KitchenAid KUBL204EPA Bedienungsanleitung

BEVERAGE CENTER

OVERLAY MODEL

Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service, call: 1-800-422-1230 or visit our website at...

www.kitchenaid.com

In Canada, call: 1-800-807-6777, or visit our website at...

www.KitchenAid.ca

REFRIGERADOR PARA BEBIDAS

MODELO RECUBIERTO

Manual de uso y cuidado

Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico, llame al:

1-800-422-1230 o visite nuestro sitio de internet en...

www.kitchenaid.com

En Canadá, llame al: 1-800-807-6777, o visite nuestro sitio de internet en...

www.KitchenAid.ca

RÉFRIGÉRATEUR POUR BOISSONS

MODÈLE À PANNEAU DÉCORATIF

Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web à...

www.KitchenAid.ca

Table of Contents/Índice/Table des matières ..................................................................2

W10741573C/8336460126900C

TABLE OF CONTENTS

BEVERAGE CENTER SAFETY ......................................................3

INSTALLATION REQUIREMENTS................................................4

Tools and Parts ............................................................................4

Location Requirements................................................................4

Custom Overlay Frame ................................................................4

Electrical Requirements ...............................................................5

INSTALLATION INSTRUCTIONS..................................................6

Unpack the Beverage Center.......................................................6

Install Custom Overlay Frame......................................................6

Door Closing.................................................................................8

BEVERAGE CENTER USE.............................................................8

Normal Sounds ............................................................................8

Using the Controls .......................................................................8

Beverage Shelf/Wine Racks.......................................................10

Stocking the Beverage Center...................................................10

BEVERAGE CENTER CARE ........................................................11

Base Grille ..................................................................................11

Cleaning......................................................................................11

Vacation and Moving Care.........................................................12

TROUBLESHOOTING ..................................................................12

ASSISTANCE OR SERVICE.........................................................13

In the U.S.A. ...............................................................................13

In Canada ...................................................................................13

Accessories ................................................................................13

WARRANTY ..................................................................................14

ÍNDICE

SEGURIDAD DEL REFRIGERADOR PARA BEBIDAS ..............15

REQUISITOS DE INSTALACIÓN.................................................16

Herramientas y piezas................................................................16

Requisitos de ubicación.............................................................16

Marco recubierto a la medida....................................................16

Requisitos eléctricos..................................................................18

INSTRUCCIONES DE INSTALACIÓN.........................................18

Desempaque del refrigerador para bebidas..............................18

Cómo instalar el marco

recubierto a la medida ...............................................................18

Cierre de la puerta......................................................................20

USO DEL REFRIGERADOR PARA BEBIDAS ............................21

Sonidos normales ......................................................................21

Uso de los controles ..................................................................21

Estante para bebidas/portabotellas...........................................23

Cómo almacenar en el refrigerador

para bebidas...............................................................................24

CUIDADO DEL REFRIGERADOR PARA BEBIDAS ...................24

Rejilla de la base.........................................................................24

Limpieza .....................................................................................24

Cuidado durante las vacaciones y mudanzas...........................25

SOLUCIÓN DE PROBLEMAS......................................................26

AYUDA O SERVICIO TÉCNICO...................................................27

En los EE.UU. .............................................................................27

En Canadá..................................................................................27

Accesorios..................................................................................27

GARANTÍA.....................................................................................28

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR POUR BOISSONS ..............30

EXIGENCES D’INSTALLATION...................................................31

Outillage et pièces......................................................................31

Exigences d'emplacement.........................................................31

Cadre décoratif personnalisé.....................................................32

Spécifications électriques..........................................................33

INSTRUCTIONS D’INSTALLATION ...........................................33

Déballage du réfrigérateur pour boissons .................................33

Installation du cadre décoratif personnalisé..............................33

Fermeture de la porte.................................................................35

UTILISATION DU RÉFRIGÉRATEUR POUR BOISSONS..........36

Sons normaux ............................................................................36

Utilisation des commandes........................................................36

Tablette à boissons/casiers à vin...............................................38

Stockage dans le réfrigérateur pour boissons...........................39

ENTRETIEN DU RÉFRIGÉRATEUR POUR BOISSONS ............39

Grille de la base..........................................................................39

Nettoyage ...................................................................................39

Précautions à prendre pour les vacances et avant

un déménagement .....................................................................40

DÉPANNAGE.................................................................................41

ASSISTANCE OU SERVICE.........................................................42

Aux États-Unis............................................................................42

Au Canada..................................................................................42

Accessoires ................................................................................42

GARANTIE.....................................................................................43

BEVERAGE CENTER SAFETY

Proper Disposal of Your Old

Refrigerated Appliance

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned beverage centers are still

dangerous – even if they will sit for “just a few days.” If you are

getting rid of your old beverage center, please follow these

instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerated appliance:

■Take off the door.

■Leave the shelves in place so that children may not easily

climb inside.

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your beverage center, follow these basic

SAVE THESE INSTRUCTIONS

■Plug into a grounded 3 prong outlet.

■Do not remove ground prong.

■Do not use an adapter.

■Do not use an extension cord.

■Disconnect power before servicing.

■Replace all parts and panels before operating.

■Remove door or drawer(s) from your old refrigerated

appliance.

■Use nonflammable cleaner.

■Keep flammable materials and vapors, such as gasoline,

away from beverage center.

■Use two or more people to move and install beverage

center.

precautions:

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

WARNING

Suffocation Hazard

Remove door or drawer(s) from your old refrigerated

appliance.

Failure to do so can result in death or brain damage.

Important information to know about disposal of

refrigerants:

Dispose of refrigerator in accordance with Federal and Local

regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with

established procedures.

INSTALLATION REQUIREMENTS

Tools and Parts

Tools Needed

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Parts Needed

Parts Supplied

Location Requirements

To ensure proper ventilation for your beverage center, allow for a

¹⁄₄" (6.35 mm) space on each side and at the top. When installing

your beverage center next to a fixed wall, leave 2¹⁄₂" (6.35 cm)

minimum clearance on the hinge side to allow for the door to

swing open.

NOTE: It is recommended that you do not install the beverage

center near an oven, radiator, or other heat source. Do not install

in a location where the temperature will fall below 55°F (13°C). For

best performance, do not install the beverage center behind a

cabinet door or block the base grille.

Opening Dimensions

■Height dimensions are shown with the leveling legs extended

to the minimum height.

NOTE: When leveling legs are fully extended, add ⁵⁄₈" (15 mm)

to the height dimensions.

■If the floor of the opening is not level with the kitchen floor,

shim the opening to make it level with the kitchen floor.

Custom Overlay Frame

If you plan to install a custom overlay frame, you will need to

create the frame yourself or consult a qualified cabinetmaker or

carpenter. See dimension drawings for frame specifications.

IMPORTANT:

■The thickness of the overlay frame must be ³⁄₄" (19 mm).

■The overlay frame must not weigh more than 10 lbs (4.54 kg).

Overlay frames weighing more than recommended may

cause damage to your appliance.

■Overlay frame drawings show the rear view of the frame.

■Cordless drill

■¹⁄₁₆" and ³⁄₈" Brad point

doweling drill bit

■Phillips screwdriver

■Rotary tool

■Scissors

■C-clamp

■Masking tape

■Tape measure

■Petroleum jelly

■Custom Overlay Frame—See “Overlay Frame—Rear

View.”

■Flat-head screws (TRUSS M4x34 Tapping) (8)

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from beverage center.

Failure to do so can result in death, explosion, or fire.

¹⁄₄" (6.35 mm)

2¹⁄₂" (6.35 cm)

Critical Dimensions:

A. 14

³⁄₄

" (37.5 cm) utility opening

B. 24" (60.96 cm) minimum opening width

¹⁄₂"

(1.3 cm)

14³⁄₄"

(37.5 cm)

24"

(60.96 cm)

min.

24" (60.96 cm) min.

34³⁄₈" (87.3 cm) min.

35" (88.9 cm) max.

Overlay Frame Dimensions—Rear View

1. Create a custom overlay frame using the dimensions shown.

Door Hinge Holes

■The views of the top and bottom hinge pin hole show a right-

hand hinge. Mirror the image for a left-hand hinge.

■We recommend using a C-clamp and two pieces of scrap

wood (front and back) to help reinforce the overlay frame

when drilling the hinge pin holes.

1. Using a ³⁄₈" brad point doweling drill bit, drill a hole, ¹⁄₄"

(6.35 mm) deep, into the top of the overlay frame for the top

hinge pin. Remove the excess wood, surrounding the hole, by

using the rotary tool to complete the hinge depression as

shown.

Top View

2. Using a ³⁄₈" brad point doweling drill bit, drill a hole, ³⁄₈"

(9,5 mm) deep, in the bottom of the overlay frame for the

bottom hinge pin. Remove the excess wood, surrounding the

hole, by using the rotary tool to complete the hinge

depression, as shown.

Bottom View

Electrical Requirements

Before you move your beverage center into its final location, it is

important to make sure you have the proper electrical

connection.

