Kohler PRELUDE K-8266T Bedienungsanleitung

ã, 2004

116867-T01-B

B. Installer Hazard Notification

CAUTION!!

NOTICE:

Risk of personal injury.

Cast iron baths are extremely heavy. Wear appropriate

safety equipment when installing these products.

Observe all local plumbing codes.

A. Introduction

Please read these instructions carefully to

familiarize yourself with the required tools, materials,

and installation sequences. Follow the sections that

pertain to your particular installation. This will help

you avoid costly mistakes. In addition to proper

installation, read all operating and safety instructions.

All information is based on the latest product

information available at the time of publication.

Kohler China Ltd. reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning,

and warranty information-please leave these

instructions for the consumer.

PRODUCT REQUIREMENTSPRODUCT REQUIREMENTS

A. Summary Of Key Requirements

Observe all local plumbing codes.

Install the unit to a level subfloor.

Provide properly-dimensioned framing.

Baths are designed for a variety of installations,

depending upon the model chosen.

B. Product Inspection

Uncrate and inspect bath for damage. Leave all

materials in the crate during construction to prevent

damage.

ENAMELED CAST IRON BATH

INSTALLATION INSTRUCTIONS

PRELUDE

BEFORE YOU BEGINBEFORE YOU BEGIN

368 201419

QUIETUDE

K-8266T/K-8267T/K-8268T/K-8269T

K-8270T/K-8271T/K-8273T/K-8275T

K-8262T/K-8263T

1500MM ........................1462 662mm

1600MM ........................1562 662mm

1700MM ........................1662 662mm

1400MM ........................1362 662mm

D. CUT-OUT Dimensions

PRELUDE 1500MM......................1462 662mm

1600MM......................1562 662mm

1700MM......................1662 662mm

QUIETUDE 1400MM......................1362 662mm

ROUGHING-IN

A. Roughing-in Note

Fixture dimensions are nominal and conform to

tolerances in ASME/ANSI Standard A112.19.1M.

/ A112.19.1M

B. Determine Roughing-in

Measure the height, width, and depth of the bath. Verify

these dimensions with those on this page.

Allow clearance at the drain hole location in the flooring.

* 110-118mm

C. Accessory Information

Grip Rail ...................................................K-8645-CP

.........................................................K-8645-CP

INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS

B. Materials Required

Plumbers putty

Wall coverings, as

necessary

Silicone sealant

Protective covering for

bathtub or card board

Metal shims

A. Tools Required

Adjustable pipe

wrench

Rule

Level

Safety shoes

Safety glasses

Square

Pliers

()

700

350

* The with of bath front rim is 110-118mm, Please

select the faucet with matching spout for the bath.

UNIT: mm

89Kg

92Kg

LBA

1500

1400

294 117

69246

86Kg

1600 294 117

93Kg

1700 294 117

K-8266T/7/8/9

K-8270T/1

K-8273T/5

K-8262T/3

435

443

116867-T01-B

C. Clearance Requirements

Check the rough-in atnd room dimensions to provide

adequate available space for the bath unit.

A. Old Bath Removal (if necessary)

Disconnect the drain at the trap. Remove the old wall

material. Slip boards under the old bath feet to protect

the floor, and slide the old bath out of the recess as

illustrated.

SITE REQUIREMENTSSITE REQUIREMENTS

B. Subfloor Preparation

Check the flooring under the bath, and make repairs as

needed. Make sure the subfloor is level.

C. Plumbing Preparation

Position the plumbing according to rough-in dimensions.

Cap the supplies and check for leaks.

BEFORE INSTALLING UNITBEFORE INSTALLING UNIT

12 3

A. The following installation practices

to avoid any potential

damage to the enamel finish.

must be followed

WARNING: Failure to follow the manufacturer's

recommended installation method may result in

damage to the enamel surface.

Do not use sharp objects or metal tools when

handling the bath, especially around the rim area.

Use a clear protective plastic film over tub rim as

well as the bottom of tub to safeguard from dirt and

silicone during the installation process.

For correct installation, bath rim should not come in

direct contact with the walls and/or horizontal

surfaces to avoid transmission of noise and vibration

as well as potential cracks in the enamel finish.

The necessary gap between bath rim and the wall is

2 mm horizontally and 4 mm vertically. Refer to

figures 1, 2, and 3 below.

Before placing setting-in the bath, apply a sanitary

quality silicone filler on all surfaces to come in

contact with the bath rim.

Set the bath in its correct position.

Old Bath

Floor Protection Board

116867-T01-B

B. Partially Install Bath Drain

Install the drain on the bath according to the drain

manufactuer's instructions.

UNIT: mm

INSTALL THE BATHINSTALL THE BATH

tiling

bath

silicone filler

wall

silicone filler

bath

wall

tiling

bath

silicone filler

wall

A2. Through the Floor Drain Bath

Installation

1 . Slide the new bath into position to verify the drain

location and the stud fit. Cut a minimum 152 305

mm hole in the floor for the drain connection.

