select Save 1 4 ,

5. Chang the save percentage with / , press to confirm.

Set scrambler

1 As shown: in CH 1 , press , Utilities is shown.

2. Press to enter select mode,

3. Press / , and Scrambler is shown,

4. Press to select, e.g., Scrambler OFF ,

5. Select On or OFF by / , press to confirm.

Set key tone

1 As shown: in CH 1 , press , Utilities is shown.

2. Press to enter select mode,

3. Press / , and Key Tone is shown,

4. Press to select OFF or On ,

5. Select On or OFF with / , press to confirm.

Set Rptr/Talkarnd

1 As shown: in CH 1 , press to enter select mode,

2. Press / , and Rptr/Talkarnd is shown,

3. Press to select the mode,

4. Select Repeater Mode or Talkarnd mode with / ,press

to confirm.

Set speak On mode

1 As shown: in CH 1 , press to enter select mode,

2. Press / , and Speak Mode is shown,

3. Press to select the speak on mode,

4. Select with / , press to confirm.

Set zone mode

1 As shown: in CH 1 , press to enter select mode,

2. Press / , and Zone Edit is shown,

3. Press to select the zone mode,

4. Select Zone No with / , press to confirm.

Set call list

1 As shown: in CH 1 , press to enter select mode,

2. Press / , and Call is shown,

3. Press to select the call list,

4. Select with / , press PTT to transmit.

Set Rx FRQ

1 As shown: in CH 1 , press to enter select mode,

2. Press / , and Ch Edit is shown,

3. Press to select

4. Press , is shown, enter the set of Rx FRQ,

5 Set the Rx FRQ value with the keypad,

6. Press to delete, and press to confirm.

Set Tx FRQ

1 As shown: in CH 1 , press to enter select mode,

2. Press / , and Ch Edit is shown,

3. Press to select

P2P3

P3P

P3Rx FRQ

401.660000

Ch alias

CHANNEL 1

Ch alias

CHANNEL 1

Andere Handbücher für PT6500

Inhaltsverzeichnis

Andere Kirisun Transceiver Handbücher

Kirisun

Kirisun PT6800 Bedienungsanleitung

Kirisun

Kirisun PT578 Bedienungsanleitung

Kirisun

Kirisun PT5200 Bedienungsanleitung

Kirisun

Kirisun PT6500 Bedienungsanleitung

Kirisun

Kirisun PT3600 Bedienungsanleitung

Kirisun

Kirisun PT8000 Bedienungsanleitung

Kirisun

Kirisun PT6500 Bedienungsanleitung

Kirisun

Kirisun PT260 Bedienungsanleitung

Kirisun

Kirisun PT8200 Bedienungsanleitung

Kirisun

Kirisun PT6700 Bedienungsanleitung

Kirisun

Kirisun PT2208 Bedienungsanleitung

Kirisun

Kirisun PT3600 Bedienungsanleitung

Kirisun

Kirisun PT7200 Bedienungs- und Wartungshandbuch

Kirisun

Kirisun PT4208 Bedienungsanleitung

Kirisun

Kirisun PT56803 Bedienungsanleitung

Kirisun

Kirisun PT568 Bedienungsanleitung

Kirisun

Kirisun PT360002 Bedienungsanleitung

Kirisun

Kirisun PT4208 Bedienungsanleitung

Kirisun

Kirisun PT8200 Bedienungsanleitung

Kirisun

Kirisun PT4200 Bedienungsanleitung

Kirisun

Kirisun PT 3800(1) Bedienungsanleitung

Kirisun

Kirisun PT6200 Bedienungsanleitung

Kirisun

Kirisun PT800001 Bedienungsanleitung

Kirisun

Kirisun PT3600 Bedienungsanleitung

Beliebte Transceiver Handbücher anderer Marken

Yaesu

Yaesu FT-7B Bedienungsanleitung

Kenwood

Kenwood ProTalk TK-3201 Bedienungsanleitung

Texas Instruments

Texas Instruments TLK10232 Bedienungsanleitung

Mizuho

Mizuho MX-2 Produkthandbuch

Kenwood

Kenwood TK-3180 Bedienungs- und Wartungshandbuch

Blitz

Blitz MJ-398U Bedienungsanleitung

Utilicom

Utilicom LongRanger 2050 Bedienungsanleitung

Standart

Standart HX290UKA Bedienungsanleitung

Altronix

Altronix Pace1PTM Bedienungsanleitung

ELECRAFT

ELECRAFT KX2 Bedienungsanleitung

Zodiac

Zodiac K3 Bedienungsanleitung

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Bedienungsanleitung

Kenwood

Kenwood TK-2217 Bedienungsanleitung

Siemens

Siemens PSO 4000 Bedienungsanleitung

Kenwood

Kenwood TS-590SG Bedienungsanleitung

Midland

Midland G8E-BT Handbuch

ComNav

ComNav Mariner X2 Bedienungsanleitung

Uniden

Uniden UH820 Series Bedienungsanleitung