A. Diameter ³

⁄₈

" (10.0 mm)

22³⁄₄"

(57.8cm)

4⁵⁄₈"

(11.7 cm) 2³⁄₈"

(6.1 cm)

¹⁄₂"

(1.4 cm) 2³⁄₄"

(7.0 cm)

3¹⁄₂"

(9.0 cm)

(7.7 cm)

Top

Hole

Reverse Side

Bottom

23¾"

(60.3cm)

29¹³⁄₁₆"

(75.8cm)

17¹³⁄₁₆"

(45.2 cm)

(7.7 cm)

3¹⁄₂"

(9.0 cm)

2³⁄₄"

(7.0 cm)

¹⁄₂"

(1.4 cm)

4⁷⁄₈"

(12.4 cm)

2³⁄₄"

(7.0 cm)

Back Surface

Front Surface

³⁄₈" (10.0 mm)

¹⁄₂" (13.5 mm)

Depth

¹⁄₄"

(7.0 mm)

A. Diameter ³

⁄₈

" (10.0 mm)

¹⁄₄"

(7.0 mm)

³⁄₈" (9.5 mm)

Front

Front Surface

Back Surface

Depth

³⁄₈" (10.0 mm)

¹⁄₂" (13.5 mm)

³⁄₈"

(10.0 mm)

¹⁄₂" (13.5 mm)

³⁄₈" (10.0 mm)

Front Surface

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Recommended Grounding Method

A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your beverage center be provided. Use an

outlet that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, unplug beverage center or disconnect

power.

INSTALLATION

INSTRUCTIONS

Unpack the Beverage Center

Remove the Packaging

■Remove tape and glue residue from surfaces before turning

on the beverage center. Rub a small amount of liquid dish

soap over the adhesive with your fingers. Wipe with warm

water and dry.

■Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These

products can damage the surface of your beverage center.

For more information, see “Beverage Center Safety.”

■Dispose of/recycle all packaging materials.

Clean Before Using

After you remove all of the packaging materials, clean the inside

of your beverage center before using it. See the cleaning

instructions in “Beverage Center Care.”

Install Custom Overlay Frame

IMPORTANT:

■Create custom overlay frame according to the specifications

in the “Custom Overlay Frame” section.

■KitchenAid is not responsible for the removal or addition of

molding or decorative frames that would not allow access to

the appliance for service.

Remove the Door

IMPORTANT: Do not remove the grease from the washer, top

spacer or top hinge pin. Be sure to set aside the top hinge, top

spacer and washer for later use.

1. Using a Phillips screwdriver, remove the three screws from

the top hinge. Remove the top hinge.

2. Remove the washer. Keep in a safe place for later use.

3. Open the door. Lift the front of the door up, pulling straight

out to remove as shown.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

beverage center.

Failure to do so can result in back or other injury.

When MovingYour Beverage Center:

Your beverage center is heavy. When moving the appliance

for cleaning and service, be sure to cover the floor with

cardboard or hardboard to avoid floor damage. Always pull

the appliance straight out when moving it. Do not wiggle or

“walk” the appliance when trying to move it, as floor

damage could occur.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers

are heavy. Use both hands when removing them to avoid

dropping.

A. Screws (3)

B. Top hinge

C. Washer

D. Top spacer

E. Door

Attach the Overlay Frame

1. Gently pull back the gasket from all four corners. Pull back far

enough that two screws are visible in each corner (eight total

screws). Remove all eight screws.

2. Position the overlay frame so that the holes in the frame align

with the holes in the door liner.

NOTE: C-clamps are recommended to keep the overlay frame

and door liner aligned and to limit movement of the pieces.

3. Once all holes are aligned, fasten the custom frame to the

door using the screws provided as shown.

NOTE: The screws for this step are in a small plastic bag, located

in the interior of the beverage center.

Install the Door

IMPORTANT: To ensure proper operation, be sure to grease the

top hinge, top spacer and washer with petroleum jelly.

1. Using petroleum jelly, grease the bottom spacer hole and the

bottom hinge pin. Align the washer with the bottom spacer

hole.

2. Install the door by inserting the bottom hinge pin into the

bottom space hole. Be sure the washer stays in place. Slowly

lower the door straight down and evenly onto the bottom

hinge pin.

3. Close the door and check that it is aligned with the cabinet.

NOTE: Provide additional support for the door when moving the

hinges. Do not depend on the door magnets to hold the door in

place while you are working.

4. Using masking tape, secure the door to the cabinet before

installing the spacer, as shown.

5. Place the washer on the top spacer and align the holes.

Grease the top hinge pin, top spacer and washer with

petroleum jelly. Insert the top hinge pin into the washer and

top spacer.

6. Using a Phillips screwdriver and three screws, attach the top

hinge to the cabinet as shown.

7. Remove the masking tape from the door.

A. Hinge plate

B. Screws

C. Door

D. Gasket

A. Custom frame

B. Gasket

C.Door frame

Repeat on

thisside

A. Top spacer

B. Masking tape

A. Screws (3)

B. Top hinge

C. Washer

D. Top spacer

E. Door

F. O v erla y fra m e

Door Closing

Your beverage center has four leveling legs. If your beverage

center seems unsteady or you want the door to close more easily,

adjust the beverage center’s tilt using the instructions below.

1. Plug into a grounded 3 prong outlet.

2. Move the beverage center into its final location.

3. Turn the leveling legs to the right to lower the beverage center

or turn the leveling legs to the left to raise it. It may take

several turns of the leveling legs to adjust the tilt of the

beverage center.

NOTE: Having someone push against the top of the beverage

center takes some weight off the leveling legs. This makes it

easier to adjust the leveling legs.

4. Make sure that the door closes as easily as you like. If not, tilt

the beverage center slightly more to the rear by turning both

front leveling screws to the left. It may take several more

turns, and you should turn both leveling legs the same

amount.

BEVERAGE CENTER USE

Normal Sounds

Your new beverage center may make sounds that your old one

didn’t make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard

surfaces, such as the flooring and surrounding structures, can

make the sounds seem louder. The following describes the kinds

of sounds and what may be making them.

■Your beverage center is designed to run more efficiently to

keep your food items at the desired temperatures and to

minimize energy usage. The high efficiency compressor and

fans may cause your beverage center to run longer than your

old one. You may also hear a pulsating or high-pitched sound

from the compressor or fans adjusting to optimize

performance.

■Rattling noises may come from the flow of refrigerant or items

stored inside the beverage center.

■As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your beverage center.

■You may hear water running into the drain pan when the

beverage center is defrosting.

■You may hear clicking sounds when the beverage center

starts or stops running.

Using the Controls

The control panel for the beverage center is located on the

middle separator (mullion) of the beverage center. The control of

the beverage center has no mechanical parts or buttons. When

disconnected, the control panel displays nothing and may be

difficult to locate.

Turning Control On/Off

■The first time that the beverage center is plugged in, the

control will be in Cool Off mode. Cool On and Cool Off will be

the only options that display.

■Press COOL ON for 3 seconds to turn on the beverage

center. All menus and recommended temperature settings

will be displayed.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

beverage center.

Failure to do so can result in back or other injury.

■The left temperature and preset touch pads control the

temperature of the upper compartment.

■The right temperature and preset touch pads control the

temperature of the lower compartment.

Viewing Celsius Temperatures

■Press the F/C touch pad to toggle between displaying the

temperature in degrees Fahrenheit and degrees Celsius. The

corresponding indicator will illuminate.

Adjusting the Control

When the beverage center is turned On for the first time, the

temperature defaults to the recommended setting. There are two

adjustable temperature controls, with one for each compartment.

■To adjust set point temperatures, press “+” (plus) or “-”

(minus) until the desired temperature setting is reached.

NOTE: The set point for the beverage center is 37°F (3°C) for the

upper compartment and 50°F (10°C) for the lower compartment.

The set point range for the upper compartment is 33°F to 40°F

(0°C to 4°C) and 42°F to 64°F (5°C to 17°C) for the lower

compartment.

The control is set correctly when your beverages are as cold as

you like them.

NOTE: Wait at least 24 hours between adjustments for the

beverage center to acclimate. Recheck the temperatures before

making further adjustments.

Using Presets

For your convenience, your beverage center also has controls

that are preset to recommended storage temperatures for

specific beverages.

Pressing any preset option will set the temperature to the

recommended temperature for the specified beverages:

■Beverage: 34°F (1°C)

■Party: 37° (3°C)

■Red Wine: 64°F (17°C)

■White Wine: 50°F (10°C)

■Champagne: 46°F (7°C)

■Sweet Wine: 42°F (5°C)

Auto Light

The beverage center has a sensor that will turn on the interior

display light automatically when someone walks by. When motion

is no longer detected, the interior display light will go off after

2minutes.

■Press the Auto Light option to activate this feature.

■When the Auto Light is not activated, the interior display light

will only turn on when the door is opened.

NOTES:

■Leaving the light on for an extended period of time will slightly

increase the temperature of the beverage center.

■The light is an LED, which does not need to be replaced.

However, if the LED does not illuminate when the door is

opened, call Service to check the problem and replace if

necessary. See “Assistance or Service” for contact

information.

Sabbath Mode

Sabbath Mode is designed for the traveler or for those whose

religious observances require turning off the lights. By selecting

this feature, the temperature set points remain unchanged but

the control panel lights, interior lights, and control audio turn off.

For most efficient beverage center operation, it is recommended

to exit the Sabbath Mode when it is no longer required.

■Press and hold SABBATH for 3 seconds to turn on the

feature. After the 3-second countdown, the feature will

activate and all other displays will turn Off.

■Press and hold SABBATH for 3 seconds to turn off the feature

and turn on the display.

Door Open

If the door is open longer than 5 minutes, an alarm will sound

every 2 minutes until the door is closed or any control is pressed.

A. F/C touch pad

Over Temp Alarm

The Over Temperature feature is designed to let you know when

the beverage center temperature rises above 70°F (21°C) for

4 hours or longer. The audio alarm will shut off automatically

when the temperature returns to normal. To let you know an Over

Temperature condition occurred, the indicator light will continue

to flash until the Reset Alarm touch pad is pressed.

If the over temperature condition is still present when an Over

Temp reset is performed, the indicator light will continue to

reactivate every 4 hours until the beverage center temperature is

below 70°F (21°C).

NOTE: These features will not appear on your control unless your

beverage center is over temperature and the alarm requires a

reset.

Lock Mode

The Lock mode deactivates all other options to avoid any

changes being made to your desired temperature settings.

■To activate Lock mode, press and hold LOCK for 3 seconds.

After the countdown, all other displays will turn off and

become unavailable except Cool On, Cool Off and Lock.

Showroom Mode

This mode is used only when the beverage center is on display in

a retail store. If you unintentionally turn on Showroom mode, Cool

Off will light up on the display and the controls will appear to

work. Exit Showroom mode by pressing and holding COOL ON

and SABBATH at the same time for 3 seconds.

Beverage Shelf/Wine Racks

Remove and Replace the Top Shelf

1. Lift the front of the shelf up and away from the ledge on the

front of the shelf support.

2. Pull the shelf forward and lift it up and out of the shelf

supports.

3. Replace the shelf by inserting the back edge of the shelf

against the rear support in the back of the compartment.

4. Align the front of the shelf to the ledge on the front of the shelf

support.

5. Gently place the shelf into place.

Remove and Replace the Wine Racks

NOTE: When storing large bottles or magnums, remove the rack

directly above.

1. Pull the rack forward until it stops.

2. Lift up on the left-hand lever while pressing down on the

right-hand lever to release the rack. Pull the rack forward and

lift it up and out of the rack supports.

3. Replace the rack by inserting the rack into the supports and

sliding it toward the rear of the beverage center.

Stocking the Beverage Center

NOTES:

■For optimum wine storage, place white wines on the upper

rack of the beverage center and place red wines on the lower

rack of the beverage center.

■The wine racks can be stocked with the bottles facing either

direction, however, to optimize storage adjacent bottles

should be facing in opposite directions.

A. Lever

Inhaltsverzeichnis

Sprachen:

Andere KitchenAid Getränkespender Handbücher

KitchenAid

KitchenAid 2300276B Bedienungsanleitung

Beliebte Getränkespender Handbücher anderer Marken

PEGAS

PEGAS Evolution Bedienungsanleitung

Ugolini

Ugolini MT micro Bedienungsanleitung

Bunn

Bunn SLCA-7 Montageanleitung

Gekkeikan

Gekkeikan Sake Machine Bedienungsanleitung

Olympia

Olympia DH709 Bedienungsanleitung

Marco

Marco ECOSMART PB10 Bedienungsanleitung

Marvel

Marvel ML24BN Series Handbuch

Cecilware

Cecilware 2K-GB-LD Handbuch

Sure Vend

Sure Vend 673 Bedienungsanleitung

Cornelius

Cornelius 2 Flavor Post-Mix Cold Coffee Dispenser Quest... Bedienungsanleitung

Nostalgia Electrics

Nostalgia Electrics KEG7000SS Bedienungsanleitung

Bunn

Bunn LCR-3 HV Fehlerbehebungshandbuch

Servend

Servend SV-200 Bedienungsanleitung

EdgeStar

EdgeStar VBR440 Bedienungsanleitung

Cornelius

Cornelius A.B.S. Unit Bedienungsanleitung

CDS AUTOMATEN

CDS AUTOMATEN ML-16C2-C Bedienungsanleitung

Siemens

Siemens GA 3000 Gebrauchsanweisung

Cornelius

Cornelius FCB V4 Technische Daten