KitchenAid KDC-38 Bedienungsanleitung

DISHWASHER-SINK

COMBINATION

KDC-38 & KDS-38

INSTALLATION

INSTRUCTIONS

MR. INSTALLER: FINAL CHECK LIST

PLACEMENT OF DISHWASHER - SINK COMBINATION

0 1. Remove corrugated motor block packing from rear of unit after dishwasher is removed from skid.

n 2. Properly positioned-level, aligned and square with cabinet opening.

n 3. Anchored securely, either to cabinet or floor.

n 4. Installation debris removed from under dishwasher.

ELECTRICAL CONNECTION

n 1. Separate 115 volt, 60 hertz, 1 phase branch circuit with a 15 ampere minimum protected by a

maximum of 15 ampere fuse size.

n 2. Dishwasher properly grounded.

n 3. All connections in conformance with local electrical code.

PLUMBING

0 1. Water supply at dishwasher: 20 to 120 P.S.I. pressure, temperature of 140” F.

to 160” F. and l/2” O.D. (min.) copper tube.

n 2. Drain lines at least 5/8” O.D. copper tubing or equivalent without drain air gap

and with no tight bends (kinks) or other restrictions to prevent complete draining.

0 3. Drain lines at least g/16” I.D. copper tubing or equivalent with drain air gap

and with no tight bends (kinks) or other restrictions to prevent complete draining.

n 4. Compliance with all aspects of local plumbing code.

n 5. Make sure drain hose does not touch any electrical components or terminals.

OPERATIONAL

Cl 1. All internal packing material, labels, and foam door pads removed.

Place detergent in both compartments of detergent dispenser, close cover(s) and

operate dishwasher through complete “Normal Cycle,” Note: KDC has cover over

only one of two compartments.

Check: Proper Fill-Water level approximately l-1/2” below centerline of 4 Way Hydro

Sweep hub. Complete Drain.

Detergent Dispenser-must operate automatically and completely dispense

detergent.

Dishracks, for freedom of movement and adjustment.

THANK YOU MR. INSTALLER:

1. Complete Installation Check

List.

2. Leave all literature (Incl. Check List) for customer.

3. Notify dealer that electrical work and plumbing are completed.

FORDETAILED

INffRUCTIONf, FOLLOWMETHODSDESCRIBEDIN THISFOLDER

IMPORTANT: Read Before Installing to Save Time, Work,

assure proper performance, and owner’s warranty protection.

ELECTRICAL SPECIFICATIONS

Voltage & Frequency --- 115 volts-60 hertz

Operating load ------- 13.5 amperes - KDS-38

7.9 amperes - KDC-38

Maximum Fuse Size ---- 15 amperes

CAUTION: Avoid getting white lead or lubricant

inside new joints. Hot water fill line must be flushed

of foreign matter before connection to dishwasher

fill valve. A hand shut off valve (not furnished) should

be located in an easily accessible area adjacent to the

dishwasher.

Wiring must conform to local code and/or Nat.

Electrical Code.

Plumbing must conform to local code. Use l/2” O.D. ature at dishwasher should be 140°F. to 160°F. A

(min.) copper tube for water line. Dishwasher has 5/8” I.D. drain hose is furnished for connection to an

318” I.P.S. Internal thread at valve. A 90” air gap, waste disposer or the Drain ‘7.” Drain “T” is

compression ell (furnished) should be used to furnished. Air Gap and Rinse Agent Kit accessories,

connect tubing to valve. Water flow pressure at if required, are available from your dealer or distrib-

dishwasher to be 20 PSI to 120 PSI. Water temper- utor.

INSTALLATION INSTRUCTIONS

Locate top of lower panel just below evaporation channel

support. Insert panel flange under evaporation channel

support ends “A” and push up to engage top of panel. Lift

up lower bottom flange of panel, place flange “B” over frqnt

face of frame and push in. Assemble lock washer “D” under

head of one screw to ground dishwasher. Fasten panel with

two screws “C” furnished. If a wood or laminate front is to

be used and these panels are not immediately available, use

back-up panel furnished with trim kit. Stainless steel trim

should be used to assemble wood or laminate when available.

Reverse procedure when removing lower panel.

To establish a reference line for purposes of

providing plumbing and electrical connections

to the dishwasher, measure 21” from the wall.

(This is the front edge of dishwasher kick

panel. There is a 3” toe space from the front

of the kick panel to the front edge of the

dishwasher with a standard metal front

panel). For corner installation, allow 2” clear-

ance for adjacent cabinet.

SHADED AREA SHOULD BE FREE

OF ALL PLUMBING AND ELECTRICAL CONNECTIONS

SINK

CABINET

LOCATING bf

ore setting dishwasher in place, run CAUTION: No other outlets or

WIRING

individual 15 amp. minimum branch appliances should be placed on this

circuit with grounded electrical cable. circuit.

CONNECTING FILL LINE

DISHWASHER attaching to dishwasher

:24

114”

Locate hot and cold water lines as in Fig. 3.

\\I

All sweat fittings for l/2” O.D. copper

tubing must be sweat into place before

SINK CABINET

to prevent excess

24”’

/ When connecting fill line to dishwasher fill valve,

do NOT overtighten fitting which could damage fill

valve. Make sure line has no sharp bends (5” min. bend

radius suggested) that may produce kinks which might

restrict water flow. Connect all water fill lines making

certain that there is a hand shut off valve (A) in the hot

water supply line to the dishwasher as illustrated in Fig.

3. For servicing dishwasher, it is recommended a union

be installed between shut off valve and fill valve.

NOTE: Do Not Kink Drain Hose.

Minimum Size For All Dishwasher Drains Is 9/16” I.D.

B-5/8” 0.0. COPPER TUBING-NOT FURNISHED.

C-An adapter may be required if air gap is used (not furnished).

D-Flexible drain connection, where permitted by local plumbing codes must be g/16” I.D. minimum.

FIG. 4

CONNECTING

Dishwasher has pump out drain.

Except during drain periods,

drain valve is closed thus pro-

tecting the dishwasher from

normal back flow from drain

line. Connect dishwasher drain to

meet local code. Do not install

DRAIN LINE

check valve in drain line. See disposer, be sure to remove the

suggested installation (Fig. 4 and knock-out (or threaded) plug in

5). Where drain air gap is re- the disposer to insure proper

quired by local code, use type drainage.

approved. Opening is provided CAUTION: Make sure drain hose

on top of sink. When connecting does not touch any electrical

dishwasher drain to a food waste components or terminals.

FIG. 5

Dotted lines indicate sink tops with and without

disposer.

FINAL POSITIONING

FIG. 6

Remove corrugated motor block packing after dishwasher is

removed from skid. With unit in position, make sure it is level.

CAUTION: Since dishwasher is attached to sink cabinet, any

required dishwasher leveling feet adjustment, should be done with

extreme care to avoid possible misalignment of sink cabinet doors.

Starting from the center of the dishwasher-sink, adjust the front

and rear leveling feet (A, Fig. 4), then outside leveling feet.

Cabinet doors should be perpendicular with cabinet opening and

level across the top. If necessary, dishwasher leveling feet should

be readjusted to attain correct cabinet door alignment. Cabinet

leveling feet (E, Fig. 4) must be adjusted to complete final

leveling. It may be necessary to anchor dishwasher to floor using

l/4” lag bolts or screw in hole provided. If required, use molding

(furnished by installer) to cover any gap on either side of unit.

IMPORTANT FOR SAFETY

CONNECT TO ELECTRICAL POWER AND GROUND

A-Remove junction box on dishwasher. B-Install approved connector (not

furnished). C-Connect power cable white lead to white lead and black lead

to black lead with adequate insulation or wire nuts and ground wire under

green ground screw or lug. Reinstall junction box.

When house wiring is aluminum, use U.L. approved aluminum to copper

connectors.

The dishwasher must be properly grounded before operating by connecting

the chassis ground lug terminal to a suitable ground complying with National

Electrical Code and/or local electrical code.

FIG. 7

TESTING INSTALLATION

Remove installation debris from under dishwasher, foam door pads on each side and near top of

tank, and all internal packing material and labels. NOTE: DO NOT REMOVE DOOR BUMPER.

Turn on electrical power and water supply. Then, push door handle down to lock

Turn Action Indicator clockwise to the OFF position and press “Normal Cycle” button on

position (Custom model). On Superba model, Custom model. Press “Sam-Cycle” button on

press “Cancel-Drain” button; timer will Superba. Run dishwasher through the com-

advance to “OFF” automatically. Lift door plete cycle to make certain it is operating

handle. Wait for Timer to automatically reset

itself (necessary for initial installation test of properly. Turn off electrical power and check

for leaks. If no leaks, turn on electrical power.

Superba only).

CAUTION

For installation when the dishwasher is to be left unused in

freezing temperatures: Turn off electrical power. Shut off water

supply at the hand valve. Remove lower panel. Disconnect both

inlet and outlet lines at the DRAIN valve. This permits water to

drain from the dishwasher tank, pump and drain line. Dis-

connect both the inlet and outlet lines at the FILL valve. Make

provisions to control water drained from unit. Reinstall lower

panel. Turn on electrical power. Then, push door handle down

to lock position and push “Normal Cycle” button. Let

dishwasher run through first pre-rinse only (approximately four

minutes) to drain all water trapped in the dishwasher. Turn off

electricity. To complete installation later:

Connect drain and fill valves-both inlet and outlet.

Reinstall lower panel.

Turn on water and electrical supply. Then push

button for cycle desired.

DETAILS AND CONNECTIONS

KDC-38 & KDS-38

BASIC DIMENSIONS

KITCHENAID DIVISION

\HOBAFtT(

TROY. OHIO 45374

FORM 12194D (Rev. 8-78) (Supsds. F. 12194C. 4-78) PRINTED IN U.S.A.

-597

7g.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KitchenAid Spülmaschine Handbücher

KitchenAid

KitchenAid KUDD03DTPA3 Bedienungsanleitung

KitchenAid

KitchenAid KUDW03CTWH2 Bedienungsanleitung

KitchenAid

KitchenAid Architect Series II KUDE60FXSS Montageanleitung

KitchenAid

KitchenAid KDC-40 Bedienungsanleitung

KitchenAid

KitchenAid KUDI01TJ Bedienungsanleitung

KitchenAid

KitchenAid KUDJ01TJ Bedienungsanleitung

KitchenAid

KitchenAid Sculptura KUDV24SE Bedienungsanleitung

KitchenAid

KitchenAid KUDS03FTPA3 Bedienungsanleitung

KitchenAid

KitchenAid KDTE204EPA Bedienungsanleitung

KitchenAid

KitchenAid Briva KIDS36EP Bedienungsanleitung

KitchenAid

KitchenAid KUDC02IR Benutzerhandbuch

KitchenAid

KitchenAid KUDS011L Bedienungsanleitung

KitchenAid

KitchenAid KUDS50FVBL0 Bedienungsanleitung

KitchenAid

KitchenAid KDTM354DSS Bedienungsanleitung

KitchenAid

KitchenAid 528534 Bedienungsanleitung

KitchenAid

KitchenAid KUDS03CTBL2 Bedienungsanleitung

KitchenAid

KitchenAid KUDS03STBL2 Bedienungsanleitung

KitchenAid

KitchenAid Superba 4KUDS220T Bedienungsanleitung

KitchenAid

KitchenAid KUDC20CVBL - Kitchen-Aid Dishwasher Bedienungsanleitung

KitchenAid

KitchenAid KUDC03ITBL3 Bedienungsanleitung

KitchenAid

KitchenAid KUDS01FL Bedienungsanleitung

KitchenAid

KitchenAid KUDR25SH Bedienungsanleitung

KitchenAid

KitchenAid KUDS02SR Bedienungsanleitung

KitchenAid

KitchenAid KUDU03STBL0 Bedienungsanleitung

Beliebte Spülmaschine Handbücher anderer Marken

Electrolux

Electrolux ESI5211LOX Bedienungsanleitung

Brandt

Brandt BDJ424DB Bedienungsanleitung

Asko

Asko DSD767UXXL.AU Bedienungsanleitung

Beko

Beko DFN26210W Bedienungsanleitung

NEFF

NEFF S153ITX00E Technisches Datenblatt

Midea

Midea SV 4.45 wi Bedienungsanleitung

LG LDF7932 Bedienungsanleitung

Gorenje

Gorenje GV63214 Bedienungsanleitung

Hotpoint

Hotpoint HDA1100ZWH Service-Handbuch

Blomberg

Blomberg LDFN2240W Bedienungsanleitung

AEG

AEG FFB83836PM Bedienungsanleitung

Cylinda

Cylinda DM3220RFD Bedienungsanleitung

Atag

Atag DW8214MB Bedienungsanleitung

GE GLD8000 Series Bedienungsanleitung

Siemens

Siemens SN23HI02KE Technisches Datenblatt

Omega

Omega ODW717X Bedienungsanleitung

BORETTI

BORETTI BVW-683 Bedienungsanleitung

Siemens

Siemens SN 56N591 Bedienungsanleitung