)

A2.

152

305mm

)

A1. Installation of Bath with Adjustable

Hlight

Slide the new bath into position.

Insert the drain tailpiece into the trap.

Level the bath by positioning metal shims and bricks

under the bath feet and ensure there is enough spate

for the drain. Attention: the metal shims are necessary

to aroid cracking of bricks. Check for level along the top

of the side of the bath and across the drain end. The

bath may have to be moved in and out of the recess

area until it is shimmed properly, if the support feet are

not accessible from the back or side.

A1.

:Metal shim

Level

Brick

116867-T01-B

Use 25~30 Kg dry cement and sand mix. Add water to

make a paste mortar. Remove the tub. Cover the

installation area with the mortar starting from the middle

of the tub as shown. The height of the mortar should

reach the bottom of the tub.

DO NOT CLOG THE DRAIN HOLE.

Place the tub onto the mortar. Insert the drain tailpiece

into the trap.

Make sure that the bottom of the tub is pressed into

mortar in order to secure the tub. Insert two wood

wedges under the tub to support the weight of the tub

until the mortar hardens. (Wedges will remain in the

mortar.) Frequently check the level of the tub.

25~30

NOTE:

B. Install Plumbing

CAUTION: Risk of damage to bath bottom and subfloor.

Ensure a watertight seal on the bath drain connections.

. For through the floor drain installation, when the

bath is securely positioned, connect the drain to the

trap. See fig. A.

2). Install the faucet valving and spout tee. Open the

hot and cold water valves, and check the supply

connections for leaks.

. Run water into the bath, and check the drain

connections for leaks. A

1).

2).

3).

Level

Paste Mortar

Wood Wedge

Middle of Bath

Drain Hole

116867-T01-B

2mm

C. Finish Bath Area Construction

NOTE: An access panel is essential for future

maintenance.

Possible framing arrangements are illustrated below.

Use the framing construction appropriate for your

particular bath model. Some modifications may be

needed for other types of construction, if preferred.

If an apron wall without a ledge is desired, the finished

apron wall surface must be 2 mm under the bath rim.

1). Corner Installation

The suggested framing construction is illustrated.

1).

2). Recess Installation

The suggested framing construction is illustrated.

2).

Recommended For Drop-in Models

3). Peninsular Installation

The suggested framing construction is illustrated.

3).

Finished Wall

Wall

Framing

Construction

Service Access

Finished Wall

Wall

Framing

Construction

Service Access

Finished Wall

Wall

Framing

Construction

Service Access

116867-T01-B

INSTALL THE GRIP RAILINSTALL THE GRIP RAIL

For baths with K-8645-CP.

Place the gasket (6) onto the grip rail(7). Make sure the

gasket is matching the contour of the grip rail. Position

the grip rail with gasket so that the hole lines up with

the hole on the nut pre-installed on the side of bath tub.

Note: the smaller side of the grip rail is on the drain

side of the tub.

Thread the screw (8) into the hole of the grip rail.

Tighten the screw snugly to secure the grip rail. Snap

the cap (9) into each hole.

Repeat above procedures for the other grip rail.

K-8645-CP

(6) (7)

(8)

(9)

COMPLETE FINISH WALLCOMPLETE FINISH WALL

CAUTION: Risk of product damage. Do not support

the weight of the bath by the rim.

Install the ceramic or marble tiles. Seal the joints

between the bath rim and the finished tiled wall using

silicone sealant. RTV (Room Temperature Vulcanizing)

sealant is recommended.

Apply a bead of silicone sealant over the seam

between the bath apron and the finish floor.

()

898

Finished Tiled Wall

Paste Mortar

Brick or Concrete Wall

Framing Construction

Bath

Silicone Filler

116867-T01-B

When cleaning up after installation, do not use abrasive

cleansers as they may scratch and dull the surface.

Use warm water and liquid, non-abrasive detergent to

clean the surface.

Stubborn stains, paint, or tar can be removed with

turpentine or paint thinner. Do not allow cleaners

containing petroleum distillates to remain in contact

with the bath surface for long periods of time. Plaster

can be removed by scraping with wood edge. Do not

use metal scrapers, wire brushes, or other metal tools.

One of the powder type detergents may be used on a

damp cloth to provide mild abrasive action to the

residual plaster.

CLEAN-UP AFTER INSTALLATIONCLEAN-UP AFTER INSTALLATION

IMPORTANT CONSUMER INFORMATION

Safeguard ASME/ANSI

A112.19.1M

pH38 (

)

Housekeeping Responsibilities

The Safeguard slip resistant surface on this bathtub

meets or exceeds the requirements of ASME/ANSI

slip resistance.

Improper maintenance or cleansers may

permanently remove the slip resistant

surface on Kohler bathtubs.

All housekeeping and maintenance

employees must be trained in the proper

cleaning of Kohler bathtubs. Post a copy of

this notice in a readily-visible location.

use steel wool, wire brushes, metal scrapers

or abrasive sponge pads to clean a Kohler

bath tub.

use buffing machines on the slip resistant

surface.

use high alkaline or strong acid cleansers.

use abrasive cleansers.

Use only non-abrasive cleansers and a soft nylon

brush to clean the slip resistant surface.

When using commercial cleansers, use cleansers

with a pH of between three and eight.

Follow cleanser manufacturer instructions very

carefully.

for

A112.19.1M

DANGER!!

NOTICE:

DO NOT

116867-T01-B

LIMITED ONE-YEAR WARRANTYLIMITED ONE-YEAR WARRANTY

(

)

()

138

200021

Plumbing Fixtures and Fittings Limited

One-year Warranty

Kohler plumbing fixtures and fittings are warranted to

be free of manufacturing defects.

This product is warranted for one year from date of

purchase. Kohler China will be responsible for any

problems caused by manufacturing defects provided

with the invoice. Kohler China will, at its election, repair,

replace or make appropriate adjustment where Kohler

China inspection discloses any such defects occurring

in normal usage within one year after purchase.

Implied warranties including that of merchantability and

fitness for a particular purpose are expressly limited in

duration to the duration of this warranty, Kohler China

disclaims any liability for special, incidental or

consequential damages. Damages to the product

caused by misuse, abuse and installation that is not in

accordance with the owner's manual are not covered

by this warranty.

To obtain quick warranty service, please contact your

dealer, or write to Kohler China. (Original sales receipt

must be provided as the proof of purchase.)

Kohler China Investment Company Ltd.

Central Customer Service Center

19/F, Shanghai Square, 138 Huai Hai

Road, Luwan District, Shanghai, PRC

Zip Code: 200021

This is our exclusive written warranty.

116867-T01-B

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Badewanne Handbücher

Kohler

Kohler K-1246 Kurzanleitung

Kohler

Kohler Englefield Valencia 1500 FS Bedienungsanleitung

Kohler

Kohler K-1394-H2 Montageanleitung

Kohler

Kohler K-1257 Kurzanleitung

Kohler

Kohler K-2593-VBW-0 Bedienungsanleitung

Kohler

Kohler K-1195-LA Kurzanleitung

Kohler

Kohler K-1969 Montageanleitung

Kohler

Kohler K-1107 Bedienungsanleitung

Kohler

Kohler K-721 Kurzanleitung

Kohler

Kohler Archer K-2595-G2M Bedienungsanleitung

Kohler

Kohler Windward K-1115-LA Kurzanleitung

Kohler

Kohler K-11195X Bedienungsanleitung

Kohler

Kohler K-1158 Kurzanleitung

Kohler

Kohler Mariposa K-1257-LA-96 Montageanleitung

Kohler

Kohler K-856-M Montageanleitung

Kohler

Kohler Windward K-1112-G Kurzanleitung

Kohler

Kohler K-1106 Bedienungsanleitung

Kohler

Kohler K-1106 Bedienungsanleitung

Kohler

Kohler BATH WALL Kurzanleitung

Kohler

Kohler K-1160-CD Kurzanleitung

Kohler

Kohler K-856-M Montageanleitung

Kohler

Kohler Memoirs K-724-G0 Bedienungsanleitung

Kohler

Kohler Lakewood K-1649 Montageanleitung

Kohler

Kohler K-12345M Montageanleitung

Beliebte Badewanne Handbücher anderer Marken

Agua

Agua BARTOLI-66 Bedienungsanleitung

PAA

PAA PRELUDE Bedienungsanleitung

BETTE

BETTE SILHOUETTE Bedienungsanleitung

American Standard

American Standard Whirlpool/Bathing Pool 2748.XXXW Bedienungsanleitung

Oliveri

Oliveri Naples Bedienungsanleitung

Lyons

Lyons Elite ETLxx663219 Series Bedienungsanleitung

Woodbridge

Woodbridge BJ500 Montageanleitung

Whirlpool

Whirlpool Ariel ARL-702 Bedienungsanleitung

TEIKO

TEIKO EXCELLENT DUO Bedienungsanleitung

American Standard

American Standard 3052OD.X0X Kurzanleitung

agape

agape MARSIGLIA AVAS1075 Bedienungsanleitung

Kallista

Kallista P50045-G5 Montageanleitung

Ariel

Ariel AM Series Bedienungsanleitung

Agua

Agua BAHLI-60 Bedienungsanleitung

DURAVIT

DURAVIT XViu 700443 Bedienungsanleitung

American Standard

American Standard Colony 2740 Series Bedienungsanleitung

Rapsel

Rapsel OFURO Handbuch

GALA

GALA Emma Bedienungsanleitung