Kohler 1190330-NA Bedienungsanleitung

11095640-W2-B

IMPORTANT

INSTALLER: THIS MANUAL IS THE PROPERTY OF THE

CUSTOMER AND MUST BE RETAINED WITH THE PRODUCT

FOR MAINTENANCE AND OPERATIONAL PURPOSES.

Installation and User Guide

Built-In Shower Valve

MODEL NUMBERS

Important! Please quote the above model number(s) when ordering spares

1190330-NA, 998W-K-NA

Temperature Only

Single Sequential

1095640-W2-B

CONTENTS

Safety Warnings ...................................................................................... 3

Pack Contents .........................................................................................5

Specications ..........................................................................................6

Pressures and Flow Rates ...................................................................6

Dimensions ..............................................................................................7

Installation ...............................................................................................8

Suitable Plumbing Systems..................................................................8

General................................................................................................. 8

Reversing the Outlet Position.............................................................10

Installation Procedure........................................................................... 11

Operation ...............................................................................................15

Commissioning .....................................................................................16

Maximum Temperature Setting ..........................................................16

Fault Diagnosis......................................................................................18

Maintenance...........................................................................................19

Spare Parts ............................................................................................21

Notes ......................................................................................................22

Customer Care.......................................................................................24

31095640-W2-B

WARNING - This product can deliver scalding temperatures if not installed,

operated or maintained in accordance with the instructions, warnings and

cautions contained in this guide.

The function of a thermostatic mixing valve is to deliver water consistently at a safe

temperature. In keeping with every other mechanism, it cannot be considered as

functionally infallible and as such, cannot totally replace a supervisors vigilance

where that is necessary. Provided it is installed, commissioned and maintained within

manufacturers recommendations, the risk of failure, if not eliminated, is reduced to

the minimum achievable.

Kohler thermostatic mixers are precision engineered and should give continued safe

and controlled performance, provided:

1. They are installed, commissioned, operated and maintained in accordance with

the manufacturer’s recommendations.

2. Periodic attention is given, when necessary, to maintain the product in good

functional order.

Caution!

1. DO NOT install the product in a position in which service access is restricted.

2. Read all of these instructions. Retain this guide for later use.

3. Installation must be carried out in accordance with these instructions, and must

be conducted by designated, qualied and competent personnel.

4. Pass on this guide in the event of change of ownership of the installation site.

5. Follow all warnings, cautions and instructions contained in this guide.

6. Make sure that you fully understand how to operate this shower before use, read

all operating instructions and retain this guide for future reference.

7. This product is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction concerning the use of

the product by a person responsible for their safety.

8. Anyone who may have difculty understanding or operating the controls of any

shower should be attended whilst showering. Particular consideration should be

given to the young, the elderly, the inrm or anyone inexperienced in the correct

operation of the controls.

9. Children should be supervised to ensure that they do not play with the product.

10. DO NOT perform any unspecied modications to the shower or its accessories.

When servicing only use genuine Kohler replacement parts.

11. Only Kohler recommended outlet ttings should be used.

12. DO NOT operate the temperature control rapidly, allow 10 – 15 seconds for the

temperature to stabilise before use.

SAFETY WARNINGS

1095640-W2-B

13. Care is required when adjusting ow or temperature, make sure that the

temperature has stabilised.

14. Care is required if the product is turned off and back on during showering as this

may result in unstable temperature. Ensure temperature has stabilised before

re-using product.

15. Sunburn or skin conditions can increase your sensitivity to hot water. Make sure

that you set the shower to a cooler temperature.

16. DO NOT t the product where it may be exposed to freezing conditions. DO

NOT operate if the appliance is frozen, allow the appliance to thaw and check

for leaks before using.

17. Insulate any pipework that could be exposed to freezing conditions.

18. The water supplies to this product must be isolated if the product is not to be

used for a long period of time. If the product or pipework is at risk of freezing

during this period they should also be drained of water.

19. When this product has reached the end of its serviceable life, it should be

disposed of in a safe manner, in accordance with current local authority recycling,

or waste disposal policy.

20. If you experience any difculty with the installation of your new shower, then

please refer to “Fault Diagnosis”, before contacting Kohler Mira Limited. Our

telephone and fax numbers can be found on the back cover of this guide.

51095640-W2-B

PACK CONTENTS

q1 x Mixer Valve

Single Sequential Temperature Only

q1 x Building in Shroud

q1 x Adapter Pack

q3 x Screws q3 x Wall Plugs

1095640-W2-B

SPECIFICATIONS

Pressures and Flow Rates

Note! For optimum performance, dynamic supply pressures should be nominally

equal.

Recommended Minimum Dynamic Supply Pressure: 0.15 bar.

Recommended Maximum Dynamic Supply Pressure: 5 bar.

Maximum Static Pressure: 10 bar.

Recommended Minimum Flow Rate: 3 L/min at mid-blend with equal dynamic

supply pressures.

Recommended Maximum Flow Rate: 35 L/min at mid-blend (which equates to

maximum pressure loss of 1.8 bar).

Temperatures

Optimum performance is obtained when temperature differentials of 20°C or more

exist between blend and either supply. Blend control accuracy will begin to diminish

at temperature differentials below 12°C.

Blend Temperature Range: between ambient cold and approximately 60°C,

according to hot water supply temperature.

Thermostatic Control Range: approximately 25-60°C.

Optimum Thermostatic Control Range: 30-50°C.

Recommended Minimum Cold Water Temperature: 1°C.

Recommended Maximum Hot Water Supply Temperature: 85°C.

Connections

Inlets and Outlet: 1/2” BSP external union or 15 mm compression.

Pressure Loss (bar)

Flow Rate (L/Min)

0.51.0 1.

.00

71095640-W2-B

DIMENSIONS

All dimensions are nominal and in mm.

140

Single Sequential Temperature Only

1095640-W2-B

INSTALLATION

Suitable Plumbing Systems

Gravity Fed:

The thermostatic mixer must be fed from a cold water cistern (usually tted in the

loft space) and a hot water cylinder (usually tted in the airing cupboard) providing

nominally equal pressures.

Gas Heated System:

The thermostatic mixer can be installed with a combination boiler.

Unvented Mains Pressure System:

The thermostatic mixer can be installed with an unvented, stored hot water system.

Mains Pressurised Instantaneous Hot Water System:

The thermostatic mixer can be installed with systems of this type with balanced

pressures.

Pumped System:

The thermostatic mixer can be installed with an inlet pump (twin impeller). The pump

must be installed on the oor next to the hot water cylinder.

General

Installation must be carried out in accordance with these instructions, and must be

conducted by designated, qualied and competent personnel.

The installation must comply with the “Water Supply Regulations 1999 (Water

Fittings)” or any particular regulations and practices, specied by the local water

company or water undertakers.

Note! Make sure that all site requirements correspond to the information given in

section: ‘Specications’.

1. The product must not be installed in an area where it may freeze. Pipework to

the product that could become frozen must be properly insulated.

2. Do not install the product in a position in which service access is restricted.

3. For stud partitions alternative xings may be required.

4. Isolating valves must be installed close to the product for ease of maintenance.

5. Pipework must be rigidly supported and avoid any strain on the connections.

6. Pipework dead-legs should be kept to a minimum.

7. If pipework enters the product from the rear through a hole in the wall, provision

must be made to prevent water ingress back into the wall structure.

91095640-W2-B

(0.1 bar). Double checkvalves tted in the inlet supply to the appliance cause a

pressure build up, which affect the maximum static inlet pressure for the appliance

and must not be tted. For Fluid category 5 double checkvalves are not suitable.

9. The showerhead should be positioned so that it discharges down the centre line

of the bath or across the opening of a shower cubicle.

10. Only use the inlet connections supplied with the product. DO NOT use any other

type of ttings.

11. All pipework must be checked for leaks before the product installation is

completed. The product should be pressurised and the inlet & outlet connections

inspected.

12. DO NOT overtighten connections, screws or grubscrews as product damage

may occur.

13. Upon completion of installation, or if the product is dismantled during installation

or servicing, then the product must be inspected to ensure that there are no leaks.

14. Having completed the installation, make sure that the user is familiar with the

operation of the product.

Zone of

Backow Risk

30 mm

Minimum

Toilet or Bidet

FC5

Hand Basin

FC3

Bath or Shower

Tray FC3

Mixer

Shower

25 mm

Minimum

25 mm Minimum

8. The position of the shower and

shower ttings must provide a

minimum gap of 25 mm between

the showerhead and the spill

over level of any bath, shower

tray or basin and a minimum

gap of 30 mm between the

showerhead and the spill over

level of any toilet, bidet or other

appliance with a Fluid Category

5 backow risk (see diagram).

Note! There will be occasions when

the hose retaining ring will not provide

a suitable solution for Fluid Category

3 installations, in these instances an

outlet double checkvalve must be

tted, this will increase the required

supply pressure typically by 10kPa

1095640-W2-B

Reversing the Outlet Position

1. Remove the outlet adapter using a 12 mm hexagonal wrench (not supplied).

2. Remove the outlet blanking plug using a 12 mm hexagonal wrench.

3. Screw the outlet adapter, complete with ‘O’ seal into the bottom hole previously

blanked and tighten.

4. Screw the outlet blanking plug, complete with ‘O’ seal, into the top hole and

tighten.

Outlet Blanking

Plug

Outlet Adapter

Temperature Only valve shown

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Steuereinheit Handbücher

Kohler

Kohler K-528-K1 Montageanleitung

Kohler

Kohler K301 Bedienungsanleitung

Kohler

Kohler K-687 Montageanleitung

Kohler

Kohler K-682 Bedienungsanleitung

Kohler

Kohler K-308 Bedienungsanleitung

Kohler

Kohler K-402 Bedienungsanleitung

Kohler

Kohler 28139T-DR Bedienungsanleitung

Kohler

Kohler 28138T Bedienungsanleitung

Kohler

Kohler DTV+ Montageanleitung

Kohler

Kohler K-10675 Betriebsanleitung

Kohler

Kohler K-305 Montageanleitung

Kohler

Kohler GM77177-KP1-QS Bedienungsanleitung

Kohler

Kohler Mastershower K-406 Bedienungsanleitung

Kohler

Kohler 880A Bedienungsanleitung

Kohler

Kohler DTV+ Konnect K-97999-NA Bedienungsanleitung

Kohler

Kohler K-10970 Montageanleitung

Kohler

Kohler ENGLEFIELD K-98095X Montageanleitung

Kohler

Kohler K-402 Montageanleitung

Kohler

Kohler Rite-Temp K-8300-PX Bedienungsanleitung

Kohler

Kohler K-682 Bedienungsanleitung

Kohler

Kohler K-10675 Bedienungsanleitung

Kohler

Kohler K-11842 Series Montageanleitung

Kohler

Kohler K-306 Bedienungsanleitung

Kohler

Kohler K-T10669 Montageanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung