Kohler K-9530 Montageanleitung

Installation and Care Guide

Two-Way Diverter

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

K-9530

1229813-2-A

Tools and Materials

Before You Begin

WARNING: Risk of personal injury. This product is a

diverter valve only and should never be used as a shut-off

valve. Doing so would allow cross ﬂow between the hot and

cold water supplies and create a serious scalding hazard.

Observe all local plumbing and building codes.

Shut off the main water supply.

Provide an access panel for all installations.

Carefully read this entire instruction manual before beginning the

installation; the illustrations do not show all possible

conﬁgurations.

This diverter can be installed to decks with a maximum thickness

of 1-1/4″(32 mm).

Carefully inspect waste and supply tubing for any sign of

damage. Replace if needed.

You can extend the distance between the water source and the

braided hose connection with 1/2″copper piping below the rim

of the bath/whirlpool, but it may not be safe or practical. A long

run of piping will mean a long run of room-temperature standing

water when the handshower is ﬁrst activated for use.

This diverter can be used in either a deck-mount or wall-mount

installation. Refer to the ″Diverter Conﬁgurations″section for any

special considerations.

Do not install spouts with ﬂow restrictors or handheld shower

units on the large (5/8″OD) bath outlet.

• Supply piping,

connectors, and caps

Plus:

Adjustable

Wrench

Tape

Measure

3/32" Hex

Wrench

Solder

Propane

Torch

Drill and

Hole Bit

1229813-2-A 2 Kohler Co.

Before You Begin (cont.)

The KOHLER two-way diverter is designed for use with

KOHLER non-diverting bath spouts.

Remove all internal components of the diverter valve before

soldering. Kohler Co. recommends soldering supply and optional

outlet connections to avoid potential leakage.

Kohler Co. 3 1229813-2-A

1. Diverter Conﬁgurations

Conﬁgurations for Deck-Mount Installations

The small port is for the handshower (or showerhead).

The port directly across from the small port is for the bath spout.

Default ﬂow is through this port.

The remaining two ports are for the hot and cold water inlet

supplies. They are interchangeable. If only one of these ports is

needed, cap the other port.

Conﬁgurations for Wall-Mount Installations

When diverting between the bath spout and handshower (or

showerhead):

The small port is for the handshower (or showerhead).

The port directly across from the small port is for the bath spout.

Default ﬂow is through this port.

Cartridge

3/4"-14

NPSM

Thread

1/2"-14 NPSM

Thread

Spout 1/2" Nominal

(5/8" OD)

Handshower 3/8"

Nominal (1/2" OD)

Hot or

Cold 1/2"

Nominal

(5/8" OD)

Hot or

Cold 1/2"

Nominal

(5/8" OD)

Deck-Mount Wall-Mount

From Mixer

Handshower or

Showerhead

Review instructions for

specific configurations.

1/2" Nominal (5/8" OD)

3/4"-14 NPSM Thread

3/8" Nominal (1/2" OD)

1/2"-14 NPSM Thread

Showerhead

or Bath Spout

Cartridge

From Mixer

1229813-2-A 4 Kohler Co.

Diverter Conﬁgurations (cont.)

The remaining two ports are for the hot and cold water inlet

supplies. They are interchangeable. If only one of these ports is

needed, cap the other port.

When diverting between the showerhead and handshower:

The small port is for the handshower.

The port directly across from the small port is for the

showerhead. Default ﬂow is through this port.

The remaining two ports are for the inlet supply. They are

interchangeable. If only one of these ports is needed, cap the

other port.

Kohler Co. 5 1229813-2-A

2. Piping Conﬁgurations

Verify the location of the components and the orientation of all

ports.

Decide in advance on the location and orientation of the diverter.

The locations of the shower and the handshower as well as the

direction in which the inlets/outlets point will affect the piping

and connectors needed.

Allow clearance for the valve outlets, handles, and handshower

hoses. For use with an optional spout, also allow clearance for the

spout connection.

You can extend the distance between the diverter and the braided

hose connection with 1/2″copper piping below the rim of the

bath/whirlpool, but it may not be safe or practical. A long run of

piping will mean a long run of room-temperature standing water

when the handshower is ﬁrst activated for use.

Secure long runs of piping to the underside of the deck or rim. If

the piping cannot be secured at a point near the diverter, secure

the piping from underneath with lumber or other suitable

support.

Jog in Piping

Jog in Piping Diverter

Mixer Valve

To Handshower

To Shower

Wall-Mount Deck-Mount

1229813-2-A 6 Kohler Co.

3. Preparation

Provide an access panel for all installations.

Allow for access to the connection between the shower

high-pressure hose and the shower interlock hose.

NOTE: For easiest installation, do not install the bath unit until all

soldering (except supplies) is complete. Then install the bath and

connect the supplies.

If used, install the bath spout shank at this time according to the

spout installation instructions. If possible, do not install the

ﬁnished trim until all other installations and construction are

completed.

For spouts with a supply tee: Add an adapter and a 1/2″copper

tube. Secure with solder. Cap to close the extra port.

Install the valve bodies according to the valve body installation

instructions.

Loosely secure the valve bodies.

Follow the handle installation instructions to temporarily

assemble the handles to adjust the valves to the proper height.

Adjust the valve height before connecting the lines to the diverter

or supply.

NOTE: The cartridge assembly is easier to remove before the

diverter is installed. You can remove the assembly now or after the

diverter installation.

Spout

Supply

Tee

1/2"

Nominal

Copper Cap

1/2"

Nominal

Copper

Adapter

(Supplied

with Spout)

Kohler Co. 7 1229813-2-A

Preparation (cont.)

Use a wrench to loosen the cartridge assembly from the diverter

body. Continue to unthread the assembly to remove.

Set the assembly aside. Protect the seals and O-rings from

becoming dirty, damaged, or misaligned.

1229813-2-A 8 Kohler Co.

4. Install the Diverter

For Finished Deck Installations

At the diverter install location, drill a 1-1/2″(38 mm) hole.

For All Installations

NOTE: You may need assistance to align and secure the diverter.

Thread the mounting nut all the way down onto the diverter

body.

Slide the friction washer followed by the rubber washer over the

diverter body and down to the mounting nut.

Insert the diverter body through the deck/rim/wall.

Slide the washer onto the diverter body.

Thread the escutcheon onto the diverter body until the

escutcheon bottoms out on the diverter body. This will allow

ample clearance for proper handle function.

Align the inlets and outlets.

Hand tighten the mounting nut.

Deck/Rim

Escutcheon

Washer

Brass

Mounting

Nut

Friction

Washer

Rubber

Washer

Kohler Co. 9 1229813-2-A

5. Complete the Diverter Installation

CAUTION: Risk of product damage. Verify that the diverter body

is secure before removing the cartridge. If not secured, the process

of removing the cartridge may damage the pipe and connections.

CAUTION: Risk of product damage. Excessive heat will damage

the internal plastic components. Do not apply excessive heat while

soldering. Direct the torch ﬂame away from the brass body. Only

apply direct heat to the connectors and extensions.

IMPORTANT! If there is limited access to the solder connections, or

if any other risk of excessive heat being applied to the brass body

exists, remove the cartridge prior to soldering. If you remove the

cartridge, protect the seals and O-rings from becoming dirty,

damaged, or misaligned.

IMPORTANT! Do not apply excessive heat while soldering. Direct

the torch ﬂame away from the brass body.

IMPORTANT! Only apply direct heat to the connectors and

extensions.

If not already removed, remove the diverter cartridge assembly.

Dry ﬁt all piping and connectors.

Solder piping for the optional spout or wall shower.

Connect the hot and cold lines from the valves to the diverter.

Note: Provide Diverter Support

Diverter

Valve Body

Diverter

Cartridge

Escutcheon

Deck/Rim Setscrew

Stem

Escutcheon

Diverter Handle

1229813-2-A 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Mira Escape Thermostatic 9.0 kW J95Hb/c Bedienungsanleitung

Kohler

Kohler STRAYT 37331-4 Bedienungsanleitung

Kohler

Kohler Symbol Rite-Temp K-T18488 Bedienungsanleitung

Kohler

Kohler K-2419 Montageanleitung

Kohler

Kohler K-R77748 Montageanleitung

Kohler

Kohler Sunstruck K-24009-GH Bedienungsanleitung

Kohler

Kohler K-411 Bedienungsanleitung

Kohler

Kohler K-2367 Bedienungsanleitung

Kohler

Kohler K-5024-T Bedienungsanleitung

Kohler

Kohler MARSTON K-2766 Bedienungsanleitung

Kohler

Kohler K-10958 Bedienungsanleitung

Kohler

Kohler K-9486 Bedienungsanleitung

Kohler

Kohler K-4761 Bedienungsanleitung

Kohler

Kohler EVOKE 6332T-B4 Bedienungsanleitung

Kohler

Kohler K-8855 Bedienungsanleitung

Kohler

Kohler K-393 Bedienungsanleitung

Kohler

Kohler K-8207 Bedienungsanleitung

Kohler

Kohler K-7744 Bedienungsanleitung

Kohler

Kohler Margaux K-16230-4 Bedienungsanleitung

Kohler

Kohler K-5293 Bedienungsanleitung

Kohler

Kohler K-4108 Bedienungsanleitung

Kohler

Kohler K-7397 Bedienungsanleitung

Kohler

Kohler K-T314 Bedienungsanleitung

Kohler

Kohler K-14402 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung