Kohler K-682 Bedienungsanleitung
Installation Guide
Six-Port Thermostatic Valve
Mproduct numbers are for Mexico (i.e. K-12345M)
Los números de productos seguidos de Mcorresponden a México
(Ej. K-12345M)
Français, page “Français-1”
Español, página “Español-1”
K-682
1043183-2-B
IMPORTANT INSTRUCTIONS
WARNING: When using electrical products, basic precautions should always be followed, including
the following:
DANGER: Risk of electric shock. Connect only to circuits protected by a Ground-Fault
Circuit-Interrupter (GFCI) or Earth-Leakage Circuit Breaker (ELCB). Grounding is required. The unit
should be installed and grounded by a qualified service representative.
WARNING: Risk of electric shock. A licensed electrician should route all electrical wiring.
WARNING: Risk of electric shock. Disconnect power before servicing.
WARNING: Unauthorized modification may cause poor performance of the valve. Do not make
modifications to the valve as this could adversely affect the performance of the valve and void the
warranty. Kohler Co. shall not be liable under its warranty or otherwise for personal injury or damage
caused by any such unauthorized modification.
WARNING: Risk of injury or property damage. Please read all instructions thoroughly before
beginning installation.
NOTICE: Follow all plumbing, electrical, and building codes.
NOTICE: Provide generous, unrestricted service access to the valve. Provide access for servicing the
valve and interface. This access must be located immediately next to the valve. Refer to the roughing in
information.
Specifications
Pressures
Maximum Static Pressure 125 psi, 862 kPa, 8.6 bar
Supply Pressure Differential* Max 5 psi, 34.5 kPa, 0.34 bar (Equal pressures recommended.)
Minimum Flow Rate 1.6 gpm (Less than 72 psi dynamic pressure.)
6 lpm (Less than 500 kPa maintaining pressure.)
2.1 gpm (Greater than 72 psi dynamic pressure.)
8 lpm (Greater than 500 kPa maintaining pressure.)
Temperatures
Programmable Temperature Max 120°F (49°C) Min 79°F (26°C) Full cold may also be selected.
Default Temperature at Start-up 102°F (39°C)
Minimum Mixed Temperature
Differential from Hot Supply 3.6°F (2°C)
Optimum Thermostatic Control Range 86°F (30°C) to 120°F (49°C)
Temperature Stability at Recommended
Supply Conditions +/- 1.6°F (1°C)
Ambient Temperature Greater than 34°F (1°C), Max 104°F (40°C)
Maximum Relative Humidity 95% non-condensing
Electrical
Electrical Service 100-240 VAC, 50-60 Hz, 1.5 A
User Interface Cable Length (supplied) 30 ft (9.14 m)
* In commercial applications where there is a large difference in hot and cold supply pressures or frequent
fluctuation in either supply line is anticipated, it is strongly recommended that pressure regulators be
installed.
1043183-2-B 2 Kohler Co.
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few minutes to review this manual before
you start installation. If you encounter any installation or performance problems, please don’t hesitate to
contact us. Our phone numbers and website are listed on the back cover. Thanks again for choosing Kohler
Company.
Tools and Materials
Sealant
Tape
Screwdrivers
Level
Pencil
DrillAdjustable
Wrench
Plus:
• (2) 3/4" and (6) 1/2" Union Connectors
• Wood and Framing Materials
• PEX Tubing or Copper Tubing
• (2) Water Hammer Arrestors (Recommended)
• (2) Supply Shut-Off Valves
Hacksaw or Tube Cutter
Propane
Torch
Solder
Pipe Wrench Wood Saw Hammer
Kohler Co. 3 1043183-2-B
Roughing-In
Before You Begin
CAUTION: Risk of product damage. The power supply and valve are rated to operate in temperatures
up to 104°F (40°C). Do not install the power supply or valve under a whirlpool surround or any
location where the temperature may reach temperatures over 104°F (40°C).
CAUTION: Risk of product damage. This valve contains plastic and rubber components; do not apply
excessive heat near the valve or apply flux or acids directly onto the valve.
CAUTION: Risk of product damage. Do not apply petroleum-based lubricants to the valve
components.
CAUTION: Risk of product damage. Inlet and outlet threaded connections should be made using
sealant tape or liquid sealant. Do not use oil-based, non-setting compounds, such as plumbers putty, on
the threaded connections.
CAUTION: Risk of solenoid failure. No outlet should not flow more than 10 gal/min.
Observe all local plumbing, building, and electrical codes.
Provide access for servicing.
Read these instructions and determine all required components along with their installation
locations before beginning this installation.
For optimum performance, 3/4″dedicated water supply lines are recommended.
A minimum 2″(5.1 cm) drain or a drain system capable of handling a water flow of 20 gpm (76
lpm) is recommended for this installation.
20-1/8" (51.1 cm)
21-5/16" (54.1 cm)
5-15/16" (15 cm)
13' 1/8" (396.6 cm)30-7/8" (78.4 cm)
22-1/4" (56.5 cm)
1/2" NPT Outlets (6)
3/4" NPT Inlets
Cold
Hot
7-3/8"
(18.7 cm)
9-3/16"
(23.3 cm)
3"
(7.6 cm)
2-1/8"
(5.4 cm)
3-5/16"
(8.4 cm)
1-3/4" (4.4 cm)
1-3/4" (4.4 cm)
1-3/4" (4.4 cm)
1-3/4" (4.4 cm)
1-3/4" (4.4 cm)
3-1/16" (7.8 cm)
2-3/16" (5.6 cm)
3-3/16"
(8 cm)
2"
(5.1 cm)
1-5/16" (3.3 cm)
1043183-2-B 4 Kohler Co.
Before You Begin (cont.)
If possible, flush all piping thoroughly before installing the valves to prevent clogging the inlet
filters.
A licensed electrician should install a 120 V GFCI electrical outlet, within the stud framing, in close
proximity to the valve.
If possible, install the electrical outlet prior to installing the valve.
A dedicated water heater, 80 gallon (302.8 L) or larger, is recommended for this installation.
This valve complies with UL1951, ASME A112.18.1, ASSE 1016, CSA B125, and CSA C222 No.
218.2-93. This valve is listed with ASSE, CSA, IAPMO/UPC, and UL.
Kohler Co. reserves the right to make revisions in the design of faucets without notice, as specified
in the Price Book.
Kohler Co. 5 1043183-2-B
1. Valve Mounting Configurations
CAUTION: Risk of product damage. Do not mount the valve with the inlets located at the top.
Vertical and horizontal mounting options are shown above. Do not mount the valve with the inlets
pointing up or vertically with the inlets at the top.
Mounting on a Horizontal SurfaceMounting on a Vertical Surface
Do not install with inlets
pointing up or at the top.
1043183-2-B 6 Kohler Co.
2. Component Configurations
NOTE: Preprogrammed component configurations are shown; other options are possible. Use of
configurations other than the preprogrammed options will LIMIT the preprogrammed massage functions.
Massage functions that correspond with custom configurations can be programmed. Refer to the
″Digital Interface Homeowners Guide.″
The bodyspray to valve outlet ratio must be equal for all bodysprays installed. All bodysprays must
have equal flow rates; unequal flow rates will cause the massage mode to shut down. See examples
below:
Correct: For an example with four installed bodysprays; one bodyspray to one valve outlet (1:1) using four
valve outlets (Envelop).
Incorrect: For an example with four installed bodysprays; two bodysprays each installed to one valve outlet
(1:1) and the other two bodysprays installed to one valve outlet (2:1).
Wall 3
Floor
Ceiling
Wall 2
Wall 1
Wall 1
Floor
Wall 2
Frontage Envelop
Unwind
Downpour Surround
Linear
CH 12 34 5612 34 56
12 34 56
6
5
4
3
1
2
6
5
4
31
2
4
56
3
22
1
4
56
3
21
12 34 56
CH
CH
CH
If bodysprays, watertiles or watertile
showerheads are present in these outlets,
they will not cycle.
*
***
*
6
5
4
1
233
3
6
5
4
221
12 34 56
CH
12 34 56CH
Kohler Co. 7 1043183-2-B
3. Massage Cycling Configurations
Configuration 1
Frontage
Envelop
Configuration 2
Unwind
Configuration 3
= Constant on
= On while cycling
NOTE: Primary outlets and any outlets designated as
handshowers will not be included in the cycling pattern. For
installations that include both body sprays and watertiles, the
outlets designated as watertiles will not cycle.
Single
Single
Single
Dual 1
Dual
Wave
Dual 2
Wave
Dual 3
Dual 1 Dual 2
Dual 3 Wave
1043183-2-B 8 Kohler Co.
4. Massage Cycling Configurations
Configuration 4
Linear
Downpour
Configuration 5
Surround
Configuration 6
= Constant on
= On while cycling
NOTE: Primary outlets and any outlets designated as
handshowers will not be included in the cycling pattern. For
installations that include both body sprays and watertiles, the
outlets designated as watertiles will not cycle.
Single
Single Dual Wave
Single Dual Wave
Dual Wave
Kohler Co. 9 1043183-2-B
5. Custom Component Configurations
Draw in the components for your custom shower.
Draw lines from the valve to each component. Be aware that:
•Outlet 1 is always recommended to be the primary showerhead.
•The installer must determine the desired sequence for Single mode and plumb the ports to the
bodysprays accordingly.
•Custom mode will allow the user to select a different water outlet as the primary showerhead, but it
is not recommended.
•In Custom mode, the bodysprays will cycle up the solenoid bank regardless of which port is the
primary outlet.
Wall 3
Floor
Ceiling
Wall 2
Wall 1
Wall 1
Floor
Wall 2
CH 12 34 56
12 34 56CH
1043183-2-B 10 Kohler Co.
Andere Handbücher für K-682
3
Inhaltsverzeichnis
Andere Kohler Steuereinheit Handbücher
Kohler
Kohler 1216612 Bedienungsanleitung
Kohler
Kohler K-304 Montageanleitung
Kohler
Kohler K-10666 Betriebsanleitung
Kohler
Kohler K-402 Bedienungsanleitung
Kohler
Kohler TOUCHLESS K-13686 Bedienungsanleitung
Kohler
Kohler GM77177-KP1-QS Bedienungsanleitung
Kohler
Kohler K-528 Bedienungsanleitung
Kohler
Kohler Rite-Temp K-8304-K Bedienungsanleitung
Kohler
Kohler AQUA TURBO 360 Bedienungsanleitung
Kohler
Kohler DTV+ Konnect K-97999-NA Bedienungsanleitung
Kohler
Kohler rada VZ1 10 Bedienungsanleitung
Kohler
Kohler 28139T-DR Bedienungsanleitung
Kohler
Kohler K-528 Bedienungsanleitung
Kohler
Kohler K-10970 Montageanleitung
Kohler
Kohler K-175 Montageanleitung
Kohler
Kohler DTV+ Montageanleitung
Kohler
Kohler TAUT 73193T-4CD Bedienungsanleitung
Kohler
Kohler BEAM K-77691K-G Bedienungsanleitung
Kohler
Kohler K-308 Bedienungsanleitung
Kohler
Kohler K-13516X Montageanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
