Kohler K-922 Bedienungsanleitung

Installation Guide

Wall/Ceiling Mount Faucet

Mproduct numbers are for Mexico (i.e. K-12345M)

Los números de productos seguidos de

Mcorresponden a México (Ej.

K-12345M)

Français, page ″Français-1″

Español, página ″Español-1″

K-922, K-923 K-924

1006741-2-G

Tools and Materials

Before You Begin

Shut off the main water supply.

Observe all local plumbing and building codes.

Do not use this ﬂow spout as a showerhead because it will cause

excessive splashing and does not meet showerhead codes.

This ﬂow spout is available in two oriﬁce sizes: 3/4″(2 cm) and

15/16″(2.4 cm). The smaller oriﬁce size is designed for a 5-10

gpm (19-38 lpm) ﬂow rate, and Kohler K-400-K, K-401-K, or

K-306-KS supply valves are recommended. The larger oriﬁce size

is designed for a 7-15 gpm (26-57 lpm) ﬂow rate, and Kohler

K-300-K or K-301-K supply valves are recommended.

NOTE: A ﬂow rate lower than the ﬂow rate listed on the

speciﬁcation sheet may disrupt the water ﬂow.

The drip tray is an optional accessory available for the wall

mount but not for the ceiling mount.

A water hammer arrestor is recommended in ceiling mounted

applications using a high ﬂow, deck mounted valve. Kohler

recommends that a Sioux Chief 652-AD vacuum breaker arrester

be located near the outlet side of the valve. Contact Sioux Chief at

1-800-821-3944 or www.siouxchief.com.

For ceiling mount applications, the height from the bottom of the

bath to the spout should not exceed 9’ (2.7 m).

Tape

Measure Tape

Measure

Silicone

Sealant

Adjustable

Wrench

Propane

Torch

Plus:

• 2x4 Lumber

• 1x3 Lumber

• Pipe Strap

Screwdrivers

Pencil

Drill Solder

Level

1006741-2-G 2 Kohler Co.

Before You Begin (cont.)

In applications where excessive air could enter the water supply,

install an air separator.

When a deck mounted transfer valve (K-408-K or K-409-K) is

used for a ceiling mount, install a check valve between the spout

and the diverter.

Remove the mounting sleeve and cartridge before installing the

spout body.

Kohler Co. reserves the right to make revisions in the design of

products without notice, as speciﬁed in the Price Book.

Kohler Co. 3 1006741-2-G

1. Determine the Location

CAUTION: Risk of property damage. When employing a

wall mount installation, install this spout at the end of the

bathing ﬁxture so the water stream projection stays within

the bathing ﬁxture.

There are three recommended installation conﬁgurations for the

spout: 1) offset wall mount, 2) center wall mount, and 3) ceiling

mount. The offset wall mount is highly recommended for the

safety of the user.

Offset Installation

The spout assembly is placed 7″(17.8 cm) from the center of the

bathing ﬁxture, away from the entry side of the ﬁxture.

The offset conﬁguration allows users to avoid the stream of water

when entering or using the bathing ﬁxture.

Center Installation

The spout assembly is positioned directly above and on the

centerline of the bathing ﬁxture.

This installation should only be used when the offset installation

is not possible.

7" (17.8 cm)

Bath

Enter

Offset Installation

Bath

Center Installation

1006741-2-G 4 Kohler Co.

2. Ceiling Installation Layout

Install the spout in the ceiling over the bathing ﬁxture at the

shaded areas shown in the illustration.

Mount the spout so it is 9’ (2.7 m) or less from the bottom of the

bathing ﬁxture.

Locate the spout so the water stream contacts the ﬂat bottom of

the bathing ﬁxture. Excess splashing will occur if the water

stream contacts whirlpool jets or bathing ﬁxture corners.

Enter

One Bather

Enter

Two Bathers

Ceiling Installation Range

Kohler Co. 5 1006741-2-G

3. Install the Drip Tray Mounting Plate

NOTE: The drip tray is an optional accessory available for wall

mount but not for ceiling mount.

NOTE: Install the 2x4’s so the drip tray is level or has a slight

forward slope to ensure proper drainage.

Attach a 2x4 ﬂush to the back of the wall stud to support the

lower lip of the drip tray mounting plate. Position the 2x4 so it

will be 2″(5.1 cm) above the top of the bathing ﬁxture.

Attach a second 2x4 so it is 5-5/8″(14.3 cm) above the ﬁrst 2x4.

NOTE: When 2x6 wall studs are present, install the 2x4’s so they are

supported 2″(5.1 cm) from the back of the wall stud.

Attach the drip tray mounting plate to the 2x4’s using six drywall

or #10x1″screws. Make sure the mounting plate is centered under

the spout’s location.

Stud

Install nut

and

washer.

Mounting

Plate

Bathing

Fixture

5-5/8"

(14.3 cm)

(5.1 cm)

2x4's

Backup

Plate

Drywall or

#10 Wood

Screws

1006741-2-G 6 Kohler Co.

4. Install the Spout – Wall Installation

Install a 2x4 for spout support so it lays ﬂush against the top

support of the drip tray. If the drip tray is installed, the spout

center must be 7-5/8″(19.4 cm) from the drip tray mounting

studs. If the drip tray is not installed, the spout center must be

14-16″(35.6-40.6 cm) from the deck of the bathing ﬁxture.

NOTE: When 2x6 wall studs are present, the front of the 2x4 must

be ﬂush with the front of the wall stud.

Install a 1x3 so it is 4″(10.2 cm) above the 2x4 and inset 3/8″(1

cm) from the back of the studs. The larger side of the 1x3 must

face outward.

NOTE: When 2x6 wall studs are present, install the 1x3 so it is

2-3/8″(6 cm) from the back of the wall stud.

Place the spout assembly into position. Verify that the spout and

drip tray mounting plate (if installed) are centered.

Remove the boot cap from the end of the intake pipe.

Remove the mounting sleeve and cartridge.

Spout

Assembly

Intake

Pipe

Valve Outlet Tubing

Pipe Strap

7-5/8"

(19.4 cm)

(10.2 cm)

3/8"

(1 cm)

2x4

1x3

Kohler Co. 7 1006741-2-G

Install the Spout – Wall Installation (cont.)

Solder the intake pipe to the valve outlet tubing.

Secure the valve outlet tubing to the 1x3 using a pipe strap.

1006741-2-G 8 Kohler Co.

5. Install the Spout – Ceiling Installation

Install a 2x4 for support in the location where the spout will be

mounted. Position the 2x4 support so it is 3-3/4″(9.5 cm) from

the bottom of the joist.

Install the spout assembly to the 2x4 using two wood screws,

inserted at the angles shown, through the holes in the back plate.

Remove the boot cap from the end of the intake pipe.

Remove the mounting sleeve and cartridge.

Solder the intake pipe to the valve outlet tubing.

Back Plate

2x4

Screw

Intake Pipe Spout

Assembly

3-3/4"

(9.5 cm)

Kohler Co. 9 1006741-2-G

6. Complete the Installation

Complete the ﬁnished wall and/or ceiling.

If installing the optional drip tray, make sure the studs are

positioned and tightened correctly.

Apply silicone sealant to the groove in the ﬂange of the mounting

sleeve.

Insert the mounting sleeve in the spout. Align the three screw

holes.

Finished

Wall

7-5/8"

(19.4 cm)

1-1/2"

(3.8 cm)

Mounting

Sleeve

Mounting

Plate

Installed

Spout

1/2" D. (1.3 cm) holes

(optional drip tray studs)

3-3/8" D. (8.6 cm)

(spout hole)

3" (7.6 cm)

Add sealant

to groove.

1006741-2-G 10 Kohler Co.

Andere Handbücher für K-922

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler SKYLINE Series Bedienungsanleitung

Kohler

Kohler Mira Showers Escape Thermostatic 9.0 kW Bedienungsanleitung

Kohler

Kohler Wave 72687X-4 Bedienungsanleitung

Kohler

Kohler K-T5323 Montageanleitung

Kohler

Kohler Purist 7505D Bedienungsanleitung

Kohler

Kohler MOXIE 99107T Bedienungsanleitung

Kohler

Kohler K-6814 Montageanleitung

Kohler

Kohler K-6331 Bedienungsanleitung

Kohler

Kohler K-2443-4 Montageanleitung

Kohler

Kohler C3-150 Montageanleitung

Kohler

Kohler 10-Jet K-1000-H2 Bedienungsanleitung

Kohler

Kohler K-1418-GCR Kurzanleitung

Kohler

Kohler K-13490 Montageanleitung

Kohler

Kohler Purist K-T97328-4-BN Bedienungsanleitung

Kohler

Kohler K-T13141 Montageanleitung

Kohler

Kohler K-7166-AF Montageanleitung

Kohler

Kohler K-146 Montageanleitung

Kohler

Kohler K-2032-0 Bedienungsanleitung

Kohler

Kohler 8959X-9 Bedienungsanleitung

Kohler

Kohler KT6908 Bedienungsanleitung

Kohler

Kohler Mira Zest Bedienungsanleitung

Kohler

Kohler PATIO ECO K-18645T-Y Bedienungsanleitung

Kohler

Kohler SYMBOL 72640X Bedienungsanleitung

Kohler

Kohler Trend K-11935 Montageanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung