Kohler ADAGIO K-731T Bedienungsanleitung

-1-

368 201419

ã, 2006

BEFORE YOU BEGINBEFORE YOU BEGIN

ADAGIO

SOISSONS

K-731T/K-731T-NR/K-731T-GR

K-940T/K-940T-GR/K-941T/K-941T-GR

K-943T/K-943T-GR

INSTALLATION INSTRUCTIONS

ENAMELED CAST IRON BATH

PRODUCT REQUIREMENTS

1006291-T01-C

WARNING: Risk of personal injury.

NOTICE:

Cast iron bathes are extremely heavy. Wear

appropriate safety equipment when installing these

products.

Observe all local plumbing codes.

Please read these instructions carefully to

familiarize yourself with the required tools, materials,

and installation sequences. Follow the sections that

pertain to your particular installation. This will help

you avoid costly mistakes. In addition to proper

installation, read all operating and safety instructions.

All information is based on the latest product

information available at the time of publication.

Kohler China Ltd. reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning,

and warranty information-please leave these

instructions for the consumer.

A. Summary Of Key Requirements

Observe all local plumbing codes.

Install the unit to a level subfloor.

Provide properly-dimensioned framing.

Baths are designed for a variety of installations,

depending upon the model chosen.

B. Product Inspection

Uncrate and inspect bath for damage. Leave all

materials in the crate during construction to prevent

damage.

-2-

ROUGHING-IN

A. Roughing-in Notes

Fixture dimensions are nominal and conform to

tolerances in ANSI Standard A112.19.1M.

B. Determine Rough-in

Measure the height, width, and depth of the bath. Verify

these dimensions with those on this page.

Allow clearance at the drain hole location in the flooring,

if necessary.

A112.19.1M

UNIT: mm

800

400

294

1700

117

WEIGHT: 125Kg

ADAGIO

UNIT: mm

SOISSONS

700

350

290

110

SOISSONS 940T/K-940T-GR K-941T/K-941T-GR

L 1700mm 1500mm

WEIGHT 90Kg 84Kg

K- K-943T/K-943T-GR

1600mm

115.4Kg

* The rim width of the drain side is 110-118mm, Please select the faucet with matching spout for the bath.

* 110-118mm

418

476

1006291-T01-C

-3-

C. Accessory Information

ADAGIO

SOISSONS

Grip Rail..........8598T-CP(For 731T/731T-GR)

Grip Rail

.......................8599T(For 940T-GR/ )941T-GR/943T-GR

.................8598T-CP( 731T/731T-GR)

..................8599T( 940T-GR )/941T-GR/943T-GR

1006291-T01-C

INSTALLATION REQUIREMENTSINSTALLATION REQUIREMENTS

C. Clearance Requirements

Check the rough-in and room dimensions to provide

adequate available space for the bath unit.

D. CUT-OUT Dimensions

K-731T ADAGIO 1662 762mm

K-940T/K-940T-GR SOISSONS 1662 662mm

K-941T/K-941T-GR SOISSONS 1462 662mm

K-943T//K-943T-GR SOISSONS 1562 662mm

K-731T 1662 762mm

K-940T/K-940T-GR 1662 662mm

K-941T/K-941T-GR 1462 662mm

K-943T/K-943T-GR 1562 662mm

Adjustable pipe

wrench

Rule

Level

Safety shoes

Safety glasses

Square

Pliers

Plumbers putty

Wall coverings, as necessary

Silicone sealant

Protective covering for

bathtub or card board

Metal shims

B. Materials RequiredA. Tools Required

SITE REQUIREMENTSSITE REQUIREMENTS

A. Old Bath Removal (If Necessary)

Disconnect the drain at the trap. Remove the old wall

material. Slip boards under the old bath feet to protect

the floor, and slide the old bath out of the recess as

illustrated.

A. ( )

Old Bath Floor Protection Boards

B. Subfloor Preparation

Check the flooring under the bath, and make repairs as

needed. Make sure the subfloor is level and water proof.

C. Plumbing Preparation

Position the plumbing according to rough-in dimensions.

Cap the supplies and check for leaks.

-4-

BEFORE INSTALLING UNITBEFORE INSTALLING UNIT

A. The following installation practices

to avoid any potential damage to the

enamel finish.

WARNING:

must be

followed

Failure to follow the manufacturers

recommended installation method may result in

damage to the enamel surface.

Do not use sharp objects or metal tools when

handling the bath, especially around the rim area.

Use a clear protective plastic film over tub rim as

well as the bottom of tub to safeguard from dirt and

silicone during the installation process.

For correct installation, bath rim should not come in

direct contact with the walls or horizontal surfaces to

avoid transmission of noise and vibration as well as

potential cracks in the enamel finish.

The necessary gap between bath rim and the wall is

2 mm horizontally and 4 mm vertically. Refer to

figures 1, 2, and 3 below.

Before setting-in the bath, apply a sanitary quality

silicone filler on all surfaces to come in contact with

the bath rim.

Set the bath in its correct position.

123

B. Partially Install Bath Drain

Install the drain on the bath according to the drain

manufacturers instructions.

Silicone Filler

Bath

Wall

Silicone Filler

Tiling

Wall

Bath

Silicone Filler

Bath

UNIT: mm

Fig.1

1Fig.2

INSTALL THE BATHINSTALL THE BATH

A1. Installation of Bath with Adjustable

Slide the new bath into position.

Insert the drain tailpiece into the trap.

Level the bath by positioning metal shims and bricks

under the bath feet, and ensure there is enough space

for the drain. Attention: The metal shims are necessary

to avoid cracking of bricks. Check for level along the

top of the side of the bath and across the drain end.

The bath may have to be moved in and out of the

recess area until it is shimmed properly, if the support

feet are not accessible from the back or side.

Level

Fig.3

Height

1006291-T01-C

A2. Through the Floor Drain Bath

Installation

A2.

Slide the new bath into position to verify the drain

location and the stud fit. Cut a minimum 152 x 305 mm

hole in the floor for the drain connection.

152 305mm

Use 25~30 Kg dry cement and sand mix. Add water to

make a paste mortar. Remove the tub. Cover the

installation area with the mortar starting from the middle

of the tub as shown. The height of the mortar should

reach the bottom of the rub.

DO NOT CLOG THE DRAIN HOLE.

Place the tub onto the mortar. Insert the drain tailpiece

into the trap.

Make sure that the bottom of the tub is pressed into

mortar in order to secure the tub. Insert two wood

wedges under the tub to support the weight of the tub

until the mortar hardens. (Wedges will remain in the

mortar.) Frequently check the level of the tub.

25~30

NOTE:

A1.

Metal Shim

Level

Paste Mortar

Wood Wedge

Middle of Bath

Drain Hole

Brick

1006291-T01-C -5-

C. Finish Bath Area Construction

NOTE: An access panel is essential for future

maintenance.

Possible framing arrangements are illustrated below.

Use the framing construction appropriate for your

particular bath model. Some modifications may be

needed for other types of construction, if preferred.

If an apron wall without a ledge is desired, the finished

apron wall surface must be 2 mm under the bath rim.

2mm

Recommended For Drop-in Models

1) Corner Installation

The suggested framing construction is illustrated.

2) Recess Installation

The suggested framing construction is illustrated.

B. Install Plumbing

CAUTION: Risk of damage to bath bottom and subfloor.

Ensure a watertight seal on the bath drain connections.

For through the floor drain installation, when the bath

is securely positioned, connect the drain to the trap.

See Fig. A.

2) Install the faucet valving and spout tee. Open the hot

and cold water valves, and check the supply

connections for leaks.

Run water into the bath, and check the drain

connections for leaks.

Connect Here

Fig. A

1006291-T01-C -6-

INSTALL THE GRIP RAILINSTALL THE GRIP RAIL

For ADAGIO Bath 731T, 731T-GR

Place the gasket (1) onto the grip rail(2). Make sure the

gasket is matching the contour of the grip rail. Insert

both screws(3) into the holes through the grip rail and

the gasket.

Thread screws (3) into the nut pre-installed on the side

of bathtub. Tighten the screw snugly to secure the grip

rail.

Repeat above procedures for the other grip rail.

731T, 731T-GR

(1) (2)

(3)

(1)

(3)

(2)

3) Peninsular Installation

The suggested framing construction is illustrated.

1006291-T01-C

For SOISSONS 940T-GR, 941T-GR, 943T-GR

940T-GR, 941T-GR, 943T-GR

Place the gasket (6) onto the grip rail (7). Insert the

screw (8). Position the grip rail with gasket so that the

hole lines up with the hole on the nut pre-installed on

the side of bath tub.

Thread the screw (8) into the hole of the grip rail.

Tighten the screw snugly to secure the grip rail. Snap

the cap (9) into each hole. Repeat above procedures

for the other grip rail.

(6) (7) (8)

(8)

(9)

-7-

COMPLETE FINISH WALLCOMPLETE FINISH WALL

CAUTION: Risk of product damage. Do not

support the weight of the bath by the rim.

Install the ceramic or marble tiles. Seal the joints

between the bath rim and the finished tiled wall using

silicone sealant. RTV (Room Temperature Vulcanizing)

sealant is recommended.

CLEAN-UP AFTER INSTALLATIONCLEAN-UP AFTER INSTALLATION

When cleaning up after installation, do not use abrasive

cleansers as they may scratch and dull the surface.

Use warm water and liquid, non-abrasive detergent to

clean the surface.

Stubborn stains, paint, or tar can be removed with

mineral spirits. Do not use cleaners containing solvent.

Plaster can be removed by scraping with wood edge.

Do not use metal scrapers, wire brushes, or other metal

tools. One of the powder type detergents may be used

on a damp cloth to provide mild abrasive action to the

residual plaster.

-8-

1006291-T01-C

-9-

IMPORTANT CONSUMER INFORMATIONIMPORTANT CONSUMER INFORMATION

Safeguard ASME/ANSI

A112.19.1M

pH 3 8 (

)

Housekeeping Responsibilities

The Safeguard slip resistant surface on this bathtub

meets or exceeds the requirements of ASME/ANSI

for slip resistance.

DANGER!! Improper maintenance or cleansers may

permanently remove the slip resistant

surface on Kohler bathtubs.

NOTICE: All housekeeping and maintenance

employees must be trained in the proper

cleaning of Kohler bathtubs. Post a copy of

this notice in a readily-visible location.

DO NOT use steel wool, wire brushes, metal scrapers

or abrasive sponge pads to clean a Kohler

bath tub.

DO NOT use buffing machines on the slip resistant

surface.

DO NOT use high alkaline or strong acid cleansers.

DO NOT use abrasive cleansers.

Use only non-abrasive cleansers and a soft nylon

brush to clean the slip resistant surface.

When using commercial cleansers, use cleansers

with a pH of between three and eight.

Follow cleanser manufacturer instructions very

carefully.

A112.19.1M

1006291-T01-C

LIMITED ONE-YEAR WARRANTYLIMITED ONE-YEAR WARRANTY

(

)

()

138

200021

Plumbing Fixtures and Fittings Limited

One-year Warranty

Kohler plumbing fixtures and fittings are warranted to

be free of manufacturing defects.

This product is warranted for one year from date of

purchase. Kohler China will be responsible for any

problems caused by manufacturing defects provided

with the invoice. Kohler China will, at its election, repair,

replace or make appropriate adjustment where Kohler

China inspection discloses any such defects occurring

in normal usage within one year after purchase.

Implied warranties including that of merchantability and

fitness for a particular purpose are expressly limited in

duration to the duration of this warranty, Kohler China

disclaims any liability for special, incidental or

consequential damages. Damages to the product

caused by misuse, abuse and installation that is not in

accordance with the owner's manual are not covered

by this warranty.

To obtain quick warranty service, please contact your

dealer, or write to Kohler China. (Original sales receipt

must be provided as the proof of purchase.)

Kohler China Investment Company Ltd.

Central Customer Service Center

19/F, Shanghai Square, 138 Huai Hai

Road, Luwan District, Shanghai, PRC

Zip Code: 200021

This is our exclusive written warranty.

-10-

1006291-T01-C

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-13132-3A Montageanleitung

Kohler

Kohler C3-050 Bedienungsanleitung

Kohler

Kohler K-2219 Bedienungsanleitung

Kohler

Kohler K-7397 Montageanleitung

Kohler

Kohler Flipside 17492T Bedienungsanleitung

Kohler

Kohler K-T13140 Bedienungsanleitung

Kohler

Kohler PURIST 7507T-B4 Bedienungsanleitung

Kohler

Kohler K-9530 Montageanleitung

Kohler

Kohler WELLINGTON WATERGUARD K-3415 Bedienungsanleitung

Kohler

Kohler K-4904X-ER Montageanleitung

Kohler

Kohler 84625 Handbuch

Kohler

Kohler 23472T-4 Bedienungsanleitung

Kohler

Kohler K-702200 Montageanleitung

Kohler

Kohler K-14663 Montageanleitung

Kohler

Kohler Stillness 954T-4 Bedienungsanleitung

Kohler

Kohler K-1188BR Bedienungsanleitung

Kohler

Kohler K-73194X-4A Montageanleitung

Kohler

Kohler K-19797T Bedienungsanleitung

Kohler

Kohler K-10481 Bedienungsanleitung

Kohler

Kohler K-7331 Montageanleitung

Kohler

Kohler K-14675X Bedienungsanleitung

Kohler

Kohler Glenbury Quiet-Close K-4733 Bedienungsanleitung

Kohler

Kohler K-T14419 Montageanleitung

Kohler

Kohler Clearflo K-7160-TF Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung