Kodak I810 - Scanner Firmware - PC Bedienungsanleitung

User’s

Guide

A-61169

Part No. 9E3959

CAT No. 129 5237

i800 Series Scanners

January 2005 1

Safety and Installation Information for the Kodak i800 Series Scanners

IMPORTANT: Equipment shall be installed by qualified personnel.

WARNING: Dangerous voltage. Disconnect the main power before installation.

WARNING: Before changing a lamp, always power down the scanner and let it cool a minimum

of 10 minutes before proceeding (see Warning Labels below).

CAUTION: Hot surface, avoid contact

POZOR: Horký povrch -- nedotýkat se

DIKKAT: Hareketli parçalar, dokunmayin

CAUTION: Moving parts, avoid contact

POZOR: Pohybující sečástie -- nedotýkat se

DIKKAT: Sicak yüzey, dokunmayin

User Precautions

Users and their employer need to observe the common sense precautions applicable to the operation of

any machinery. These include, but are not limited to, the following:

• Do not wear loose clothing, unbuttoned sleeves, etc.

• Do not wear loose jewelry, bracelets, bulky rings, long necklaces, etc.

• Hair length should be kept short, using a hair net if needed, or tying long hair up in a bundle.

• Remove all other loose objects from the area that could be drawn into the machine.

• Take sufficient breaks to maintain mental alertness.

• Follow the recommended Kodak cleaning procedures. Do not use air, liquid or gas spray cleaners.

These cleaners only displace the dust, dirt or debris to another location within the scanner, which

could cause the scanner to malfunction.

Supervisors should review their practices and make compliance with these precautions a part of the job

description for operation of the Kodak i800 Series Scanners or any mechanical device.

ElectroMagnetic Compatibility Statements

European Union

This is a Class A product. In a domestic environment this product may cause radio interference in which

case the user may be required to take adequate measures.

United States

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will be required to

correct the interference at their own expense.

January 2005 2

Taiwan

Japan Class A

This equipment is in the Class A category (Information Technology Equipment to be used in commercial

and/or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference

by Information Technology Equipment aimed at preventing radio interference in commercial and/or

industrial areas.

Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be

caused to radio and TV receivers, etc.

Read the instructions for correct handling.

Peoples Republic of China Class A

A-61169 January 2005 i

Table of Contents

1 Introduction ......................................................................1-1

Product description ............................................................1-2

Standard features ..............................................................1-2

Standard configurations.....................................................1-3

Transport speed.................................................................1-3

Speeds and resolutions .....................................................1-3

Scanner specifications.......................................................1-4

Dimensions ..................................................................1-4

Minimum clearances ....................................................1-4

Acoustic noise..............................................................1-4

Electrical ......................................................................1-4

Power system connection ............................................1-4

Environmental ..............................................................1-4

External components .........................................................1-5

Back of scanner .................................................................1-5

Environmental information and equipment disposal ..........1-6

2 Using the Scanner ...........................................................2-1

Turning on the scanner......................................................2-1

Document preparation .......................................................2-2

Acceptable document materials.........................................2-3

Recommended paper weights ...........................................2-3

Acceptable document sizes ...............................................2-3

Maximum document batch height for automatic feeding ...2-4

Downward and upward curl documents.............................2-4

Adjusting the side guides on the input tray ........................2-4

Adjusting the output tray ....................................................2-5

Scanning documents .........................................................2-6

Loading long documents in the feeder...............................2-7

Continuous and manual feeding ........................................2-7

Feeding thick documents...................................................2-8

ii A-61169 January 2005

3 Operator Control Panel Functions .................................3-1

Enabling and disabling the scanner...................................3-2

Enabling the scanner ...................................................3-2

Disabling the scanner ..................................................3-3

Navigating through the functions on the control

panel menu ..................................................................3-4

Accessing information........................................................3-5

Lowering the elevator tray..................................................3-5

Using the Diagnostics Settings menu ................................3-5

Performing a self-test or extended self-test .................3-6

Running in count-only mode ........................................3-6

Performing a print test..................................................3-7

Performing a patch test................................................3-8

Using the Settings menu....................................................3-9

Changing the alarm volume .........................................3-9

Changing the display contrast....................................3-10

Changing the SCSI ID................................................3-10

Changing the SCSI termination .................................3-11

Setting the elevator tray position................................3-12

Calibrating the scanner....................................................3-13

Jogging the transport .......................................................3-14

Programmable key assignments......................................3-14

4 Document Printer and Patch Reader .............................4-1

The Document Printer........................................................4-1

Printing information ......................................................4-1

Horizontal print position ...............................................4-3

Purging the ink cartridge ..............................................4-4

Replacing the ink cartridge ..........................................4-5

Replacing the ink blotter strips.....................................4-7

Setting the printer position ...........................................4-9

The Patch Reader............................................................4-10

Patch types ................................................................4-10

Patch code placement ...............................................4-11

Setting the Patch Reader position .............................4-12

A-61169 January 2005 iii

5 Maintenance .....................................................................5-1

Cleaning the paper path.....................................................5-1

Cleaning the upper transport area .....................................5-2

Cleaning the vertical transport area ...................................5-5

Cleaning the transport area ...............................................5-6

Cleaning the printer and patch head..................................5-9

Cleaning the imaging guides............................................5-10

Maintenance and replacement procedures......................5-11

Replacing the feed module and feed module tires...........5-12

Replacing the feed module ........................................5-13

Replacing the feed module tires ................................5-13

Separation roller and tires................................................5-15

Replacing the separation roller ..................................5-15

Replacing the separation roller tires ..........................5-16

Changing the separation pad...........................................5-16

Cleaning the feed module tires and separation roller

roller tires ...................................................................5-17

Replacing lamps ..............................................................5-17

Replacing the imaging guides..........................................5-20

Customizing the side guides for self-centering feeding ...5-21

Changing the output tray side guides ..............................5-23

Ordering supplies.............................................................5-25

6 Troubleshooting/Messages ............................................6-1

Clearing the document path...............................................6-1

Message Listing.................................................................6-5

Document sensor location ...............................................6-10

Problem solving chart ......................................................6-11

A-61169 January 2005 1-1

1 Introduction

This User’s Guide provides information and operator procedures for the

Kodak i800 Series Scanners. The information in this guide is for use with

all of the i800 Series Scanners unless otherwise noted.

Chapter 1, Introduction provides general information about the i800

Series Scanners including a product description, features and benefits,

specifications, an overview of external components and user precautions.

Chapter 2, Using the Scanner includes information on how to

prepare your documents for scanning, elevator tray and output tray

adjustments, turning the scanner on and off and how to scan documents.

Chapter 3, Operator Control Panel Functions provides a list of the

icons found on the Operator Control Panel and what functions can be

performed using the Operator Control Panel.

Chapter 4, Document Printer and Patch Reader provides

instructions for using and changing the location of the Document Printer 1

and the Patch Reader. This chapter also instructs how to change and

purge the ink cartridge.

Chapter 5, Maintenance provides complete maintenance procedures

for the i800 Scanner, including replacement procedures for the feeder

module and tires, separation roller and tires, exposure lamps and imaging

guides.

Chapter 6, Troubleshooting/Messages provides a message listing, a

problem solving chart and how to clear a document jam.

1-2 A-61169 January 2005

Product description The Kodak i800 Series Scanners are ideal for operation with bi-tonal

and/or color/grayscale documents, documents with shaded backgrounds

or foregrounds, and mixed document sets. These scanners offer a new,

user interface and Kodak-patented technologies that produce high quality

production images.

Standard features The following features are standard on the Kodak i800 Series Scanners.

• Simultaneous output of color/grayscale and bi-tonal images (i820 and

i840 scanners only)

• SurePath paper handling, featuring:

– 1,000-sheet QuickSet elevator that automatically returns to the

batch level you set

– Automatic feeder with single-sheet feeding and operator-assisted

document stacks. Allows you to set the elevator level to

accommodate 25-, 250- 500-, 750- 1000-document stacks

– 3D Multi-feed Detection, using ultrasonic technology, offering

outstanding reliability

– Flexible document feeding center- and edge-aligned

– An adjustable output tray that handles documents of varying sizes

• The Tri-Color Plus Array provides, in one pass, true color and bi-tonal

images

• Zone Processing allows operator selection of a fixed subsection or

zone (i820 and i840 scanners only)

• PerfectPage, now with iThresholding (color/grayscale and bi-tonal)

• Built-in iThresholding, Adaptive Threshold Processing (ATP), image

compression, despeckle, error diffusion, and dithering for bi-tonal

scanning

• Electronic Color Dropout

• Color on-the-fly

• Accepts custom color tables

• A wide variety of image output resolutions in bi-tonal and

color/grayscale are available

• Easily upgradeable models, at your site, with minimal downtime

• Bundled ISIS and TWAIN drivers

• Friendly operator interface only seven operator control buttons

• Ease-of-use easy replacement of consumables

• Illumination tracking with calibration alert

• Diagnostics and modular design simplify service and minimize

downtime

• Image address with Patch Reader support

• Document Printer 1 imprinting on scanned documents

A-61169 January 2005 1-3

Standard

configurations

Four models of the Kodak i800 Series Scanners are available:

• Kodak i810 Scanner (bi-tonal) provides bi-tonal scanning with

throughput speeds up to 120 ppm

• Kodak i820 Scanner provides color/grayscale and bi-tonal

scanning simultaneously with throughput speeds up to 120 ppm

• Kodak i830 Scanner (bi-tonal) provides bi-tonal scanning with

throughput speeds up to 160 ppm

• Kodak i840 Scanner provides color/grayscale and bi-tonal

scanning simultaneously with throughput speeds up to 160 ppm

Transport speed Following is the minimum and maximum paper transport speed and

capacity of the scanner:

Dimension Minimum Maximum Operational Mode

Length 6.4 cm (2.5 in.) 27.9 cm (11 in.) Auto-feed

Length 27.9 cm (11 in.) 43.2 cm (17 in.) Auto-feed with extensions

Length 43.2 cm (17 in.) 76.1 cm (30 in.) Operator assistance

Width 6.4 cm (2.5 in.) 8.9 cm (3.5 in.) Operator assistance

Width 8.9 cm (3.6 in.) 30.5 cm (12 in.)* Auto-feed

* The scanner transport will allow feeding a 30.5 cm (12-inch)-wide

document but will only scan an area of 29.7 cm (11.7 inches) in width.

Speeds and

resolutions

The chart below provides speeds and resolutions for the i800 Series

Scanners:

Scanner Throughput

(ppm)

Speed (ips) Bi-tonal

Resolution (dpi)

Color/Grayscale

Resolution (dpi)

i810 120

200

300, 240

400

N/A

i820 120

45*

200

300, 240

400

200, 150, 100

200, 150

200

i830 160

106

18.67

200

300, 240

400

N/A

i840 160

106

60*

18.67

200

300, 240

400

200, 150, 100

300*, 200, 150, 100

300, 200

* Throughput at these settings may vary based on system limitations.

1-4 A-61169 January 2005

Scanner specifications Following are the dimensions and clearances for the Kodak i800 Series

Scanners:

Dimensions Height: 124 cm (49 in.)

Width: 66 cm (26 in.)

Depth: 127 cm (50 in.)

Weight: 204 kg (450 lbs) including packaging

188 kg (414 lbs) without packaging

Minimum clearances The table below provides the minimum clearances for normal operation

and maintenance of the i800 Series Scanners:

Front Rear Right Side Left Side Top

Normal

Operation

N/A 4 in.

10 cm

4 in.

10 cm

4 in.

10 cm

10 in.

25 cm

Maintenance 40 in.

102 cm

4 in.

10 cm

24 in.

61 cm

4 in.

10 cm

24 in.

61 cm

Acoustic noise • Operator position standby mode:

– Sound Pressure Level (LA): 39.8 dB(A)

• Operator position full system operating mode:

– Sound Pressure Level (LA): 65.4 dB(A)

– Instantaneous Peak Values >130 dB(C) None

• Sound Power Level (LWA):

– Standby 56.4 dB(A)

– Full System 72.0 dB(A)

NOTE: All data was measured in accordance with DIN 45635, ANSI

S12.10-1985, and ISO 7779 in a hemi-anechoic chamber.

Electrical 100 – 127 V, 6.5 A, 50/60 Hz

200 – 240 V, 3.5 A, 50/60 Hz

Power system

connection

This product is also designed for Norwegian IT power system with phase-

to-phase voltage 230V.

Environmental Temperature: 15 to 35°C (59 to 95°F)

Humidity: 15 to 76% (dry bulb)

Altitude: up to 8000 feet (2438 meters)

Andere Handbücher für I810 - Scanner Firmware - PC

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kodak Scanner Handbücher

Kodak

Kodak ScanMate i940 Bedienungsanleitung

Kodak

Kodak Guidelines 3000 series Betriebsanleitung

Kodak

Kodak Scan Station 700 Bedienungsanleitung

Kodak

Kodak i1400 Series Bedienungsanleitung

Kodak

Kodak i5000 Series Bedienungsanleitung

Kodak

Kodak I780 - Document Scanner Bedienungsanleitung

Kodak

Kodak Scan Station 500 Bedienungsanleitung

Kodak

Kodak Digital Science 7520 Bedienungsanleitung

Kodak

Kodak RFS2035 PLUS FILM SCANNER Bedienungsanleitung

Kodak

Kodak i800 Series Bedienungsanleitung

Kodak

Kodak A-61003 Produktinformationsblatt

Kodak

Kodak i30 Bedienungsanleitung

Kodak

Kodak Ngenuity 9000 Series Bedienungsanleitung

Kodak

Kodak Scan Station 500 Bedienungsanleitung

Kodak

Kodak SV 710 - EASYSHARE Digital Picture Frame Service-Handbuch

Kodak

Kodak HR 500 PLUS Bedienungsanleitung

Kodak

Kodak i100 Series Bedienungsanleitung

Kodak

Kodak Truper 3210 Bedienungsanleitung

Kodak

Kodak Kodak i1840 Bedienungsanleitung

Kodak

Kodak Guidelines 3000 series Montageanleitung

Kodak

Kodak i600 Series Bedienungsanleitung

Kodak

Kodak SCAN STATION 100 Schulungshandbuch

Kodak

Kodak 2400 DV Plus Bedienungsanleitung

Kodak

Kodak s1740 Bedienungsanleitung

Beliebte Scanner Handbücher anderer Marken

Z/I Imaging

Z/I Imaging PhotoScan 2001 Bedienungsanleitung

Renkforce

Renkforce DS100-5M Bedienungsanleitung

Image Access

Image Access WideTEK A2 Bedienungsanleitung

Canon

Canon imageFORMULA CR-120N Bedienungsanleitung

Fujitsu

Fujitsu FI-4860C2 Bedienungsanleitung

GeoSlam

GeoSlam ZEB Horizon Montageanleitung

Revopoint

Revopoint POP Bedienungsanleitung

Fujitsu

Fujitsu fi-4860C Bedienungsanleitung

Eddyfi Technologies

Eddyfi Technologies Floormap X Bedienungsanleitung

Faselase

Faselase F6 Bedienungsanleitung

Fujitsu

Fujitsu CardMinder Bedienungsanleitung

Uniden

Uniden BC340CRS Bedienungsanleitung

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Bedienungsanleitung

Mustek

Mustek PageExpress 4800 Pro Bedienungsanleitung

Optex

Optex 750830 Bedienungsanleitung

Innova

Innova 5210 Bedienungsanleitung

Visioneer

Visioneer CardReader 100 Kurzanleitung

Rohde & Schwarz

Rohde & Schwarz TSME6 Bedienungsanleitung