Kohler K-13132 Bedienungsanleitung

Installation Guide

Widespread Lavatory Faucets

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page“ Français-1”

Español, página“ Español-1”

K-13132

1033980-2-A

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

Replace waste or supply tubing if necessary.

For new installations, install the faucet before installing the

lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Adjustable

Wrench Plumbers

Putty Sealant

Tape Pipe

Sealant

1033980-2-A 2 Kohler Co.

1. Spout Installation

Apply a bead of plumbers putty or other sealant to the underside

of the spout escutcheon according to the putty manufacturer’s

instructions.

Locate the center hole and insert the spout.

Install the metal washer and nut.

Securely tighten the nut with a wrench. Do not overtighten.

Remove any excess putty or sealant.

Remove and retain the guide tube nut and O-ring from the

supply tee.

Insert the washer and gasket into the supply tee.

Thread the supply tee onto the spout until hand tight.

Hold the spout in place and tighten the supply tee with a wrench

until it is aligned side to side. Do not overtighten.

Slip the O-ring over the lift rod and thread the guide tube nut

onto the supply tee.

Tighten the guide tube nut on the supply tee with a wrench. Do

not overtighten.

Nut

Washer

Gasket

O-Ring

Apply

Plumbers

Putty.

Metal

Washer

Supply

Tee

Guide

Tube Nut

Spout

Lift Rod

Kohler Co. 3 1033980-2-A

2. Handle Valve Installation

NOTE: The valve body marked ″Cold″(with blue lettered tape

attached to the tube) should be installed to the right of the faucet.

Apply a bead of plumbers putty or other sealant to the underside

of the escutcheons according to the manufacturer’s instructions.

From the top of the lavatory, insert the cold and hot valve bodies

into the mounting holes. Make sure that the body marked

″COLD″is installed in the right-hand hole as viewed from the

front of the lavatory.

Install a washer and a nut onto the underside of each valve body.

Rotate each valve body until the copper tubing faces towards the

outside of the lavatory.

While holding the valve bodies in place, securely tighten the nuts

with a wrench. Do not overtighten.

Remove any excess putty or sealant.

Install the O-ring on the hose and thread each hose into the

handle body outlet.

Tighten the hose connections on the handle body with a wrench.

Do not overtighten.

Loop the hoses as shown and connect them to the supply tee

inlets. Do not use thread sealant. Do not overtighten.

Nut

Washer

Hose

Handle

Body

Outlet

O-Ring

Copper

Tube

Supply

Tee

Flexible

Hose Supply

Tee

Flexible

Hose Supply

Tee

Flexible

Hose Supply

Tee

Flexible

Hose Supply

Tee

Flexible

Hose

1033980-2-A 4 Kohler Co.

3. Drain Style

Refer to the illustrations above to determine the drain style you

received with your faucet.

Please follow the instructions for your drain style.

Style A Drain Style B Drain

Kohler Co. 5 1033980-2-A

4. Drain Installation-Style A

Remove the protective material from the ﬂange.

Wrap the bottom 2/3 of the ﬂange threads with three layers of

sealant tape.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Insert the ﬂange into the ﬁxture drain hole.

Assemble the gasket (tapered side up) and washer to the ﬂange

and partially thread the nut to the ﬂange. Do not fully tighten the

nut at this time.

Install the body washer and drain body with the seal hole facing

the back of the ﬁxture and securely tighten the nut. Use care to

avoid scratching the ﬁnish.

Remove any excess putty or sealant.

Insert the stopper into the ﬂange.

Insert the seal into the seal hole on the body.

Seal

Stopper

Lavatory

Screw

Spring

Clip Gasket

NutNut

Link

Rod Seal

Flange

Apply Plumbers

Putty.

Apply 3 layers of

sealant tape to

bottom 2/3.

Washer

Body Washer

Drain Body

1033980-2-A 6 Kohler Co.

5. Complete Drain Installation-Style A

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper. Secure

with the body nut.

Remove and adjust the stopper so it lifts about 3/8″(1 cm) when

opened. To adjust, loosen the stopper nut and shorten or lengthen

the stopper as needed. Tighten the stopper nut.

Apply three layers of thread tape and a small bead of pipe

sealant to the tailpiece threads.

Thread the tailpiece to the body and tighten securely.

Slide one end of the clip onto the rod. Slide the link onto the rod

with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the faucet and then into the

hole in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

above the lift rod hole.

Faucet

Rod

Clip

Thumb

Screw

Link

Kohler Co. 7 1033980-2-A

6. Drain Installation-Style B

Remove the protective cover from the ﬂange.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Assemble the nut, ﬂat washer, and tapered gasket (tapered side

up) fully onto the body.

From the underside of the ﬁxture, insert the drain body up into

the drain hole.

From the top of the ﬁxture, securely hand tighten the ﬂange onto

the drain body.

Make sure the drain body seal hole is facing the back of the

ﬁxture, and securely tighten the nut.

Remove any excess putty or sealant.

Apply Plumbers

Putty.

Flange

Gasket

Washer

Nut

Drain Body

Fixture

1033980-2-A 8 Kohler Co.

7. Complete Drain Installation-Style B

Press the seal into the seal hole on the body.

Insert the stopper into the ﬂange.

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper. Hand

tighten the body nut.

Remove and adjust the stopper as needed so it lifts about 3/8″(1

cm) when opened. To adjust, rotate the threaded stopper rod in or

out as needed. Retighten the stopper nut.

Apply thread sealant tape to the tailpiece threads, and thread the

tailpiece to the body. Tighten the tailpiece securely.

Slide one end of the clip onto the rod. Slide the link onto the rod

with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the faucet and then into the

hole in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

1/2″(1.3 cm) above the lift rod hole.

Body

Rod

Clip

Stopper

Nut

Flange

Seal

Nut

Tailpiece

Apply

Thread

Sealant.

Thumb

Screw

Stopper Rod

Link

Kohler Co. 9 1033980-2-A

8. Supply Connections

Install the lavatory using the lavatory manufacturer’s instructions.

Connect the supply tubes to the handle valves, and the supply

stops. Left is hot and right is cold.

Tighten all connections.

Supply

Tube

Supply

Tube

1033980-2-A 10 Kohler Co.

Andere Handbücher für K-13132

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler Karbon K-6227D Bedienungsanleitung

Kohler

Kohler Mira Showers Escape Thermostatic 9.8 kW Bedienungsanleitung

Kohler

Kohler Discovery Bedienungsanleitung

Kohler

Kohler Coralais K-15286 Montageanleitung

Kohler

Kohler WaterTile K-8030 Montageanleitung

Kohler

Kohler K-19537P-7 Montageanleitung

Kohler

Kohler Lyntier K-T10333 Montageanleitung

Kohler

Kohler K-10086 Montageanleitung

Kohler

Kohler K-11340X Montageanleitung

Kohler

Kohler Kelston K-T13494 Montageanleitung

Kohler

Kohler OVE Bedienungsanleitung

Kohler

Kohler K-1913 Montageanleitung

Kohler

Kohler Revival K-2950-1 Montageanleitung

Kohler

Kohler K-2268 Montageanleitung

Kohler

Kohler 6625-0 Bedienungsanleitung

Kohler

Kohler Refinia K-T5324 Montageanleitung

Kohler

Kohler K-4350 Series Montageanleitung

Kohler

Kohler K-7128 Montageanleitung

Kohler

Kohler K-7374 Montageanleitung

Kohler

Kohler K-45346T Bedienungsanleitung

Kohler

Kohler STERLING 5300 Series Montageanleitung

Kohler

Kohler K-5826 Montageanleitung

Kohler

Kohler K-7725 Bedienungsanleitung

Kohler

Kohler EVOKE 6332T-B4 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung