Kohler K-19537P Bedienungsanleitung

Installation Guide

Thermostatic Wall-Mount Valve

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-19537P

1084859-2-C

IMPORTANT INSTRUCTIONS

READ AND SAVE FOR THE

CONSUMER

WARNING: Risk of scalding or other severe injury.

CAUTION: Risk of scalding hazard. This device has been

calibrated at the factory to ensure a safe maximum water

temperature. Any variance in settings or water inlet

conditions from those used during factory calibration may

raise the discharge temperature above the safe limit, and may

present a scalding hazard.

•Before completing installation, the installer must set the

maximum water temperature setting of this valve to minimize the

risks associated with scalding hazards according to ASTM F 444.

The installer is responsible for adjusting the maximum water

temperature of this valve according to instructions.

This valve meets or exceeds ANSI A112.18.1 and ASSE 1016.

If you do not understand any of the temperature adjustment

instructions in this document, in the United States please contact our

Customer Service Department at 1-800-4KOHLER. Outside the U.S.,

please contact your distributor.

IMPORTANT NOTICE: Please ﬁll in the blanks in the information box

in the Homeowners Guide and on the valve label. Retain the

Homeowners Guide for future reference.

•The valve is calibrated to 104°F (40°C) at the ﬁrst stop position,

and the maximum temperature limit stop is positioned so the

outlet water temperature does not exceed 120°F (49°C).

•Factory calibrated inlet conditions are:

Hot and cold water pressure = 45 psi (3.2 kg/cm

)

Hot water supply temperature = 145°F (63°C)

Cold water supply temperature = 65°F (18°C)

•If inlet conditions differ from those used during factory

calibration, it may be necessary to re-calibrate the valve after

installation. The installer must check the mixed ﬂow

temperature after installation, and adjust the valve as needed

according to the instructions.

1084859-2-C 2 Kohler Co.

Tools and Materials

Before You Begin

CAUTION: Risk of personal injury. To eliminate the risk of

scalding, the water temperature should never be set above

120°F (49°C).

Observe all local plumbing and building codes.

For installations with tile or marble ﬁnished surfaces, it may be

necessary to extend the supply lines after the elbows. Contact

customer service about the availability of a deep rough-in kit for

this product.

Shut off the main water supply.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

2x4 Lumber Thermometer Phillips Screwdriver

Level

Plus:

• 1/2" Drop Ear Elbows

• 3/4" Straight Thread Pipe Caps

• Rags

Tape

Measure

Adjustable

Wrench

Sealant

Tape

Kohler Co. 3 1084859-2-C

Roughing-In

NOTE: For tile and marble, it may be necessary to extend the

supply lines after the elbows. If this is the case, be sure the supplied

offset pipe nipples extend 1-9/16″(4 cm) to 1-3/4″(4.5 cm) from the

ﬁnished wall surface.

G1/2-14

1/2-14 NPT

5-7/8" (15 cm)

11-7/16" (29.1 cm)

Supply Lines

1/8" (3 mm) -

1/2" (1.3 cm)

1/2-14 NPT

Elbow

4-1/4"

(10.7 cm) Finished

Wall

2-3/4"

(7 cm) D.

3-1/8" (8 cm)

1084859-2-C 4 Kohler Co.

1. Prepare the Site

Rough-in the Plumbing

NOTICE: For exterior wall installations, ensure proper wall

insulation to prevent frozen pipes.

Attach a 2x4 brace between two studs to support the supply lines.

The brace should be positioned so the face of the 1/2-14 NPT

supply elbows will be recessed 1/8″(3 mm) to 1/2″(1.3 cm)

within the ﬁnished wall.

NOTICE: Tile or stone covered walls may require an extension of

the supply line.

Position the supply lines 5-7/8″(14.9 cm) between the centerlines,

then attach a brass elbow to each supply line.

Verify the elbows are level with one another and the opened end

faces are recessed 1/8″(3 mm) to 1/2″(1.3 cm) behind the

planned ﬁnished wall surface.

Secure the elbows and supply lines to the 2x4.

Apply sealant tape to each pipe nipple.

Escutcheon

Supply Lines

Pipe Nipple

Apply sealant tape.

2x4

5-7/8"

(14.9 cm)

1/8" (3 mm) -

1/2" (1.3 cm)

Stud

2x4

Brace

Finished

Wall

Elbow

Kohler Co. 5 1084859-2-C

Prepare the Site (cont.)

Secure a pipe nipple to each elbow, maintaining 5-7/8″(14.9 cm)

distance between the nipple centerlines.

Conﬁrm the Rough-in Plumbing

Temporarily thread an escutcheon onto each pipe nipple until

they are in a position that will be ﬂush with the planned ﬁnished

wall.

Slide the faucet assembly onto the pipe nipples.

Verify the valve assembly is properly aligned and level. If

necessary, make adjustments by repositioning the elbows or by

offsetting the pipe nipples.

NOTICE: If a pipe nipple needs to be loosened for proper

alignment, be sure to remove the nipple, apply sealant tape and

reinstall to the desired location to avoid leakage.

Remove the valve assembly and escutcheons.

Site Checkout

Flush the water lines.

Cap the pipe nipples (or temporarily install the valve) and check

for leaks at the connections.

Complete the ﬁnished wall.

1084859-2-C 6 Kohler Co.

2. Mount the Valve

Remove the caps from the pipe nipples. Do not allow the nipples

to rotate.

Verify that the pipe nipples extend between 1-9/16″(4 cm) and

1-3/4″(4.5 cm) from the ﬁnished wall.

Thread an escutcheon onto each pipe nipple until ﬂush against

the wall. Apply sealant between the escutcheon and the wall.

Insert a washer into each valve inlet.

Slide the valve onto the pipe nipples.

Washer

Escutcheon

1-9/6" (4 cm) –

1-3/4" (4.5 cm)

Pipe

Nipple

Kohler Co. 7 1084859-2-C

3. Complete the Installation

NOTE: Place a rag around the attached nut before tightening with a

wrench. This will protect the ﬁnish on the valve.

Using an adjustable wrench, wrench tighten the nuts attached to

the valve. Do not overtighten.

Turn the volume control to the OFF position.

Verify that all connections are tight.

Turn on the main water supply.

Check all connections for leaks. Repair as needed.

Turn the volume control to the ON position to run water through

the valve. Allow the water to run through the outlet to remove

any debris.

Turn the volume control to the OFF position.

Attach the handshower hose to the outlet. Refer to the

handshower manufacturer’s installation instructions.

Tighten the escutcheons.

Handshower Hose

Wrench tighten the nuts.

1084859-2-C 8 Kohler Co.

Optional Temperature Limiting Adjustment

CAUTION: Risk of personal injury. To eliminate the risk of

scalding, the water temperature should never be set above

120°F (49°C).

NOTE: The detent position on the temperature control has been

calibrated to a shower temperature of approximately 104°F (40°C) to

105°F (41°C). If the temperature is not between 104°F (40°C) to 105°F

(41°C) at the detent position, follow the procedures below.

Turn the volume control on and turn the temperature control to

the full ″37″reference mark.

Let the water run for several minutes. Position a thermometer in

the water stream and check the maximum temperature.

Turn the temperature control to the full cold position, then slowly

turn the temperature selector toward you until the proper

maximum hot temperature is obtained.

NOTICE: Once the proper maximum temperature is obtained, do

not turn the temperature control.

NOTICE: Close the bath drain before removing the valve

components.

Using your ﬁngers, remove the plug button.

Using a Phillips screwdriver, remove the screw.

Using your ﬁngers, remove the washer.

Without rotating the temperature control, carefully remove the

temperature control from the spindle.

Reference Mark

Spindle

Temperature Control Screw

Plug Button

Washer

Kohler Co. 9 1084859-2-C

Optional Temperature Limiting Adjustment (cont.)

Without rotating the temperature control, reinstall the

temperature control onto the spindle, aligning the ″37″reference

mark with the reference mark on the valve.

Reinstall the washer, screw, and plug button into the temperature

control.

Recheck the maximum hot temperature.

1084859-2-C 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Steuereinheit Handbücher

Kohler

Kohler K-728 Montageanleitung

Kohler

Kohler DTV+ Montageanleitung

Kohler

Kohler K-10673 Betriebsanleitung

Kohler

Kohler K-400 Bedienungsanleitung

Kohler

Kohler K-T10669 Montageanleitung

Kohler

Kohler K-10675 Bedienungsanleitung

Kohler

Kohler K-528 Bedienungsanleitung

Kohler

Kohler Rite-Temp K-8300-PX Bedienungsanleitung

Kohler

Kohler K-10956 Betriebsanleitung

Kohler

Kohler K-175 Bedienungsanleitung

Kohler

Kohler K-528 Bedienungsanleitung

Kohler

Kohler ENGLEFIELD K-98095X Montageanleitung

Kohler

Kohler K-402 Montageanleitung

Kohler

Kohler K-408 Montageanleitung

Kohler

Kohler K-14677 Montageanleitung

Kohler

Kohler K-407 Bedienungsanleitung

Kohler

Kohler K-10970 Montageanleitung

Kohler

Kohler 1216612 Bedienungsanleitung

Kohler

Kohler K-10959 Bedienungsanleitung

Kohler

Kohler K-13516X Montageanleitung

Kohler

Kohler K-10668 Montageanleitung

Kohler

Kohler DTV+ Konnect K-97999-NA Bedienungsanleitung

Kohler

Kohler Rite-Temp K-8304-K Bedienungsanleitung

Kohler

Kohler K-10949 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung