KitchenAid 5KSM150PSP Series Bedienungsanleitung

5KSM150PSP Series

5K45SSP Series

5KSM6583P Series

W11371189A.indd 1 6/6/2019 6:34:00 PM

12 13

14 15

1Motor Head (locking lever not shown)

2Attachment Knob

3Attachment Hub

4Motor Head

5Speed Control Lever

6Beater Height Adjustment screw

(not shown)

7Bowl Clamping Plate

8Bowl**

9Beater Shaft

10 Pouring shield*

11 3 L Stainless Steel Bowl*

12 Flat Beater

13 Flex Edge Beater*

14 Wire Whip

15 Dough Hook

PARTS AND FEATURES

*Included with select models only. Also available as an optional accessory.

**The bowl design and material depend on the Stand Mixer model.

TILT HEAD STAND MIXER PARTS AND ACCESSORIES

W11371189A.indd 2 6/6/2019 6:34:01 PM

ENGLISH

PARTS AND FEATURES

BOWL LIFT STAND MIXER PARTS AND ACCESSORIES

12 13

14 15

1Motor Head

2Speed Control Lever

3Beater Height Adjustment screw

4Bowl Support

5Locating Pins

6Stainless Steel Bowl**

7Beater Shaft

8Bowl Lift Lever (not shown)

9Attachment Knob

10 Attachment Hub

(see the “Optional Attachments”

section)

11 Pouring Shield*

12 Flat Beater

13 Flex Edge Beater*

14 Wire Whip

15 Dough Hook

* Included with select models only. Also available as an optional accessory.

**Capacity and handle design vary by model.

W11371189A.indd 3 6/6/2019 6:34:02 PM

PRODUCT SAFETY

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always

be followed, including the following:

1. Read all instructions. Misuse of appliance may result in personal injury.

2. To protect against risk of electrical shock, do not put Stand Mixer in water or

other liquid.

3. This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

4. Children should be supervised to ensure that they do not play with the

appliance.

5. Turn the appliance OFF, then unplug from the outlet when not in use, before

assembling or disassembling parts, and before cleaning. To unplug, grasp

the plug and pull from the outlet. Never pull from the power cord.

6. Avoid contacting moving parts. Keep hands, hair, and clothing, as well

as spatulas and other utensils, away from beater during operation to reduce

the risk of injury to persons and/or damage to the Stand Mixer.

7. Do not operate any appliance with a damaged cord or plug or after the

appliance malfunctions, or is dropped or damaged in any manner. Contact

the manufacturer at their customer service telephone number for information

on examination, repair, or adjustment.

8. If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

9. The use of accessories or attachments not recommended or sold by the

manufacturer may cause fire, electric shock or injury.

10. Do not use the Stand Mixer outdoors.

W11371189A.indd 4 6/6/2019 6:34:02 PM

ENGLISH

SAVE THESE INSTRUCTIONS

PRODUCT SAFETY

11. Do not let the cord hang over the edge of table or counter.

12. Remove the beaters, wire whip, or dough hook from the Stand Mixer before

washing.

13. Do not leave the Stand Mixer unattended while it is operating.

14. Refer to the “Care and Cleaning” section for instructions on cleaning the

surfaces in contact with food.

15. This appliance is intended to be used in household and similar applications

such as:

- staff kitchen areas in shops, offices or other working environments;

- farmhouses;

- by clients in hotels, motels and other residential type environments;

- bed and breakfast type environments.

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into an earthed outlet.

Do not remove earth prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these

instructions can result in

death, fire, or electrical shock.

5KSM150PSP Series

Wattage: 300 W

Volts: 230V

Hertz: 60 Hz

5K45SSP Series

Wattage: 275 W

Volts: 230V

Hertz: 60 Hz

5KSM6583P Series

Wattage: 500 W

Volts: 230V

Hertz: 60 Hz

NOTE: If the plug does not fit in the

outlet, contact a qualified electrician. Do

not modify the plug in any way. Do not

use an adapter.

Do not use an extension cord. If the

power supply cord is too short, have a

qualified electrician or service technician

install an outlet near the appliance.

W11371189A.indd 5 6/6/2019 6:34:02 PM

SPEED CONTROL GUIDE

Speed Action Description

1Stir For slow stirring, combining, mashing, starting all mixing

procedures. Use to add ﬂour and dry ingredients to batter

and to add liquids to dry ingredients. Do not use Speed 1

to mix or knead yeast doughs.

2Slow mixing For slow mixing, mashing, faster stirring. Use to mix and

knead yeast doughs, heavy batters and candies, start

mashing potatoes or other vegetables, cut shortening into

ﬂour, or mix thin or splashy batters.

4Mixing, beating For mixing semi-heavy batters, such as cookies. Use to

cream sugar and shortening and to add sugar to egg

whites for meringues. Medium speed for cake mixes. Use

with attachments: Food Grinder, Rotor Slicer/Shredder, and

Fruit/ Vegetable Strainer.

6Beating, creaming For medium fast beating (creaming) or whipping. Use

to ﬁnish mixing cake, doughnut, and other batters. High

speed for cake mixes. Use with Citrus Juicer attachment.

8Fast beating,

whipping

For whipping cream, egg whites, and boiled frostings.

10 Fast whipping For whipping small amounts of cream and egg whites. Use

with Pasta Maker and Grain Mill attachments.

Note:The speed control can be set to obtain speeds 1, 3, 5, 7, and 9 if a finer adjustment is

required. Do not exceed Speed 2 when preparing yeast doughs as this may cause damage to

the Stand Mixer.

GETTING STARTED

Accessories Use to mix Suggested items

Flat Beater

Flex Edge Beater

Normal

to heavy

mixtures

Cakes, creamed frostings, candies, cookies,

biscuits, pie pastry, meatloaf, mashed potatoes

Wire Whip

Mixtures

that need air

incorporated

Eggs, egg whites, heavy cream, boiled frostings,

sponge cakes, mayonnaise, some candies

Dough Hook

Mixing and

kneading yeast

doughs

Breads, rolls, pizza dough, buns, coffee cakes

CHOOSING THE RIGHT ACCESSORY

W11371189A.indd 6 6/6/2019 6:34:03 PM

ENGLISH

PRODUCT USAGE

ASSEMBLING/DISASSEMBLING YOUR TILT HEAD STAND MIXER

To attach bowl:

1. Turn speed control to 0 (off).

2. Tilt motor head back.

3. Place bowl on bowl clamping plate.

4. Turn bowl gently in clockwise direction

(see illustration above).

5. Place the pouring shield on bowl.*

To remove bowl:

1. Turn speed control to 0 (off).

2. Tilt motor head back.

3. Turn bowl in counterclockwise direction.

To attach Flat Beater, Wire Whip, Dough

Hook or Flex Edge Beater*:

1. Turn speed control to 0 (off) and

unplug.

2. Raise motor head.

3. Slip beater onto beater shaft and press

upward as far as possible.

4. Turn beater to right, hooking beater

over pin on shaft.

To remove Flat Beater, Wire Whip, Dough

Hook or Flex Edge Beater*:

1. Turn speed control to 0 (off) and

unplug.

2. Raise motor head.

3. Press beater upward as far as possible

and turn left.

4. Pull beater from beater shaft.

To lock motor head in raised position:

1. Push locking lever up into unlock

position and hold.

2. Tilt motor head back.

3. Move locking lever into lock position.

To lock motor head in operating position:

1. Turn speed control to 0 (off) and

unplug.

2. Unlock the motor head and move it

down.

3. Lock the head to keep it down

4. Before mixing, test lock by attempting

to raise the motor head.

NOTE: Motor head should always

be kept in lock position when using Stand

Mixer.

To operate speed control:

1. Speed control lever should always be

set on lowest speed for starting, then

gradually moved to desired higher

speed to avoid splashing ingredients

out of bowl. See “Speed control

guide.”

KitchenAid

St.Joseph,Michigan,USA

12 4 6 810

OFF ON

*Included with select models only. Also available as an optional accessory.

W11371189A.indd 7 6/6/2019 6:34:03 PM

PRODUCT USAGE

ASSEMBLING/DISASSEMBLING YOUR BOWL LIFT STAND MIXER

*Included with select models only. Also available as an optional accessory.

Electrical Shock Hazard

Plug into an earthed outlet.

Do not remove earth prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these

instructions can result in

death, fire, or electrical shock.

To Attach Bowl

1. Turn speed control to “0” (Off).

2. Unplug Stand Mixer or disconnect power.

3. Place bowl lift lever in down position.

4. Fit bowl supports over locating pins.

5. Press down on back of bowl until bowl pin

snaps into spring latch. Raise bowl before

mixing.

6. Plug into an earthed outlet

or reconnect power.

To Remove Bowl

1. Turn speed control to “0” (Off).

2. Unplug Stand Mixer or disconnect power.

3. Place bowl lift lever in down position.

4. Remove ﬂat beater, wire whip, or dough

hook.

5. Grasp bowl handle and lift straight up and

off locating pins.

To Raise Bowl

1. Rotate lever to straight-up position.

2. Bowl must always be in raised, lock

position when mixing.

To Lower Bowl

1. Rotate lever back and down.

To Attach Flat Beater, Wire Whip, Dough

Hook or Flex Edge Beater*:

1. Turn speed control to “0” (Off).

2. Unplug Stand Mixer or disconnect power.

3. Slip ﬂat beater

on beater shaft

and press upward

as far as possible.

4. Turn beater to right, hooking beater over

the pin on shaft.

5. Plug into an earthed outlet or reconnect

power.

To Remove Flat Beater, Wire Whip, Dough

Hook or Flex Edge Beater*:

1. Turn speed control to “0” (Off).

2. Unplug Stand Mixer or disconnect power.

3. Press beater upward as far as possible and

turn left.

4. Pull beater from beater shaft.

5. Plug into an earthed outlet or reconnect

power.

Stand Mixer Speed Control and Lever

Guard

The Stand Mixer has a feature that

minimizes splash-out by starting the

mixer slowly before increasing to the

selected speed. To further reduce the

potential for splash-out, always begin

mixing using speed 1, then gradually

move to higher speeds as needed.

See “Speed Control Guide.”

Auto-Reset Motor Protection

If the Stand Mixer stops due to overload,

slide the speed control lever to “0” (Off).

After a few minutes, the stand mixer will

automatically reset. Slide the speed control

lever to the desired speed and continue

mixing. If the Stand Mixer does not restart,

see “Troubleshooting Guide.”

W11371189A.indd 8 6/6/2019 6:34:04 PM

ENGLISH

PRODUCT USAGE

Your Stand Mixer is adjusted at the factory

so that the flat beater just clears the

bottom of the bowl. If for any reason the

flat beater strikes the bottom of the bowl

or is too far away from the bowl, clearance

can be corrected as follows:

Tilt head

1. Lift motor head.

2. Turn screw (A) slightly to the left to raise

flat beater and to the right to lower flat

beater.

3. Make adjustment with flat beater, so it

just clears surface of bowl.

Bowl lift

1. Place bowl lift

handle in down

position.

2. Turn screw (B)

slightly to the

left to raise

flat beater and to the right to lower flat

beater.

3. Make adjustments with flat beater,

so it just clears surface of bowl.

NOTE: Flat beater must not strike on

bottom or side of bowl when properly

adjusted. If beater or wire whip is

adjusted too close so that it strikes

bottom of bowl, coating may wear off of

beater or wires may wear through on wire

whip.

Scraping sides of bowl may be necessary

under certain conditions regardless of

beater adjustment. Stand Mixer must be

stopped to scrape bowl or damage to

Stand Mixer may occur.

BEATER TO BOWL CLEARANCE

To attach Pouring Shield*:

1. Turn speed control to “0” (Off).

2. Unplug Stand Mixer or disconnect power.

3. Attach Flat Beater, Wire Whip, Dough

Hook or Flex Edge Beater* and Bowl.

Front the front

of the mixer,

slide the

Pouring Shield*

over the bowl

until it is

centered.

4. The bottom rim of the pouring shield*

should fit within the bowl.

W11371189A.indd 9 6/6/2019 6:34:04 PM

Insert attachment into attachment hub,

making certain that attachment power

shaft ﬁts into the square attachment hub

socket.

Tighten the attachment knob by turning it

clockwise until the attachment is secured

to the Stand Mixer.

OPTIONAL ATTACHMENTS

USING THE POURING SHIELD*

For best results, rotate the Pouring

Shield* so the motor Head Covers the

U-shaped gap in the shield. The pouring

chute will be just to the right of the

Attachment Hub as you face the mixer

Pour ingredients into the bowl through

the pouring chute.

*Included with select models only. Also available as an optional accessory.

Turn the Stand Mixer to “0” (Off) and

then unplug the stand mixer.

KitchenAid offers a wide range of optional attachments such as the Spiralizer, Pasta

Cutters, or Food Grinder that may be attached to the Stand Mixer attachment power hub

as shown below.

Remove the attachment hub cover.

W11371189A.indd 10 6/6/2019 6:34:05 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KitchenAid Mischer Handbücher

KitchenAid

KitchenAid KSM95BU0 Bedienungsanleitung

KitchenAid

KitchenAid KSM95SM - Ultra Power Stand Mixer Bedienungsanleitung

KitchenAid

KitchenAid 4KP26M1XBS4 Bedienungsanleitung

KitchenAid

KitchenAid KP2671XAC - Professional Stand Mixer Bedienungsanleitung

KitchenAid

KitchenAid KSM95GR - Ultra Power Stand Mixer Bedienungsanleitung

KitchenAid

KitchenAid 5K45 Series Bedienungsanleitung

KitchenAid

KitchenAid KSM170 Installationsanleitung

KitchenAid

KitchenAid KP26M8XMC5 Bedienungsanleitung

KitchenAid

KitchenAid KSMc50 Bedienungsanleitung

KitchenAid

KitchenAid G Bedienungs- und Wartungshandbuch

KitchenAid

KitchenAid 5KSMC895Z Bedienungsanleitung

KitchenAid

KitchenAid Mixer Kurzanleitung

KitchenAid

KitchenAid 5K45SSN Bedienungsanleitung

KitchenAid

KitchenAid 5K45SS Bedienungsanleitung

KitchenAid

KitchenAid KSM3311XFW0 Bedienungsanleitung

KitchenAid

KitchenAid 5KFE35T Bedienungsanleitung

KitchenAid

KitchenAid CommerCial mixer Bedienungsanleitung

KitchenAid

KitchenAid KSM8990ER Bedienungsanleitung

KitchenAid

KitchenAid ACCOLADE 400 Kurzanleitung

KitchenAid

KitchenAid KEA25A Bedienungsanleitung

KitchenAid

KitchenAid 9708307C Bedienungsanleitung

KitchenAid

KitchenAid KSM7586PCA Bedienungsanleitung

KitchenAid

KitchenAid *521.004 Bedienungsanleitung

KitchenAid

KitchenAid Professional 600 Series Kurzanleitung

Beliebte Mischer Handbücher anderer Marken

Bosch

Bosch GRW 9 Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman WM45E Leitfaden

Jay-Lor

Jay-Lor 5050 Bedienungsanleitung

Sunbeam

Sunbeam FPSBSM210X Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman MC94S Leitfaden

Thinky

Thinky ARE-250 Bedienungsanleitung

Midas

Midas XL4 Bedienungsanleitung

bianco

bianco PURO 4 Bedienungsanleitung

Paso

Paso DAG9200 Bedienungsanleitung

Sima

Sima SFX-9A Bedienungsanleitung

better chef

better chef IM-815WC Montageanleitung

ALLEN & HEATH

ALLEN & HEATH GR1 Bedienungsanleitung

Lacor

Lacor 69083 Technisches Datenblatt

M-Audio

M-Audio Midiman SAM Bedienungsanleitung

Buffalo

Buffalo CP921 Bedienungsanleitung

Pentair

Pentair HYPRO Cleanload 3376-0870 Betriebsanleitung

Cuisinart

Cuisinart SM50WHE Bedienungsanleitung

Hobart

Hobart HCM-300 Bedienungsanleitung