Kohler K-20199 Montageanleitung

Installation and Care Guide

Bridge Cabinet

K-20199

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página “Español-1”

1304473-2-A

Tools and Materials

Before You Begin

CAUTION: Risk of property damage. Select 250 lb (113.4

kg) load bearing 5/16″lag bolts with a length to clear

obstacles in the wall and 5/16″washers. Calculate proper lag

bolt length by adding the following: 1-1/2″(38 mm) backing

material + wallboard thickness + back rail thickness.

IMPORTANT! Risk of property damage. Use care when moving

the cabinet to avoid impacting, sliding, or side-loading the legs.

NOTE: The K-20199 bridge cabinet is designed to be installed with

the K-20195 vanity and is not intended to be installed individually.

Read both product installation instructions before beginning. The

vanity should be installed before the bridge cabinet.

Observe all local building codes.

To properly secure the cabinet, 2x6 backing material must be

installed behind the ﬁnished wall. Refer to the K-20195 vanity

installation instructions for site preparation.

Siliconized Acrylic

Caulk

Plus:

• 5/16" Lag Bolts and Washers

• Pad

• 2x6s

• Common Plumbing and Woodworking

Tools and Materials

1304473-2-A 2 Kohler Co.

1. Install the Legs

IMPORTANT! Legs are not required for installation between two

vanities.

NOTE: To protect the ﬁnished surface of the cabinet, perform

assembly tasks on a ﬂat, padded work surface.

Position the cabinet on a ﬂat, padded surface.

Remove the drawer to access the holes for leg attachment. Refer

to the ″Remove/Reinstall the Drawer″section of this guide.

Attach the Legs

For Installation to One Vanity Only: Determine whether the legs

will be installed on the left or right. The opposite side will be

supported when installed to the K-20195 vanity.

Position the cross rail above the clips in the front and back legs.

Press down ﬁrmly and evenly on the cross rail until it fully

engages into the clips.

Secure the leg assembly to the bridge cabinet using four #8 x 2″

panhead screws, lock washers, and ﬂat washers (provided).

Kohler Co. 3 1304473-2-A

2. Position the Bridge Cabinet

CAUTION: Risk of personal injury. Select 250 lb (113.4 kg)

load bearing 5/16″lag bolts with a length to clear obstacles

in the wall and 5/16″washers. Calculate the proper lag bolt

length by adding the following: 1-1/2″(38 mm) backing

material, plus the wallboard thickness, plus the back rail

thickness.

IMPORTANT! Risk of product damage. Use care when moving the

bridge cabinet to avoid impacting, sliding, or side-loading the legs.

NOTE: The K-20199 bridge cabinet is designed to be installed with

the K-20195 vanity and is not intended to be installed individually.

Read both product installation instructions before beginning

installation. Install the vanity before the bridge cabinet.

Install Spacers (provided) – Only for Installation to a Vanity

IMPORTANT! Ensure spacers do not extend past the top front edge

of the bridge cabinet. Improper placement of spacers may interfere

with the installation of the stone top.

Remove the protective ﬁlm from the adhesive strips on one of the

spacers.

Carefully position the spacer on the side of the bridge cabinet,

ﬂush with the top and front edges.

Install a second spacer on the side of the bridge cabinet, ﬂush

with the top and back edges.

Spacer

1304473-2-A 4 Kohler Co.

Position the Bridge Cabinet (cont.)

To Install Between Two Vanities: Flip the bridge cabinet over

and repeat these steps for the other two spacers.

Position and Level

To properly secure the bridge cabinet, 2x6 backing material must

be installed behind the ﬁnished wall. Refer to the K-20195 vanity

installation instructions for site preparation.

Verify the bridge cabinet is level and ﬂush against the vanity and

that the front edges are aligned. If necessary turn the leveler(s) to

adjust the unit.

Kohler Co. 5 1304473-2-A

3. Secure the Bridge Cabinet

Make sure the bridge cabinet is tight against the vanity.

Using a 1/4″drill bit, drill two pilot holes through the back rail

and the ﬁnished wall. Verify the pilot holes are positioned to

ensure the lag bolts will engage the 2x6 backing material.

Using a 1/8″drill bit, drill two pilot holes through the side of the

bridge cabinet and into the vanity.

Secure the bridge cabinet to the ﬁnished wall with two 5/16″lag

bolts and washers (not provided).

Secure the bridge cabinet to the vanity using two #8 x 1-1/2″

panhead screws (provided). Use shims as needed to make the

bridge cabinet level and ﬂush with the vanity.

For Installation to Two Vanities

Install the second vanity according to the instructions packed

with the vanity. Ensure the vanity is ﬂush against the front of the

bridge cabinet before securing the vanity to the wall.

Using a 1/8″drill bit, drill two pilot holes through the side of the

bridge cabinet and into the second vanity.

Secure the bridge cabinet to the second vanity using two #8 x

1-1/2″panhead screws (provided).

1304473-2-A 6 Kohler Co.

4. Install the Stone Top

Apply a 1/2″(13 mm) dab of siliconized acrylic caulk in each top

corner of the bridge cabinet.

IMPORTANT! Make sure the ﬁnished side of the stone top faces

upward when installed.

Single Vanity Installations: Position the stone top so the back is

ﬂush with the wall and the side is ﬂush with the vanity. Press

down ﬁrmly.

Double Vanity Installations: Position the stone top so the back is

ﬂush with the wall and the top is centered between the two

vanities. Press down ﬁrmly.

Install spacers as instructed at the beginning of this section.

All Installations: Immediately wipe away any excess caulk.

Kohler Co. 7 1304473-2-A

5. Remove/Reinstall the Drawer

Remove

Slide the drawer out until fully extended.

From underneath, pull the release latches toward the center of the

drawer.

Lift the front of the drawer and pull toward you to disengage

from the rails.

Once removed, lay the drawer on a ﬂat, protective surface.

Reinstall

Fully extend the rails.

Align the holes in the back of the drawer with the rail hooks.

Rotate the drawer down onto the rails, engaging the front drawer

holes with the rail pins.

From underneath, push the release latches into the rails to secure

the drawer.

Install the Knob

NOTICE: Ensure that the knob location you choose will provide

unobstructed clearance when opening and closing the door.

Select and mark the desired knob location on the door.

Use a 3/16″bit to drill the marked hole location.

From the inside of the door, insert the screw through the hole.

Latch

Rail

Hook

Holes

Knob

Screw

1304473-2-A 8 Kohler Co.

Remove/Reinstall the Drawer (cont.)

Thread the knob onto the screw. Securely hand-tighten.

Care and Cleaning

For best results, keep the following in mind when caring for your

KOHLER product:

Marble

NOTE: Application of a stone sealer will help make natural stone

surfaces less porous and more resistant to stains (stone sealer will

not make the surface stain proof).

•Marble is a natural stone, thus its color and pattern can vary

greatly. Each marble surface has its own distinct characteristics.

This individuality makes each marble ﬁxture a unique and

original addition to your home.

•If a marble surface is given the proper care, it will retain its

beauty and durability. Without regular cleaning, dust particles can

settle on marble and can be ground into the surface and cause

damage. Wash marble regularly with fresh warm water and a

clean non-abrasive cloth. Add a neutral (ph balanced) cleaner to

help remove dirt and grime.

•Avoid detergents that can be abrasive and contain chemicals high

in acid or alkaline. Petroleum (or oils such as animal fat) can

darken natural stone and leave a residue which, over time, can

build up and turn yellow. This buildup is difficult to remove.

•Give marble the same attention you give to ﬁne wood. Use

coasters under all drink containers. Wipe up stains immediately.

Do not allow heated items to come into contact with the marble

surface. To protect against scratches, use felt, leather, or cork

under all items placed on the marble surface.

Wood Surfaces

•As with any smooth surface, avoid using abrasive cleaners as

they will scratch the surface. Wipe the wood surface regularly to

prevent buildup of soap and scum.

•To protect against scratches, use felt, leather, or cork under all

items placed on the wood surface. To conceal scratches, a

touch-up marker is available for order. Contact a Kohler

distributor or call 1-800-4KOHLER for ordering information.

Kohler Co. 9 1304473-2-A

Care and Cleaning (cont.)

•Do not expose wood furniture to direct sunlight, drying heat

sources, or dampness.

•Dust frequently with a soft cloth in the direction of the grain. Use

only products speciﬁcally made for cleaning wood. Avoid using

oily polishes or waxes, or products containing silicone. Blot spills

immediately with a soft, damp cloth.

•Every six months, remove soil buildup by rubbing with a soft

cloth dampened in a 50/50 solution of warm water and an

ammonia-free detergent. Wipe clean with a cloth dampened in

warm water, then wipe dry.

Warranty

ONE-YEAR LIMITED WARRANTY

KOHLER plumbing products are warranted to be free of defects in

material and workmanship for one year from date of installation.

Kohler Co. will, at its election, repair, replace or make appropriate

adjustment where Kohler Co. inspection discloses any such defects

occurring in normal usage within one (1) year after installation. Kohler

Co. is not responsible for removal or installation costs. Use of in-tank

toilet cleaners will void the warranty.

To obtain warranty service contact Kohler Co. either through your

Dealer, Plumbing Contractor, Home Center or E-tailer, or by writing

Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler,

WI 53044, USA, or by calling 1-800-4-KOHLER (1-800-456-4537) from

within the USA and Canada, and 001-800-456-4537 from within Mexico,

or visit www.kohler.com within the USA, www.ca.kohler.com from

within Canada, or www.mx.kohler.com in Mexico.

IMPLIED WARRANTIES INCLUDING THAT OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE ARE EXPRESSLY LIMITED IN DURATION TO THE

DURATION OF THIS WARRANTY. KOHLER CO. AND/OR

SELLER DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES. Some states/provinces do not

allow limitations on how long an implied warranty lasts, or the

exclusion or limitation of special, incidental or consequential damages,

so these limitations and exclusions may not apply to you. This

warranty gives you speciﬁc legal rights. You may also have other

rights which vary from state/province to state/province.

This is Kohler Co.’s exclusive written warranty.

1304473-2-A 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-10430 Bedienungsanleitung

Kohler

Kohler FOLIO K-2017IN-1 Bedienungsanleitung

Kohler

Kohler 76633T-B Bedienungsanleitung

Kohler

Kohler Caxton K-2216 Bedienungsanleitung

Kohler

Kohler Refinia K-T5324 Montageanleitung

Kohler

Kohler Mira Logic L19B Bedienungsanleitung

Kohler

Kohler K-3820 Montageanleitung

Kohler

Kohler K-15182 Bedienungsanleitung

Kohler

Kohler K-17230T-DR Bedienungsanleitung

Kohler

Kohler ELLISTON 75522T-4 Bedienungsanleitung

Kohler

Kohler K-9511 Bedienungsanleitung

Kohler

Kohler URBANITY 23748T-9 Bedienungsanleitung

Kohler

Kohler Finial 607T Bedienungsanleitung

Kohler

Kohler K-11660 Montageanleitung

Kohler

Kohler K-13700 Bedienungsanleitung

Kohler

Kohler K-7725 Bedienungsanleitung

Kohler

Kohler ESCALE Bedienungsanleitung

Kohler

Kohler K-8807 Bedienungsanleitung

Kohler

Kohler Mira Showers Escape Thermostatic 9.0 kW Bedienungsanleitung

Kohler

Kohler K-11340X Montageanleitung

Kohler

Kohler ARTIFACTS 72798T Bedienungsanleitung

Kohler

Kohler 72282T-4 Service-Handbuch

Kohler

Kohler C3-050 Bedienungsanleitung

Kohler

Kohler RADA FE9 2.1942.005 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung