Kohler K-15182 Bedienungsanleitung

Installation Guide

Centerset Lavatory Faucet

K-15182, K-15186, K-15198,

K-15199, K-15582, K-15583,

K-15592, K-15593, K-15597,

K-15598, K-15681, K-15686,

K-P15182, K-P15186, K-P15199,

K-P15681, K-P15686

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page “Français-1”

Español, página“ Español-1”

1010442-2-D

Tools and Materials

Before You Begin

Observe all local plumbing and building codes.

Shut off the main water supply.

Carefully inspect the waste and supply tubing for any sign of

damage.

For new installations, install the faucet and drain to the lavatory

before installing the lavatory.

Kohler Co. reserves the right to make revisions in the design of

faucets without notice, as speciﬁed in the Price Book.

Plumbers

Putty Pencil Adjustable

Wrench Phillips

Screwdriver

1010442-2-D 2 Kohler Co.

1. Faucet Installation

Clean the lavatory surface to remove any grease, oil, or debris.

Apply a ring of plumbers putty or other sealant around the

underside edge of the faucet body according to the putty

manufacturer’s instructions.

Insert the faucet into the lavatory holes. Check alignment.

Slide a channel and spacer onto each shank.

Thread a nut onto each shank and loosely tighten.

Position the faucet as desired.

Secure the faucet by securely wrench tightening the nuts.

Wipe away any excess sealant.

Channel

Spacer

Nut

Apply

Plumbers

Putty.

Kohler Co. 3 1010442-2-D

2. Pop-Up Drain Installation

Remove the protective cover from the ﬂange.

Apply a ring of plumbers putty or other sealant to the underside

of the ﬂange according to the putty manufacturer’s instructions.

Assemble the nut, ﬂat washer, and tapered gasket (tapered side

up) fully onto the body.

From the underside of the ﬁxture, insert the drain body up into

the drain hole.

From the top of the ﬁxture, securely hand tighten the ﬂange onto

the drain body.

Make sure the drain body seal hole is facing the back of the

ﬁxture, and securely tighten the nut.

Remove any excess putty or sealant.

Apply plumbers putty.

Flange

Tapered Gasket

Washer

Nut

Drain Body

Fixture

Thick Tapered Gasket

(for thin-walled vessel style

lavatory installations)

1010442-2-D 4 Kohler Co.

3. Complete Pop-Up Drain Installation

IMPORTANT! If the tailpiece has been removed, double check that

the plastic washer is installed inside the ﬂange body or the drain

will leak.

Connect the P-trap to the tailpiece.

Press the seal into the lift rod hole on the body.

Insert the stopper into the ﬂange.

For regular installations, insert the short end of the rod into the

lift rod hole and under the stopper rod. For vandal-resistant

installations, ﬁt the rod through the hole in the stopper rod.

Hand tighten the rod nut.

Remove and adjust the stopper as needed so it lifts about 3/8″(1

cm) when opened. To adjust, rotate the threaded stopper rod in or

out as needed. Retighten the stopper nut.

Slide one end of the clip onto the rod. Slide the link onto the lift

rod with the thumbscrew facing the back of the ﬁxture.

Squeeze the other end of the clip, aligning the hole with the rod.

Move the link to the proper position by squeezing the clip and

sliding it along the rod.

Insert the lift rod into the hole in the body and then into the hole

in the link.

Tighten the thumbscrew onto the link so the lift rod knob extends

1/2″(1.3 cm) above the lift rod hole.

Check for leaks.

Body

Clip

Stopper

Flange

Seal

Rod Nut

Tailpiece

Thumb

Screw

Stopper

Rod

Plastic

Washer

Link

Rod

Kohler Co. 5 1010442-2-D

4. Grid Drain Installation

If present, remove the protective plastic cap from the drain and

discard.

Remove the nut, washer, and gasket from the drain body.

Apply a bead of plumbers putty or other sealant around the

underside of the ﬂange according to the sealant manufacturer’s

instructions.

For drains with metal stoppers: Close the drain and rotate the

drain body until the logo is positioned horizontally (as

illustrated).

Insert the drain into the drain hole and press into place.

Slide the gasket (tapered side up) onto the drain body.

Slide the washer over the threads on the drain body.

Thread the nut up the drain body until snug against the

underside of the lavatory. Use care not to rotate the drain while

tightening the nut.

Using a wrench, tighten the nut.

Remove any excess putty or sealant.

Connect the P-trap to the drain body.

Gasket

Washer

Flange

Drain Body

Nut

With the drain

closed, position

so the logo is

horizontal.

Metal Stoppers Only

1010442-2-D 6 Kohler Co.

5. Supply Connections

If the lavatory is not installed, install it at this time according to

the lavatory manufacturer’s instructions.

Allow enough space for penetration of supply tubes into the

supply stops. Cut the supply tubes if necessary.

Connect the supply hoses to the supply stops. (Left is hot - right

is cold).

Tighten all connections.

6. Installation Checkout

Connect the P-trap.

Make sure all connections are tight.

Remove the aerator by turning it counterclockwise.

Open the drain.

Turn on the main water supply and check for leaks. Make any

adjustments as needed.

Open both hot and cold valves and run water through the spout

for about a minute to remove debris. Check for leaks.

Close the hot and cold valves.

Rinse any debris from the aerator and reinstall.

Nut

Compression

Union

HOT

COLD

Spout

Aerator

Kohler Co. 7 1010442-2-D

7. Adjust the Maximum Water Temperature

NOTE: Prior to adjustment, make sure the handle is in the

maximum hot position.

Remove the handle and bonnet.

Turn on the water to the maximum hot water temperature by

pushing the valve stem up, and turning it fully clockwise.

Use a pencil or marker to mark the current position of the

temperature stop tab (top edge) on the mounting nut. Lift both

the indexer and the top disc just enough to clear the splines and

to allow rotation.

NOTE: Each indexer notch is an average 9.5°F (5.3°C) change in

temperature.

Turn the indexer, top disc, and valve stem counterclockwise until

you achieve the desired temperature.

Reinstall the indexer and top disc to the valve. Make sure the top

disc is snapped fully into the indexer.

Turn off the water, and reinstall the bonnet and handle.

Cap

O-Ring

Valve Stem

Splines

Screw

Handle

Bonnet

Stop Tab

Mounting

Nut

Indexer

Top Disk

1010442-2-D 8 Kohler Co.

Guide d’installation

Robinet de lavabo à petit entraxe

Outils et matériels

Avant de commencer

Respecter tous les codes de plomberie et de bâtiment locaux.

Couper l’alimentation d’eau principale.

Vériﬁer avec soin si les tubes d’évacuation ou d’alimentation

d’eau sont endommagés.

Pour de nouvelles installations, installer le robinet et le drain au

lavabo avant d’installer celui-ci.

Kohler Co. se réserve le droit d’apporter toutes modiﬁcations au

design des robinets et ceci sans préavis, comme spéciﬁé dans le

catalogue des prix.

Mastic de

plombier Crayon

à papier

Clé à

molette Tournevis

cruciforme

Kohler Co. Français-1 1010442-2-D

1. Installation du robinet

Nettoyer la surface du lavabo pour éliminer toute graisse, huile

ou débris.

Appliquer du mastic d’étanchéité sur le dessous du rebord du

corps de robinet selon les instructions du fabricant.

Insérer le robinet dans les oriﬁces du lavabo. Vériﬁer

l’alignement.

Glisser une plaque et un espaceur sur chaque manche.

Visser un écrou sur chaque manche et serrer légèrement.

Positionner le robinet selon le désir.

Sécuriser le robinet en serrant bien les écrous à clé.

Essuyer tout excès de mastic.

Plaquette

Écrou

Appliquer

du mastic

d'étan-

chéité

Cale

1010442-2-D Français-2 Kohler Co.

Andere Handbücher für K-15182

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-10349 Montageanleitung

Kohler

Kohler K-1018 Montageanleitung

Kohler

Kohler K-3323X Montageanleitung

Kohler

Kohler K-77963-8A-BL Bedienungsanleitung

Kohler

Kohler K-7341 Montageanleitung

Kohler

Kohler K-1913 Montageanleitung

Kohler

Kohler K-8801 Montageanleitung

Kohler

Kohler 3867T Bedienungsanleitung

Kohler

Kohler K-2816 Bedienungs- und Wartungsanleitung

Kohler

Kohler K-2816 Montageanleitung

Kohler

Kohler K-3099 Bedienungsanleitung

Kohler

Kohler J03I Bedienungsanleitung

Kohler

Kohler K-14281 Bedienungsanleitung

Kohler

Kohler BADRON K-5487T-B Bedienungsanleitung

Kohler

Kohler K-19537P-7 Montageanleitung

Kohler

Kohler K-12181 Montageanleitung

Kohler

Kohler K-6227 Montageanleitung

Kohler

Kohler K-10217 Bedienungsanleitung

Kohler

Kohler K-T944 Bedienungsanleitung

Kohler

Kohler K-6941 Montageanleitung

Kohler

Kohler Coralais Rite-Temp 114522-2-CE Bedienungsanleitung

Kohler

Kohler K-2286 Montageanleitung

Kohler

Kohler K-6132 Montageanleitung

Kohler

Kohler K-5414 Betriebsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung