KMC Controls FlexStat Bedienungsanleitung

FlexStat 1 Quick Reference Guide

Quick Reference Guide

DRAFT

NOTE: Watermark is

on nonwritable DRAFT

Watermark layer. Turn the

layer off or delete layer

to remove from the nal

document.

FlexStat

Controller/Sensor/Thermostat

Contents

Navigation .......................................................1

Room Temperature Setpoint Adjustment ..........1

Main Menu and Settings ..................................2

Schedules.........................................................2

Heat/Cool, Fan, Occupancy, and Override ......2

Navigation

Navigate the menus and change seings by press-

ing a combination of various arrow buons and the

(center round) Enter buon. Push the:

• Enter buon to select and/or exit value editing.

• Up or Down buon to move among entries.

• Right or Left buon to move among value elds.

• Left buon to return to the Home screen.

NOTE: Access to various functions may require a

password.

NOTE: See the FlexStat Operation Guide for

complete details on FlexStat conguration.

Room Temperature Setpoint Adjustment

From the Home (temperature display) screen, press

the Up or Down arrow buon once to view the exist-

ing setpoint.

To temporarily change the setpoint, press the Up

or Down arrow buon repeatedly until the desired

seing is displayed and press Enter. (If Enter is not

pressed, the display will return to the Home screen

after about ten seconds and the new setpoint value

will still be saved.) The new setpoint will hold until

the next schedule change.

To permanently change the setpoint for occupied

mode, go to the Setpoints section under the Main

Menu. (In the Setpoints menu, heating/cooling set-

points/setbacks and deadband can be changed with,

if required, the correct password access.)

WED 9/3 5:43 PM

COOL:

OCC:

FAN:

HUM: 31%RH

MAIN MENU

ABOUT

ADVANCED

ALARM

DATE/TIME

SCHEDULE

SETPOINTS

SYSTEM

SCHEDULE

ENTIRE WEEK [MON–SUN]

WEEKDAYS [MON–FRI]

WEEKEND [SAT–SUN]

INDIVIDUAL DAYS

HOLIDAYS

ENTIRE WEEK

2: 5:15:00 PM OFF

[—>] DELETES ENTRY

7:30:00 AM ON

SYSTEM MODE

SYSTEM ENABLE: AUTO

OCCUPANCY OVERRIDE

OCC OVERRIDE: OFF

FAN MODES

UNOCC:

OCC: AUTO

AUTO

Override

Setpoint Adjustment

Home Screen

Override Screens

Conﬁguration

Conﬁguration Screens

Right

(Menu)

Left

(Override)

Down (Setpoint)

Up (Setpoint)

FlexStat 2 Quick Reference Guide

KMC Controls, Inc.

19476 Industrial Drive

New Paris, IN 46553

574.831.5250

www.kmccontrols.com

[email protected]

(Speciﬁcations, design, and operation are subject to change without notice)

Schedules

SCHEDULE

ENTIRE WEEK [MON–SUN]

WEEKDAYS [MON–FRI]

WEEKEND [SAT–SUN]

INDIVIDUAL DAYS

HOLIDAYS

ENTIRE WEEK

2: 5:15:00 PM OFF

[—>] DELETES ENTRY

7:30:00 AM ON

The factory default schedule is always occupied

(ON). To modify the schedule for mixed occupied

(ON) and unoccupied (OFF) times, select Schedules

in the Main Menu and press:

1. Right/Left to move among days and Enter to

select.

2. Up/Down to move among entries and Enter to

select and edit.

3. Right/Left to move among value elds.

4. Up/Down to increment/decrement value.

5. Enter to exit value editing.

6. Left to move back to days or back one page.

NOTE: If a day of a week (e.g., Friday) has a

dierent schedule than the rest, using the

Weekdays menu rst and then modifying

that one day in the Individual Days menu

may be easier (two entries) than entering

schedules for each day separately in the

Individual Days menu (ve entries).

NOTE: The last overlapping entry overrides

any other. For example, suppose the

WEEKDAYS menu is used to set all

weekdays for 7:00 AM ON and 5:00 PM

OFF, and then the INDIVIDUAL DAYS

menu is used to add some additional

evening meeting ON times for Tuesday

and Wednesday. If the WEEKDAYS menu

is later used to change the ON time from

7:00 to 7:15, schedules for all the individual

week days will be reset to conform to

what appears in the WEEKDAYS menu

and any special times for individual days

will be erased. (Special day schedules will

then need to be added again through the

INDIVIDUAL DAYS menu).

The Holiday entries will override the normal

occupied weekly schedule entries and keep those

days’ seings at their setback values. (Setback values

are entered in the Setpoints section of the Main

Menu.)

HOLIDAYS

HOL1:

HOL2: MAR 21 2009

HOL3: MAY 26 2009

HOL4: JULY 4 2009

HOL5: SEPT 1 2009

HOL6: NOV 27 2009

HOL7: NOV 28 2009

JAN 1 2009

NOTE: See the FlexStat Operation Guide for more

operation details.

Main Menu and Settings

From the Home (temperature display) screen, press

the Right arrow buon to enter the Main Menu.

Heat/Cool, Fan, Occupancy, and Override

When the fan is commanded to run, the animated

FAN icon on the display rotates (if programmed to).

When the fan command stops, the fan icon is mo-

tionless.

The OCC icon shows a sun when in Occupied mode

and a quarter moon when in Unoccupied mode.

HEAT or COOL will show (and be animated when

there is an active command to move the room tem-

perature toward the setpoint via mechanical heating/

cooling or an economizer), depending on the current

mode. This can also be turned OFF.

To override these modes from the Home (tempera-

ture display) screen, press the Left arrow buon.

Press Up or Down to get to the desired line and then

Enter (twice) to edit the mode seing. Press Left to

exit to Home.

NOTE: Seings and adjustments may require a

password.

Andere Handbücher für FlexStat

Inhaltsverzeichnis

Andere KMC Controls Thermostat Handbücher

KMC Controls

KMC Controls CTE-5202 Benutzerhandbuch

KMC Controls

KMC Controls FlexStat Bedienungsanleitung

KMC Controls

KMC Controls CTC-4001 Bedienungsanleitung

KMC Controls

KMC Controls CTE–5101 Bedienungsanleitung

KMC Controls

KMC Controls CTE-1005 Bedienungsanleitung

KMC Controls

KMC Controls FlexStat BACnet Bedienungsanleitung

KMC Controls

KMC Controls BAC-19 FlexStat Series Benutzerhandbuch

KMC Controls

KMC Controls CTE-5201 Betriebsanleitung

KMC Controls

KMC Controls CTC–5500 Series Bedienungsanleitung

KMC Controls

KMC Controls FlexStat BAC-10000 Series Bedienungsanleitung

KMC Controls

KMC Controls FlexStat Bedienungsanleitung

KMC Controls

KMC Controls FlexStat BACnet Bedienungsanleitung

KMC Controls

KMC Controls NetSensor KMD-1101 Original Betriebsanleitung

KMC Controls

KMC Controls FlexStat Benutzerhandbuch

KMC Controls

KMC Controls CTE-5001 Bedienungsanleitung

KMC Controls

KMC Controls CTE-5202 Betriebsanleitung

KMC Controls

KMC Controls CTC-1653 Bedienungsanleitung

KMC Controls

KMC Controls BAC-1xx63 Series Bedienungsanleitung

KMC Controls

KMC Controls FlexStat Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung