Kohler EVOK K-18343T Bedienungsanleitung
, 2010
Copyright Kohler China Ltd., 2010
·
·
·
·
Please read these instructions carefully to
familiarize yourself with the required tools, materials,
and installation sequences. Follow the sections that
pertain to your particular installation. This will help
you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
Please provide adequate available space for the
bath unit in accordance with rough-in. Arrange the
location of drain in advance.
All installations must comply with council and local
authority by-laws. It is the responsibility of the installer
to ensure that the waste is made watertight by means
of silicone sealant or caulking compound.
The bath can be installed after the decoration of
the bathroom walls is finished. However, bath drain and
water pipe shall be pre-arranged.
please leave these
instructions for the consumer.
IMPORTANT:
NOTE:
·
·
·
·
BEFORE YOU BEGIN
A.
·
·
A. Summary Of Key Requirements
Observe all local plumbing codes.
Install the unit to a level subfloor.
·
·
PRODUCT REQUIREMENTS
EVOK
INSTALLATION INSTRUCTIONS
FREESTANDING ACRYLIC BATH
K-18343T/K-18347T/K-18353T
368 201419
B. Plumbing Specifications
If using a rim-mounted bath faucet, flexible connections
between the valves and spout may be required.
Confirm adequate mounting, connection of
specified faucet for your installation.
space
B.
C. Product Inspection
Uncrate and inspect bath for damage. All Kohler s
baths have been manufactured with sophisticated
craftsmanship. However, please inspect for any
possible damage that may have occurred in transit.
Leave all materials in the crate during construction to
prevent damage.
'
C.
-1-
1119528-T01-C
-2-
NOTE: Damage occurred during transport or
installation shall not be covered by warranty.
SITE REQUIREMENTS
A.
A. Preparation
Check the flooring under the bath, and make repairs as
needed. Make sure the is level. It is strongly
recommended to prepare waterproof layer for the
subfloor beforehand.
Subfloor
subfloor
D.
D. Clearance Requirements
Check the roughing-in and room dimensions to provide
adequate available space for the bath unit.
·
·
·
·
·
·
·
·
·
·
Adjustable pipe
wrench
Rule
Level
Safety shoes
Safety glasses
Square
Screwdriver
Pliers
Utility knife
Adjustable wrench
·
·
·
·
·
·
·
Plumbers putty
Wall coverings(as necessary)
Silicone sealant
Gypsum cement(optional)
Construction adhesive
(optional)
Protective covering for
bathtub
Nails
B. Materials RequiredA. Tools Required
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
()
()
()
B.
A.
INSTALLATION REQUIREMENTS
D. New or Replacement Installation
Requirements
This bath can be installed in new or existing bathrooms.
For replacement: Remove the old bath, and remove
enough old wall material and floor covering from the
area to allow for installation. Remove any old plumbing
that does not confo m to the rough-in requirements.
For new installation: Position the plumbing according to
the rough-in dimensions. Cap the suppliers, and check
for leaks.
r
D.
C. Installation Note: C. :
Read the entire installation instructions included with
fixture before beginning the installation.
If installing a rim-mounted faucet, make sure there is no
interference with drain overflow before drilling any
holes.
1119528-T01-C
-3-
INSTALL THE BATH
A. Put the bath at desired position
1. Adjust the feet under the bath to make it level. Adjust
the height of the bath to the height marked in the
Roughing-In. Tighten the nut on the adjustable feet
to settle the height of the bath.
The bath must be installed level on a flat and level
subfloor without any bumps or protrusions.
Adjust the height of the bath to the height marked in
the Roughing-In.
IMPORTANT:
!
!
A.
1.
!
!
2. Place the base on the floor. 2.
3. Fix the base on the floor with silicone sealant. 3.
4. Apply silicone sealant around the tail end of the
drain hose. Connect the drain hose with floor drain.
Make sure the drain hose protrudes from the floor for
a certain length to facilitate future bath removal.
4.
BEFORE INSTALLATION
A.A. Protect the Bath Unit
Cover the bath with a protective layer or similar
material. Be careful not to scratch the bath surface.
5. Connect cold and hot supplies and check all
connections for leak.
5.
1119528-T01-C
6. Apply lubricating oil both to the inner surface of the
guide bush and the outer surface of the guide pin.
Insert the guide pin into the guide bush to finally fix the
bath onto the floor.
6.
-4-
B. Plumbing Installation
The drain has been installed onto the bath before it
leaves factory. Fill the bath with water before the bath
is securely positioned so as to check the connections
for leaks. Damage caused by negligence is not covered
by warranty.
Be careful not to damage the bottom of the bath
and the subfloor.
Note:
B.
Guide Pin
Guide Bush
Base
1119528-T01-C
C. install theRemove and freestanding
bath
If the freestanding bath needs removing, please follow
the steps below:
Lift the bath levelly, then the guide pin could be
pluged out of the guide bush. Then remove the nut
on the drain tail pipe.
1)
C.
1)
-5-
*
*2
Mequiars 28 ( )
()
Cleaning and Care
Cleaning Acrylic Surfaces: Do not use abrasive
cleansers on any acrylic surfaces, as they will scratch
and dull the surface. Wipe out the bath after each use
to prevent a build-up of soap and scum.
If the acrylic surface becomes dull, an automotive type
rubbing compound may be used on the unit, followed
by an application of paste wax.
We recommend:
Rubbing compound mequiars mirror glaze 28 metal
polish (import product)
reen oil.
*
*
G
IMPORTANT CONSUMER INFORMATION
2) When installing the freestanding bath, please first
apply lubricating oil both to the inner surface of the
guide bush and the outer surface of the guide pin,
and then insert the guide into the guide bush.
2)
Nut of the Drain Tail Pipe
1119528-T01-C
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Kohler Badewanne Handbücher
Kohler
Kohler Hourglass 30 K-1201 Bedienungsanleitung
Kohler
Kohler PRELUDE K-8266T Bedienungsanleitung
Kohler
Kohler K-1487-H2 Montageanleitung
Kohler
Kohler K-1160P-LA Kurzanleitung
Kohler
Kohler K-1257 Kurzanleitung
Kohler
Kohler K-1492 Kurzanleitung
Kohler
Kohler Iron Works Tellieur K-727 Montageanleitung
Kohler
Kohler K-870 Montageanleitung
Kohler
Kohler K-1397-H2 Montageanleitung
Kohler
Kohler K-1239 Kurzanleitung
Kohler
Kohler Underscore Oval K-5714-XH2G Bedienungsanleitung
Kohler
Kohler K-1457 Montageanleitung
Kohler
Kohler Memoirs K-8333-0 Bedienungsanleitung
Kohler
Kohler K-1189 Bedienungsanleitung
Kohler
Kohler K-1106 Bedienungsanleitung
Kohler
Kohler K-1229 Kurzanleitung
Kohler
Kohler K-12515 Betriebsanleitung
Kohler
Kohler K-1106 Bedienungsanleitung
Kohler
Kohler Memoirs K-723 Kurzanleitung
Kohler
Kohler K-1166 Bedienungsanleitung
Beliebte Badewanne Handbücher anderer Marken
Woodbridge
Woodbridge BJ500 Montageanleitung
Whirlpool
Whirlpool Ariel ARL-702 Bedienungsanleitung
TEIKO
TEIKO EXCELLENT DUO Bedienungsanleitung
American Standard
American Standard Colony 5-1/2' x 32" Bedienungsanleitung
American Standard
American Standard 3052OD.X0X Kurzanleitung
agape
agape MARSIGLIA AVAS1075 Bedienungsanleitung
