Kohler BRAZN K-702245T Bedienungsanleitung

1463411-T01-A

-1- © Copyright Kohler China Investment Co., Ltd. 2020

ZHONGSHAN KOHLER SHOWER CO., LTD. NO13-1, XINGYE ROAD, ZHONGSHAN TORCH

DEVELOPMENT ZONE, ZHONGSHAN, GUANGDONG, CHINA POST CODE: 528437

中山科勒卫浴有限公司广东省中山市中山火炬开发区兴业路 13-1 号邮编：528437

BEFORE YOU BEGIN 安装之前

• 说明书中所有的资料是按最新出版的产品资料编写而成。科

勒中国有限公司保留任何时候无须通知即可改变产品特性、

包装或产品可供类型的权利。

•说明书包括重要的安装、清洁及保养方面的内容，请把这些

资料交给用户阅读，保管。

• 确保在安装淋浴房之前已经完整正确地安装了浴室和完工

墙面材料。淋浴区墙地面应做防水处理，并不得布置有电器

开关、插座。确保地面排水通畅。

•在进行淋浴房安装之前，请拿出、排列并确认所有的零部件。

请参考第 2 页上所示的分解图。

• 对尺寸与本标准产品不同的定制淋浴房，参照本说明书进行

安装。

• 本产品符合 QB 2584-2007。

• All information is based on the latest product information

available at the time of publication. Kohler China Ltd.

reserves the right to make changes in product

characteristics, packaging, or availability at any time

without notice.

•These instructions contain important care, cleaning, and

warranty information-please leave these instructions for

the consumer.

• Make sure that the bath and the finished wall material are

completely and correctly installed prior to installing your

shower door. Prepare waterproof layer to wall and floor of

the showering area. It is not allowed for any presence of

electric switches and sockets. Make sure the floor drain

runs smoothly.

•Before starting the door installation, lay out and identify all

the parts. Use the exploded view illustrated on page 2 for

reference.

• For the installation method of customized shower with

different dimensions, please refer to this instructions.

•The product complies with QB 2584-2007.

警告：可能有人员伤害或者产品损坏的危险。

钢化玻璃不能进行切割，钻孔或硬物敲击。搬移或安装过

程中，小心确保玻璃边、角部位不受撞击，以防爆裂伤人。

建议：将本产品安装在科勒淋浴盆或挡水条上（需另行购买）。

如自备挡水条，建议顶面宽度尺寸大于 80mm。

重要事项：淋浴房需要安装在平坦垂直的墙面上。墙面的垂直度推

荐在正负 3mm/m 以内。如果超出此范围，科勒公司将不保证淋浴

房的完美使用。

CAUTION: Risk of injury or product damage.

Tempered glass cannot be cut, drilled or knocked by

hard object. Make sure corner area of the glass

refraining from knocking so as to cause personal injury

due to broken glass.

ATTENTION: Please install this door on Kohler receptors or

curbs(Not included). If the curb is not Kohler-branded, please

note its top width should be more than 80mm.

IMPORTANT: The shower door requires a flat vertical

finished wall. The squareness of the wall is recommended no

more than 3mm/m. KOHLER Company won't take

responsibility of the installation quality.

24hrs

ROUGHING-IN 尺寸图

Do not use the enclosure for at least 24 hours.

安装后 24 小时内请勿使用淋浴房。

Unit: mm

单位：毫米

BRAZN 凌越

INSTALLATION INSTRUCTIONS

安装说明书

PIVOT, T SHAPE 3P2D, 10mm

T 型三固二活，10mm

K-702245T

SKU L R

K-702245T 250-1000

1850-22001800-3000

Tools Required/所需工具

5mm Allen Key

5mm 六角扳手

2.5mm Allen Key

2.5mm 六角扳手

Masonry Drill &

6mm Drill Bit

冲击钻以及

6mm 冲击钻头

Pencil

铅笔

Level

水平仪

Measuring Tape

卷尺

Phillips Screwdriver

十字螺丝刀

Hammer

锤子

Knife

刀片

Caulk Gun

硅胶枪

Safety Goggles

护目镜

-2-

1463411-T01-A

X15

Glass Magnetic 门玻磁条

Magnetic 嵌入式磁条

Top Cap, SS 顶装饰盖-A

T Shape Cap, SS T型装饰盖

T Shape Connect Piece, SS T型连接片

Side Seal 侧边防水胶条

Protect Strip 固玻底部保护胶条

BRAZN Pivot Handle, Double Handle, L=1025mm 凌越对装拉手

Screw M4×7 十字沉头螺丝M4×7

Screw M5×20 不锈钢紧定螺丝M5×20

Pan Screw PM4×12 十字盘头机制螺丝PM4×12

Pan Screw PM4×25 十字盘头机制螺丝PM4×25

Pan Screw ST3.5×40 十字盘头自攻螺丝ST3.5×40

Hollow Wall Anchor, Nylon 膨胀套

Insert Seal 单边胶条

Insert Seal 单边胶条(固玻底部用)

Seal Assy, Glass Door, BRAZN Pivot 回水槽组件

Decorative Strip 装饰胶条

T Shape Side Top Rail, SS T型侧扇上横梁

T Shape Side Bottom Rail, SS T型侧扇下横梁

Al Frame, T Shape To Glass T型侧固铝材

L Shape Top Rail, SS L型上横梁

L Shape Bottom Rail, SS L型下横梁

Wall Jamb Clamp, SS 竖材

T Shape Al Frame Inner Profile, SS T型转角型材内盖材

Bottom Base Cap 门玻固定座装饰盖

Silicone Block 硅胶防撞块

Bottom Washer 门玻固定座垫圈

Door Glass Assy 门玻组件

Side Cap, SS 顶侧装饰盖

T Shape Al Frame Outer Profile, SS T 型转角型材外盖材

Bottom Rail Cover 底横梁盖材

Top Hinge Assy 上转轴组件

Bottom Base, Door 门玻固定座

Al Frame, T Shape To Glass

T 型侧固铝材

T Shape Al Frame

Outer Profile, SS

T 型转角型材外盖材

Glass Magnetic

门玻磁条 ×2

Door Glass Assy

门玻组件 ×2

Side Seal

侧边防水胶条 ×2

Hinge Panel Glass

固定玻璃

Insert Seal

单边胶条

Wall Jamb Clamp, SS

竖材

Pan Screw

十字盘头机制螺丝 PM4×25×6

Side Cap, SS

顶侧装饰盖 ×3

Screw

十字沉头机制螺丝 M4×7×9

Top Cap, SS

顶装饰盖-A ×2

Top Hinge Assy

上转轴组件 ×2

Screw

紧定螺丝 M5×20×2

Pan Screw

十字盘头机制螺丝 M4×12×4

T Shape Cap, SS

T 型装饰盖

T Shape Side Profile, SS

T型侧扇竖材

Side Panel Glass

侧扇固玻

T Shape Side Top Rail, SS

T型侧扇上横梁

T Shape Al Frame

Inner Profile, SS

T 型转角型材内盖材 ×2

Wall Jamb Clamp, Left, SS

左竖材

Hinge Panel Glass

固定玻璃

T Shape Bottom Rail, SS

T型下横梁

Bottom Rail Cover, SS

下横梁装饰盖材 ×2

Seal Assy, Glass Door, BRAZN Pivot

回水槽组件

T Shape Side Bottom Rail, SS

T 型侧扇下横梁

Bottom Base Cap

门玻固定座装饰盖 ×2

Bottom Base, Door

门玻固定座 ×2

Bottom Washer

门玻固定座垫圈 ×2

Silicone Block

防水硅胶块 ×2

Protect Strip

固玻底部保护胶条 ×3

BRAZN Pivot Handle,

Double Handle

L=1025mm 凌越对装拉手 ×2

-3-

INSTALLATION 安装

1463411-T01-A

IMPORTANT:

Tray MUST be level

along front edge.

重要：

底盘必须水平。

0mm

STEP

Install side leaf glass and side leaf upper beam.

安装侧扇固玻和侧扇上横梁。

Install the protective seal of the two sides of the fixed glass and the fixed glass, and install

the beam:

1. Place the protective seal of the fixed glass first.

2. Install the fixed glass.

3. Install the beam downwards, and then lock it by the screws.

安装两侧固玻保护胶条和固玻，安装上横梁:

1. 先放置固玻保护胶条；

2. 安装固玻；

3. 自上而下安装上横梁，再锁上螺丝。

PM4×25×4

22mm

Install the vertical member of the side leaf which must be vertical to the floor and installed

in the middle together with the seal.

安装侧扇竖材，侧扇竖材需保持与地面垂直，且与挡水条居中安装。

Install the front upper-wall profile and the front lower beam with the former vertical to the

floor and 20mm from the external edge (stone base surface width is 80mm).

安装正面上墙材和正面下横梁，上墙材需保持与地面垂直，且内偏 20mm 安装（石基面宽

80mm）。

Install the magnetic strip of the center pillar and the center pillar:

1. Insert the magnetic strip into the profile downwards.

2. Pat the whole profile into the fixed glass.

3. Check to confirm the distance from both sides to the fixed glass is about 663mm (the door

glass width is 650mm).

4. Lock by the fixing screws on the top of the center pillar.

安装中立柱磁条和中立柱 :

1. 先将磁条自上而下插入型材；

2. 再将型材整体拍入侧扇固玻；

3. 检查两侧到固玻间距为 663mm 左右（门玻宽度 650mm）；

4. 锁上中立柱顶部固定螺丝。

Note: Check whether the lower beam of

the side leaf has been pre-installed on

the side fixed glass.

注意：检查侧扇下横梁是否已预装在侧

固玻上。

注意:固玻需贴住硅胶防撞块

The wall jamb

must be kept

vertical.

上墙材必须垂直。

0mm

Note: Both the vertical member of

the side leaf and the seal are

installed in the middle.

注意：侧扇竖材与挡水条居中安装。

663mm 663mm

Install the tube so that it is horizontal.

放置挡水条，需确保挡水条放置水平。

Note: There are four M4 thread holes with

each side being locked by one screw.

注意：四个 M4 牙孔，每边能各能锁一个

螺丝即可。

Side distance: 20mm

距边20mm

6mm

0mm

6mm

Install the door glass,

Step 1: Lift the door glass and insert it into the base of the lower beam.

Step 2: Put the door glass in right position and set the upper beam into the rotating shaft

assembly on the top.

Step 3: Lock the screws and set screws

(Note: Both the upper rotating shaft assembly and the lower base of the door glass can be

adjusted leftwards and rightwards, loosen the screws, adjust them into the appropriate

position and then lock them).

安装门玻，

第一步：将门玻抬起插入下横梁底座；

第二步：摆正门玻，上横梁套入顶部转轴组件；

第三步：锁上螺丝和紧定螺丝。

（注意：门玻上转轴组件和下底座都可以左右调节，松开螺丝，调整合适位置在锁紧即可）。

Install the stainless steel decorative material of the lower beam, the rotating shaft base, the

washer and the silicone bumper block, then install the decorative seal, and finally lock the

T-shaped cover of the center pillar.

安装下横梁不锈钢装饰材、转轴底座、垫圈和硅胶防撞块，安装装饰胶条，之后在锁上中立

柱T型盖。

Install the handle and the decorative cover.

安装拉手和装饰盖。

Apply the silicone sealant.

打防水胶。

Install the side seal of the fixed glass (note to distinguish two types of side seals).

Note that there is no need to install side seal at the bottom of the side leaf.

安装固玻单边胶条 (注意区分两种单边胶条 )注意侧扇底部不需要再安装单边胶条。

Install waterproof seal and magnetic strip.

安装防水胶条和磁条。

STEP

-4-

1463411-T01-A

8mm

Step 1

第一步

Step 2

第二步

Step 3

第三步

Note: The two beams are aligned and spliced

together, and then tightened by the screws.

注意:两根横梁对齐拼接，再锁紧螺丝。

12mm

Step 1: Insert the decorative material of the lower beam into

the rotating shaft base in the direction of the arrow.

Step 2: Install the whole part on the lower beam.

Step 3: Adjust the left and right position of the decorative

material of the lower beam and lock by the screws.

第一步，下横梁装饰材按箭头方向插入转轴底座；

第二步，整体安装在下横梁；

第三步，调整下横梁装饰材左右位置，锁上螺丝。

Screw

十字沉头螺丝 M4×7

Screw

紧定螺丝 M5×20

Screw

十字沉头螺丝M4×7×2

Note: Sufficient support

must be

provided when installing

the door glass.

注意：安装门时需有足够

支撑。

Note: Sufficient support must

be provided when installing

the door glass.

注意：安装门时需有足够支撑。

Note: After installation, the magnetic strip is

flush with the waterproof seal.

注意：磁条安装后与回水胶条是平齐状态。

Note: There is a cutout in the side seal, and the

cutout must be flush with the end surface during

installation.

注意：侧边胶条有剪缺，安装时缺口平齐端面即可。

Screw

十字沉头螺丝M4×7×2

Note: The top wire of the handle

is facing down.

注意：拉手顶丝朝下。

Note: The height of the two

side seals is 12mm.

注意：此两处单边胶条高度

为12mm。

Note: The height of the side seal at

the bottom is 8mm, and it needs to

be attached to the stainless steel

decorative cover during installation.

注意：底部单边胶条高度为 8mm，

且安装时需要贴到不锈钢装饰盖。

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-616 Montageanleitung

Kohler

Kohler K-877 Kurzanleitung

Kohler

Kohler 1283722 Bedienungsanleitung

Kohler

Kohler KUMIN 98827IN-4/4ND Series Bedienungsanleitung

Kohler

Kohler K-3900 Bedienungsanleitung

Kohler

Kohler 72842T-4ND Bedienungsanleitung

Kohler

Kohler K-476, K-477 Montageanleitung

Kohler

Kohler K-15888 Bedienungsanleitung

Kohler

Kohler K-72218 Bedienungsanleitung

Kohler

Kohler MF0002KE-00 Bedienungsanleitung

Kohler

Kohler K-812-H2 Montageanleitung

Kohler

Kohler K-6506 Bedienungsanleitung

Kohler

Kohler 8022A Bedienungsanleitung

Kohler

Kohler Coralais K-15286 Montageanleitung

Kohler

Kohler K-45346T Bedienungsanleitung

Kohler

Kohler K-1630-L Bedienungsanleitung

Kohler

Kohler K-T14783 Montageanleitung

Kohler

Kohler ARCHER K-2595-GW Bedienungsanleitung

Kohler

Kohler K-8801 Montageanleitung

Kohler

Kohler K-T387 Bedienungsanleitung

Kohler

Kohler Caxton K-2216 Bedienungsanleitung

Kohler

Kohler K-15635 Bedienungsanleitung

Kohler

Kohler K-2098 Montageanleitung

Kohler

Kohler 74053T-4E2 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung