Kohler K-14533 Bedienungsanleitung

Installation Guide

Bidet Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página“ Español-1”

K-14533

1015486-2-B

Thank You For Choosing Kohler Company

We appreciate your commitment to Kohler quality. Please take a few

minutes to review this manual before you start installation. If you

encounter any installation or performance problems, please don’t

hesitate to contact us. Our phone numbers and website are listed on

the back cover. Thanks again for choosing Kohler Company.

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect waste and supply tubing for any sign of

damage.

Replace waste or supply tubing if necessary.

For new installations, install the faucet before installing the bidet.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed within the Price Book.

Sealant

Tape

Plumbers

Putty

Adjustable

Wrench

Assorted

Screwdrivers Sealant

1015486-2-B 2 Kohler Co.

1. Faucet Body Installation

NOTE: For single-hole bidets, the escutcheon, spacer and gasket are

not required. Use the rubber washer only.

Apply a bead of plumbers putty to the underside of the faucet

body according to the putty manufacturer’s instructions.

Set the spacer and gasket, with the gasket down, under the center

hole of the escutcheon.

Align the center hole of the escutcheon with the center hole of the

bidet.

Slide the washer over the supply hoses and into the groove on

the faucet body.

Insert the faucet supply tubing into the hole in the bidet.

Insert the lift rod into the hole at the rear of the faucet body.

From the underside of the bidet, place the bracket and nut onto

the mounting stud. Position the faucet with the lift rod toward

the back.

Tighten the nut securing the faucet to the bidet.

Remove excess putty from the escutcheon if it is installed.

Lift Rod

Washer

Spacer

Escutcheon

Supply

Hoses

Faucet

Body Bracket

Hoses

Nut

Lift

Rod

Mounting

Stud

Kohler Co. 3 1015486-2-B

2. Drain Style

Refer to the illustrations above to determine the drain style you

received with your faucet.

Please follow the instructions for your drain style.

Style A Drain Style B Drain

1015486-2-B 4 Kohler Co.

3. Drain Installation-Style A

Remove the protective material from the ﬂange.

Wrap the bottom 2/3 of the ﬂange threads with three layers of

sealant tape.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Insert the ﬂange into the ﬁxture drain hole.

Assemble the gasket (tapered side up) and washer to the ﬂange

and partially thread the nut to the ﬂange. Do not fully tighten the

nut at this time.

Install the body washer and drain body with the seal hole facing

the back of the ﬁxture and securely tighten the nut. Use care to

avoid scratching the ﬁnish.

Remove any excess putty or sealant.

Insert the stopper into the ﬂange.

Insert the seal into the seal hole on the body.

Seal

Stopper

Lavatory

Screw

Spring

Clip Gasket

NutNut

Link

Rod Seal

Flange

Apply Plumbers

Putty.

Apply 3 layers of

sealant tape to

bottom 2/3.

Washer

Body Washer

Drain Body

Kohler Co. 5 1015486-2-B

4. Complete Drain Installation-Style A

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper. Secure

with the body nut.

Remove and adjust the stopper so it lifts about 3/8″(1 cm) when

opened. To adjust, loosen the stopper nut and shorten or lengthen

the stopper as needed. Tighten the stopper nut.

Apply three layers of thread tape and a small bead of pipe

sealant to the tailpiece threads.

Thread the tailpiece to the body and tighten securely.

Slide one end of the clip onto the rod. Slide the link onto the rod

with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the faucet and then into the

hole in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

above the lift rod hole.

Faucet

Rod

Clip

Thumb

Screw

Link

1015486-2-B 6 Kohler Co.

5. Drain Installation-Style B

Remove the protective cover from the ﬂange.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Assemble the nut, ﬂat washer, and tapered gasket (tapered side

up) fully onto the body.

From the underside of the ﬁxture, insert the drain body up into

the drain hole.

From the top of the ﬁxture, securely hand tighten the ﬂange onto

the drain body.

Make sure the drain body seal hole is facing the back of the

ﬁxture, and securely tighten the nut.

Remove any excess putty or sealant.

Apply Plumbers

Putty.

Flange

Gasket

Washer

Nut

Drain Body

Fixture

Kohler Co. 7 1015486-2-B

6. Complete Drain Installation-Style B

Press the seal into the seal hole on the body.

Insert the stopper into the ﬂange.

For regular installations, insert the short end of the rod into the

body seal hole and under the stopper. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper. Hand

tighten the body nut.

Remove and adjust the stopper as needed so it lifts about 3/8″(1

cm) when opened. To adjust, rotate the threaded stopper rod in or

out as needed. Retighten the stopper nut.

Apply thread sealant tape to the tailpiece threads, and thread the

tailpiece to the body. Tighten the tailpiece securely.

Slide one end of the clip onto the rod. Slide the link onto the rod

with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the faucet and then into the

hole in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

1/2″(1.3 cm) above the lift rod hole.

Body

Rod

Clip

Stopper

Nut

Flange

Seal

Nut

Tailpiece

Apply

Thread

Sealant.

Thumb

Screw

Stopper Rod

Link

1015486-2-B 8 Kohler Co.

7. Supply Connections

Install the bidet using the bidet manufacturer’s instructions.

Connect the supply tubes to the handle valve (inlets) and then the

supply stops. (Left is hot - right is cold.)

Tighten all connections.

Supply

Stop

Supply

Hose

Kohler Co. 9 1015486-2-B

8. Installation Checkout

Ensure all coupling juts are tight.

Open the drain.

Turn on the main water supply and check for leaks. Repair as

needed.

Remove the aerator and swivel aerator sleeve by turning it

counterclockwise.

Use a small screwdriver or hex wrench to unscrew the swivel

adapter assembly. Remove the adapter and washer.

Turn the faucet handles on and run hot and cold water through

the spout for about a minute to remove debris. Turn the faucet

off.

Remove any debris from the aerator. Reinstall the washer, swivel

adapter assembly, swivel aerator sleeve, and aerator.

Aerator

Washer

Swivel

Aerator

Sleeve

Swivel

Aerator

Sleeve

1015486-2-B 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-72777 Montageanleitung

Kohler

Kohler OnCue Plus RDC Bedienungsanleitung

Kohler

Kohler Triton Rite-Temp K-T6910-2A Bedienungsanleitung

Kohler

Kohler K-10272 Montageanleitung

Kohler

Kohler BodySpa K-1015 Bedienungsanleitung

Kohler

Kohler K-2443-4 Montageanleitung

Kohler

Kohler K-10217 Bedienungsanleitung

Kohler

Kohler BRAZN K-702245T Bedienungsanleitung

Kohler

Kohler K-23984T-0 Bedienungsanleitung

Kohler

Kohler K-11550 Montageanleitung

Kohler

Kohler 77989T-8A Bedienungsanleitung

Kohler

Kohler 10868T-B4 Bedienungsanleitung

Kohler

Kohler 10586-4-SN Montageanleitung

Kohler

Kohler FAMILY CARE Bedienungsanleitung

Kohler

Kohler K-7127 Montageanleitung

Kohler

Kohler 84625 Handbuch

Kohler

Kohler K-T314 Bedienungsanleitung

Kohler

Kohler 78980T-DR Bedienungsanleitung

Kohler

Kohler K-18647 Montageanleitung

Kohler

Kohler STANCE Bedienungsanleitung

Kohler

Kohler K-15886 Montageanleitung

Kohler

Kohler K-7259 Montageanleitung

Kohler

Kohler K-19909-4 Montageanleitung

Kohler

Kohler K-498 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung