Kohler Purist K-T97328-4-BN Bedienungsanleitung

Installation Instructions

Floor-Mount Bath Faucet

Français, page “Français-1”

Español, página “Español-1”

1443291-2-A

Tools

Important Information

CAUTION: Risk of personal injury. Do not use the bath

filler as a grab bar or support bar when entering or exiting

the bath. The bath filler is not designed to support weight.

NOTICE: To avoid damage to the O-rings on the bottom of the

faucet, keep the faucet vertical and use care when installing the

faucet.

NOTE: A minimum operating pressure of 45 psi (310 kPa) is

required for proper operation. If a pressure of less than 45 psi (310

kPa) is present, contact a plumber or choose another faucet.

For use with automatic compensating valves rated at 1.6 gal/min

(6.1 l/min) or less.

Follow all local plumbing and building codes.

Turn OFF the water supply.

A drill bit is provided for installation to wood support. Use an

appropriate drill bit for other materials.

The dimensions given assume the spout and bath are mounted on

the same surface. Adjust the dimensions accordingly if the spout

and bath are mounted on different surfaces.

If this product is installed with an overflowing bath, the outer rim

of the bath should slightly overlap the 2x4 framing.

Installer supplied copper tubing must be 5/8″OD (1/2″

Nominal).

Carefully review this document and all appropriate roughing-in

information. Design the bath enclosure accordingly.

Sealant Tape

Plus:

• 3/16" Masonry Bit (for concrete installation)

• Conventional Woodworking Tools and Materials

• Plumbing Tools and Materials

1443291-2-A 2 Kohler Co.

Important Information (cont.)

The appearance of your faucet may differ from the illustrations in

this guide. The instructions still apply.

Kohler Co. 3 1443291-2-A

1. Prepare the Site

IMPORTANT! 2x6 lumber is NOT adequate for this application.

Wood Support

Finished

Wall

7-7/8"

(200 mm)

Min

Finished

Floor

2-3/4"

(70 mm)

Min

Bath

Base

Centerline

2-1/4"

(57 mm) Min

3-1/16"

(78 mm) Max

Floor Joist

1443291-2-A 4 Kohler Co.

Top of the

Finished Floor

Prepare the Site (cont.)

NOTICE: Adequate floor support is required. The wood support must

be a minimum of 2″ (51 mm) thick by 6″ (152 mm) wide. 2x6 lumber is

NOT adequate for this application.

NOTE: Concrete can be used as the floor support, as long as the faucet

base will be below the finished floor level.

Plan out the bath filler placement based on the dimensions above.

Cut a hole in the subfloor that is large enough to install the wood

support between two floor joists.

Secure the wood support between 2-1/4″ (57 mm) to 3-1/16″ (78 mm)

below the top of the finished floor.

Kohler Co. 5 1443291-2-A

2. Spout Orientation

NOTE: Verify correct spout orientation before securing the base to

the wooden support.

NOTE: The base has a blue mark and a notch on the cold supply

side.

Orient the base with the cold supply side notch placed in the

direction shown.

If possible, dry fit the faucet to the base using the screws and

washers. Orient the spout to the inside of the bath.

If your faucet is not available at this time, make sure that the base

is positioned so water from the spout will properly flow into the

bath.

Mark the mounting-hole locations on the wooden support.

Mark the orientation of the base, and where the notch is

positioned on the wooden support.

Cold

Bath

Hot

Pencil

Wall

Top View

Base

1443291-2-A 6 Kohler Co.

3. Install the Base

If attached, remove the faucet from the base.

Use a 3/16″drill bit (provided) to drill 1-1/2″(38 mm) deep

holes at the marked locations.

If using concrete as the floor support, use a 3/16″masonry bit

(not provided) to drill 1-1/2″(38 mm) deep holes at the marked

locations.

Realign the base to the position you marked. Make sure that the

cold supply notch is in the correct orientation.

Secure the base to the support with the screws and washers

(provided).

Verify that the base is level, and tighten the screws.

Screw

Washer

Base

3/16"

Mounting Hole

Wood Support

Floor Joist

Kohler Co. 7 1443291-2-A

4. Connect the Supplies

NOTE: The base has a blue mark and a notch on the cold supply

side.

Apply sealant tape on the 1/2″NPT hot and cold supply pipes,

and thread into the base.

Insert the plug into the base.

Turn ON the water supply and check for leaks.

Turn OFF the water supply.

Secure the guard onto the base with the screws (provided).

Blue Mark

Base

Notch

Cold Supply

Hot

Supply Plug Screw

Guard

1443291-2-A 8 Kohler Co.

5. Install the Finished Floor

Finish the floor leaving a 3″(76 mm) diameter hole for the guard.

Cut the guard so it is flush with the finished floor.

Finished Floor

Guard

Ø 3"

(76 mm)

Fit the finished floor

between the

Min and Max lines.

Kohler Co. 9 1443291-2-A

6. Install the Faucet

NOTICE: Keep the faucet vertical during installation to avoid

damaging the faucet O-rings.

Make sure that the water is turned OFF.

Carefully relieve the water pressure.

Remove the plug from the base.

Remove the rubber protector (not shown) from the faucet.

Make sure that the base is completely free of dirt and debris.

Position the faucet on the base, and insert the screws and washers

(provided) through the flange.

Tighten the screws using the hex wrench (provided).

Slide the escutcheon down onto the floor to cover the base.

Washer

Base

Plug

O-Rings

Flange

Screw

Hex

Wrench

Escutcheon

1443291-2-A 10 Kohler Co.

Inhaltsverzeichnis

Sprachen:

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler ODEON K-8766 Bedienungsanleitung

Kohler

Kohler K-4991X Montageanleitung

Kohler

Kohler K-1035-H2 Montageanleitung

Kohler

Kohler 72218T-B7-CP Montageanleitung

Kohler

Kohler K-10121 Bedienungsanleitung

Kohler

Kohler K-1002-H2 Bedienungsanleitung

Kohler

Kohler K-T314 Bedienungsanleitung

Kohler

Kohler K-2271 Bedienungsanleitung

Kohler

Kohler K-168 Bedienungsanleitung

Kohler

Kohler K-7305 Betriebsanleitung

Kohler

Kohler Sunstruck K-24009-GH Bedienungsanleitung

Kohler

Kohler Botticelli K-2333 Bedienungsanleitung

Kohler

Kohler K-7166-AF Montageanleitung

Kohler

Kohler K-17230T-DR Bedienungsanleitung

Kohler

Kohler PureWash K-98804 Bedienungsanleitung

Kohler

Kohler Fairfax K-12265 Montageanleitung

Kohler

Kohler K-8593 Montageanleitung

Kohler

Kohler K-2443 Bedienungsanleitung

Kohler

Kohler K-15227 Series Montageanleitung

Kohler

Kohler KUMIN K-18655T-B-CP Bedienungsanleitung

Kohler

Kohler K-4108BR Bedienungsanleitung

Kohler

Kohler ODEON K-8711T Bedienungsanleitung

Kohler

Kohler 22572T-9 Bedienungsanleitung

Kohler

Kohler K-7163 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung